Checkpoint SLA Series Technisches Datenblatt

This document applies to vertical and horizontal motor orientations.

Tool Requirements

•Open-End Wrenches: Sizes required will depend on motor frame

•1/8” Hex Key

Pump Mounting

1. Unpack Series SLA pump assembly, and ensure all ordered components are

supplied. Fastener hardware not included. Motor sold separately.

QTY

DESCRIPTION

SERIES SLA PUMP

SHAFT COUPLING HUB + SPIDER

2. Place pump onto level mounting surface. The head should always be horizontal

relative to ground with the discharge check valve vertical facing up. See Figure 1.

3. Secure pump to stable structure to avoid tipping, using four (4) holes on outer

edge of standard foot mount. See Figure 2.

Motor Attachment

4. The Series SLA drive is designed to support up to an 85lbf (378N)

motor.

5. Install coupling hub with key to motor shaft and tighten the set

screw.

6. Align the motor side coupling with the factory Series SLA coupling

hub, with the elastomer spider inserted.

7. Align the motor flange with the Series SLA adapter flange and secure

by installing four (4) bolts (not included) sized according to the motor

frame.

8. Connect motor to electrical service with overcurrent protection and

means to safely interrupt power, following local rules and

regulations.

QUICK SETUP

www.cppumps.com

WARNING: Ensure that you are wearing proper PPE before performing any action.

Figure 2

Figure 1

Series SLA LeakLess

CP/DWG-ENG-006 REV. 01 EFF. DATE: 01/11/2023

Page 1 of 2

Pump Attachment

9. Connect the suction line to the suction port (see figure 4). Connect the discharge line to the discharge check valve. Line size

must be equal or greater than check valve connection. Liquid level should be equal to or higher than suction port. Open low

pressure bleeds 1 & 2 until all air is evacuated from pump head, (see Figure 3).

10. Open High Pressure bleed #1, while pump is running, until all air is evacuated from pump head, (see figure 4).

11. Always use an external pressure relief valve on the discharge side of the pump to protect from overpressure.

12. Fill gear casing with approximately 2.1qt (2.0L) oil to halfway mark on upper sight glass, (see Figure 5). Use Mobil SHC 634 or

equivalent.

Chemical Flow Rate Adjustment

13. Turn the adjustment knob to increase or

decrease the flow rate to the desired percentage,

as indicated by the markings. See Figure 6.

14. With fluid media present at the pump suction,

loosen the bleed screw and discharge line at the

discharge check outlet to vent to atmosphere.

Run the pump until all air trapped in the head is

released. Re-tighten the discharge line and bleed

screw.

15. Run a drawdown flow calibration. If the flow rate

is correct, stop here. If the flow rate is incorrect,

continue.

16. Turn the adjustment knob to increase or decrease

the flow rate as required, then repeat Step 14.

Suction

Discharge

Bleed

Figure 2

Figure 4

Figure 5

www.cppumps.com

Figure 3

CAUTION: Do not force handle during adjustment. Do not force below 0% or above 100% marks.

WARNING: Pump surfaces can become hot during operation. Wear protective gloves.

QUICK SETUP

Series SLA LeakLess

Figure 6

CP/DWG-ENG-006 REV. 01 EFF. DATE: 01/11/2023

Page 2 of 2

Andere Handbücher für SLA Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Checkpoint Wasserpumpe Handbücher

Checkpoint

Checkpoint 1250 Series Bedienungsanleitung

Checkpoint

Checkpoint ATP Series Bedienungsanleitung

Checkpoint

Checkpoint SLA Series Bedienungsanleitung

Checkpoint

Checkpoint ATP Series Technisches Datenblatt

Checkpoint

Checkpoint GX15G11C3 Series Bedienungsanleitung

Checkpoint

Checkpoint 6200 Series Bedienungsanleitung

Checkpoint

Checkpoint ATP3 Series Bedienungsanleitung

Checkpoint

Checkpoint 5400 Series Bedienungsanleitung

Checkpoint

Checkpoint 1250E Series Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

moyno

moyno 2000 CC Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung