Chicago Electric 38941 Stücklistenhandbuch

4’’ DRY TILE SAW

Model

38941

ASSEMBLY AND OPERATION INSTRUCTIONS

Due to continuing improvements, actual product may differ slightly from the product described herein.

Distributed Exclusively by Harbor Freight Tools

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our website at: http://www.harborfreight.com

TO PREVENT SERIOUS INJURY, READ AND UNDERSTAND

ALL WARNINGS AND INSTRUCTIONS BEFORE USE.

manual or any artwork contained herein may be reproduced in any shape or form without

the express written consent of Harbor Freight Tools.

For technical questions or replacement parts, please call 1-800-444-3353.

Diamond Blade not included; sold separately.

REV 09e

Page 2SKU 38941 For technical questions, please call 1-800-444-3353.

SPECIFICATIONS

Motor 110 V~, 3.2 A (No Load)

RPM 10,525

Cutting Capacity 1-3/8”

Blade (sold separately) 4” Diameter x 5/8” Arbor

Overall Dimensions 9” x 7” x 7-3/4”

Overall Weight 7.6 lb.

Motor is double insulated

The Tile Saw comes with an Arbor wrench and a T-Handle Wrench. A Blade is not included

with the Tile Saw and must be purchased separately. Recommended saw blade is item #34441

- 4” Diamond blade-Dry type. Saw blades are available at Harbor Freight Tools.

Save This Manual

You will need this manual for the safety warnings and precautions, assembly, operating,

inspection, maintenance and cleaning procedures, parts list and assembly diagram. Keep your

invoice with this manual. Write the invoice number on the inside of the front cover. Write the

product’s serial number in the back of the manual near the assembly diagram, or write month

and year of purchase if product has no number. Keep this manual and invoice in a safe and dry

place for future reference.

Wet Cut Attachment

A Wet Cut Attachment (Item 38942) is also available through Harbor Freight Tools. This

attachment is not included with the Dry Tile Saw.

If you have purchased the Wet Cut Attachment (#38942) please see the assembly and

operating instructions for this attachment on page #8. Recommended blade when using the Wet

Cut attachment is item #34310 - 4” Diamond blade-Wet type (Continuous Rim Design).

GENERAL SAFETY RULES

WARNING!

READ AND UNDERSTAND ALL INSTRUCTIONS

Failure to follow all instructions listed below may result in

electric shock, re, and/or serious injury.

SAVE THESE INSTRUCTIONS

WORK AREA

1. Keep your work area clean and well lit. Cluttered benches and dark areas invite ac-

cidents.

REV 08/01; 09e

#230373

Page 3SKU 38941 For technical questions, please call 1-800-444-3353.

2. Do not operate power tools in explosive atmospheres, such as in the presence of

ammable liquids, gases, or dust. Power tools create sparks which may ignite the dust

or fumes.

3. Keep bystanders, children, and visitors away while operating a power tool. Distrac-

tions can cause you to lose control. Protect others in the work area from debris such as

chips and sparks. Provide barriers or shields as needed.

ELECTRICAL SAFETY

1. Double insulated tools are equipped with a polarized plug (one blade is wider than

the other). This plug will t in a polarized outlet only one way. If the plug does

not t fully in the outlet, reverse the plug. If it still does not t, contact a qualied

electrician to install a polarized outlet. Do not change the plug in any way. Double

insulation eliminates the need for the three wire grounded power cord and grounded

power supply system.

2. Avoid body contact with grounded surfaces such as pipes, radiators, ranges, and

refrigerators. There is an increased risk of electric shock if your body is grounded.

3. Do not expose power tools to rain or wet conditions. Water entering a power tool will

increase the risk of electric shock. Only use correct wet cut attachment for wet cutting.

4. Do not abuse the Power Cord. Never use the Power Cord to carry the tools or pull

the Plug from an outlet. Keep the Power Cord away from heat, oil, sharp edges, or

moving parts. Replace damaged Power Cords immediately. Damaged Power Cords

increase the risk of electric shock.

5. When operating a power tool outside, use an outdoor extension cord marked “W-A”

or “W”. These extension cords are rated for outdoor use, and reduce the risk of electric

shock.

PERSONAL SAFETY

1. Stay alert. Watch what you are doing, and use common sense when operating a

power tool. Do not use a power tool while tired or under the inuence of drugs,

alcohol, or medication. A moment of inattention while operating power tools may result

in serious personal injury.

2. Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your

hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair

can be caught in moving parts.

3. Avoid accidental starting. Be sure the Power Switch is off before plugging in. Car-

rying power tools with your nger on the Power Switch, or plugging in power tools with the

Power Switch on, invites accidents.

4. Remove adjusting keys or wrenches before turning the power tool on. A wrench or a

key that is left attached to a rotating part of the power tool may result in personal injury.

Page 4SKU 38941 For technical questions, please call 1-800-444-3353.

5. Do not overreach. Keep proper footing and balance at all times. Proper footing and

balance enables better control of the power tool in unexpected situations.

6. Use safety equipment. Always wear eye protection. Dust mask, nonskid safety shoes,

hard hat, or hearing protection must be used for appropriate conditions. Always wear

ANSI-approved safety goggles and a dust mask/respirator when using or performing

maintenance on this tool.

TOOL USE AND CARE

1. Use clamps (not included) or other practical ways to secure and support the work-

piece to a stable platform. Holding the work by hand or against your body is unstable

and may lead to loss of control.

2. Do not force the tool. Use the correct tool for your application. The correct tool will

do the job better and safer at the rate for which it is designed. Do not force the tool and

do not use the tool for a purpose for which it is not intended.

3. Do not use the power tool if the Power Switch does not turn it on or off. Any tool that

cannot be controlled with the Power Switch is dangerous and must be replaced.

4. Disconnect the Power Cord Plug from the power source before making any adjust-

ments, changing accessories, or storing the tool. Such preventive safety measures

reduce the risk of starting the tool accidentally. Always unplug the tool from its electrical

outlet before performing any inspection, maintenance, or cleaning procedures.

5. Store idle tools out of reach of children and other untrained persons. Tools are dan-

gerous in the hands of untrained users.

6. Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained

tools with a sharp cutting edge are less likely to bind and are easier to control. Do not use

a damaged tool. Tag damaged tools “Do not use” until repaired.

7. Check for misalignment or binding of moving parts, breakage of parts, and any other

condition that may affect the tool’s operation. If damaged, have the tool serviced

before using. Many accidents are caused by poorly maintained tools.

8. Use only accessories that are recommended by the manufacturer for your model.

Accessories that may be suitable for one tool may become hazardous when used on an-

other tool.

SERVICE

1. Tool service must be performed only by qualied repair personnel. Service or main-

tenance performed by unqualied personnel could result in a risk of injury.

2. When servicing a tool, use only identical replacement parts. Follow instructions

in the “Inspection, Maintenance, And Cleaning” section of this manual. Use of un-

authorized parts or failure to follow maintenance instructions may create a risk of electric

shock or injury.

Page 5SKU 38941 For technical questions, please call 1-800-444-3353.

SPECIFIC SAFETY RULES

1. Maintain labels and nameplates on the tool. These carry important information. If

unreadable or missing, contact Harbor Freight Tools for a replacement.

2. Maintain a safe working environment. Make sure there is adequate surrounding work-

space. Do not use this product in a damp or wet location.

3. Avoid unintentional starting. Make sure you are prepared to begin work before turning

on the tool.

4. Always keep the extension cord away from moving parts on the tool.

5. People with pacemakers should consult their physician(s) before using this product.

Electromagnetic elds in close proximity to a heart pacemaker could cause interference

to or failure of the pacemaker. In addition, people with pacemakers should adhere to the

following:

• Avoid operating power tools alone.

• Don’t use a power tool with the power switch locked on.

• If powered via a power cord be certain that the tool is properly grounded. A ground fault

interrupt (GFCI) system is also a good precaution. This inexpensive device is a good

safety measure because it prevents a sustained electrical shock.

• Properly maintain and inspect all tools before use to avoid electrical shock.

6. Never leave the tool unattended when it is plugged into an electrical outlet. Turn off

the tool, and unplug it from its electrical outlet before leaving.

7. WARNING: Some dust created by power sanding, sawing, grinding, drilling, and

other construction activities, contains chemicals known [to the State of California]

to cause cancer, birth defects or other reproductive harm. Some examples of these

chemicals are:

Lead from lead-based paints

Crystalline silica from bricks and cement or other masonry products

Arsenic and chromium from chemically treated lumber

Your risk from these exposures varies, depending on how often you do this type of work.

To reduce your exposure to these chemicals: work in a well ventilated area, and work with

approved safety equipment, such as those dust masks that are specially designed to lter

out microscopic particles. (California Health & Safety Code § 25249.5, et seq.)

Page 6SKU 38941 For technical questions, please call 1-800-444-3353.

GROUNDING

Outlets for 2-Prong Plug

DOUBLE INSULATED TOOLS: TOOLS WITH TWO PRONG PLUGS

1. Tools marked “Double Insulated” do not require grounding. They have a special double

insulation system which satises OSHA requirements and complies with the applicable

standards of Underwriters Laboratories, Inc., the Canadian Standard Association, and the

National Electrical Code. (See Outlets for 2-Prong Plug.)

2. Double insulated tools may be used in either of the 120 volt outlets shown in the preceding

illustration. (See Outlets for 2-Prong Plug.)

EXTENSION CORDS

1. Double Insulated tools can use either a two or three wire extension cord.

2. As the distance from the supply outlet increases, you must use a heavier gauge extension

cord. Using extension cords with inadequately sized wire causes a serious drop in voltage,

resulting in loss of power and possible tool damage. (See Table A.)

3. The smaller the gauge number of the wire, the greater the capacity of the cord. For ex-

ample, a 14 gauge cord can carry a higher current than a 16 gauge cord.

(See Table A.)

4. When using more than one extension cord to make up the total length, make sure each

cord contains at least the minimum wire size required. (See Table A.)

5. If you are using one extension cord for more than one tool, add the nameplate amperes

and use the sum to determine the required minimum cord size.

(See Table A.)

6. If you are using an extension cord outdoors, make sure it is marked with the sufx “W-A”

(“W” in Canada) to indicate it is acceptable for outdoor use.

7. Make sure your extension cord is properly wired and in good electrical condition. Always

replace a damaged extension cord or have it repaired by a qualied electrician before

using it.

Page 7SKU 38941 For technical questions, please call 1-800-444-3353.

8. Protect your extension cords from sharp objects, excessive heat, and damp or wet ar-

eas.

RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS*

(120 OR 240 VOLT)

NAMEPLATE

AMPERES

(at full load)

EXTENSION CORD LENGTH

25 Feet 50 Feet 75 Feet 100 Feet 150 Feet

0 – 2.0 18 18 18 18 16

2.1 – 3.4 18 18 18 16 14

3.5 – 5.0 18 18 16 14 12

5.1 – 7.0 18 16 14 12 12

7.1 – 12.0 18 14 12 10 -

12.1 – 16.0 14 12 10 - -

16.1 – 20.0 12 10 - - -

TABLE A * Based on limiting the line voltage drop to ve volts at 150% of the rated amperes.

SYMBOLOGY

Double Insulated

Canadian Standards Association

Underwriters Laboratories, Inc.

V~ Volts Alternating Current

AAmperes

n0xxxx/min. No Load Revolutions per Minute (RPM)

Note: Performance of this tool may vary depending on variations in local line voltage. Extension

cord usage may also affect tool performance.

UNPACKING

When unpacking your Tile Saw make sure that the item is intact and undamaged. If any

parts are missing or broken, please call HARBOR FREIGHT TOOLS at 1-800-444-3353.

Page 8SKU 38941 For technical questions, please call 1-800-444-3353.

MAINTENANCE

1. Always keep the Saw clean. The ventilation passage should be kept clean and free from

obstructions.

2. Replacing Carbon Brushes:

a. Replace the Carbon Brushes when they wear down to about 3/16” or sparking will oc-

cur. Always change both brushes (43) (upper and lower) at the same time.

b. Using a at tip screwdriver, unscrew (counter-clockwise) the Brush Caps (Black plastic

plug) (44) on the Enclosure (36). Remove them from the Brush Holders (42).

c. Replace the Carbon Brushes with identical replacement parts from Harbor Freight Tools.

Insert the Brushes into the Brush Holder, and insert back into the Enclosure. Screw

back in the Brush Cap and tighten.

OPERATION

Installing and Removing the Cutting Blade

1. Your Tile Saw comes with an arbor wrench and a T-Handle socket wrench for use when

installing or removing a Blade. When installing or removing a blade, always make sure

the tool is OFF and unplugged.

2. A Diamond Cutting Blade is not included with the Tile Saw and must be purchased

separately.

3. Turn the Tile Saw so that you are looking at the Blade wheel. Place the arbor wrench

(58) on the Outside Flange (2) to hold the ange in place while using the socket wrench

(59) to loosen the Hex Bolt. Remove the Blade by sliding it up and off of the Spindle (8).

When mounting the blade, observe the rotation direction arrows, and slide the blade onto

the Spindle making sure that it ts snugly. Refer to the Blade manufacturer’s guidelines

for specications, proper use and warnings. With blade in place, hold Outside Flange in

place while tightening the Hex Bolt.

Using the Saw

1. Grip the Handle (30) with your index nger on the trigger switch and depress the trigger

switch to start the saw.

2. Apply rm and steady pressure to the Saw during use. DO NOT FORCE SAW.

Note: The Saw has a HOLD BUTTON to maintain constant speed and reduce fatigue. To lock

this button into the ON position, depress the Trigger Switch then press the Hold Button and

release pressure on the Trigger Switch. To RELEASE the HOLD BUTTON, lightly depress

the Trigger Switch.

REV 09e

Page 9SKU 38941 For technical questions, please call 1-800-444-3353.

PARTS LIST

Part Description Quantity

1 Hex Bolt 1

2 Outside Flange 1

3 Inside Flange 1

4 Screw M4 x 8 3

5 Elastic Washer 4 3

6 Bearing Cover 1

7 O Sealing Ring 1

8 Spindle 1

9 Woodruff Key 3 x 13 1

10 Bearing 1

11 Elastic Distance Ring 1

12 Screw M4 x 25 4

13 Elastic Washer -4 4

14 Gear Box Cover 1

15 No. 2 Gear 1

16 Needle Bearing 1

17 Middle Cover 1

18 No. 1 Gear 1

19 Bearing 1

20 Woodruff Key 2.5 x 10 1

21 Fan 1

22 Armature 1

23 Distance Ring 1

24 Bearing 1

25 Screw 5x65 2

26 Spring Washer - 5 2

27 Stator 1

28 Washer 1

29 O Sealing Ring 1

30 Handle Cover 1

Part Description Quantity

31 Air Guide 1

32 Screw 4 x 16 1

33 Cord Cup 1

34 Switch Sleeve 1

35 Switch 1

36 Enclosure 1

37 Screw 4 x 20 4

38 Nameplate 1

39 Washer 5 3

40 Spring washer 5 3

41 Screw M5 x 40 3

42 Brush holder 2

43 Brush 2

44 Brush cap 2

45 Cord 1

46 Cord armor 1

47 Base 1

48 Thumb bolt 1

49 Spring washer 1

50 Washer 1

51 Clip 1

52 Water tube 1

53 Elastic pin 6 x 30 1

54 Distance ring 1

55 Thumb bolt 1

56 PVC tube 1

57 Adapter 1

58 Wrench 1

59 Socket wrench 1

501 Blade/ not included 0

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEM-

BLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER

OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER

THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR

SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER

AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS

SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE

BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS

TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS

OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Page 10SKU 38941 For technical questions, please call 1-800-444-3353.

Record Product’s Serial Number Here:

Note: If product has no serial number, record month and year of purchase instead.

Note: Some parts are listed and shown for illustration purposes only, and are not available indi-

vidually as replacement parts.

Inhaltsverzeichnis

Andere Chicago Electric Gesehen Handbücher

Chicago Electric

Chicago Electric 98058 Installationshandbuch

Chicago Electric

Chicago Electric 98265 Installationshandbuch

Chicago Electric

Chicago Electric 91757 Bedienungsanleitung

Chicago Electric

Chicago Electric 96635 Installationshandbuch

Chicago Electric

Chicago Electric 46737 Bedienungsanleitung

Chicago Electric

Chicago Electric 42818 Bedienungsanleitung

Chicago Electric

Chicago Electric 97200 Installationshandbuch

Chicago Electric

Chicago Electric 47840 Bedienungsanleitung

Chicago Electric

Chicago Electric 91938 Original Bedienungsanleitung

Chicago Electric

Chicago Electric 94596 Stücklistenhandbuch

Chicago Electric

Chicago Electric 14 Industrial Cut-off Saw 68104 Montageanleitung

Chicago Electric

Chicago Electric 41903 Kurzanleitung

Chicago Electric

Chicago Electric 98199 Bedienungsanleitung

Chicago Electric

Chicago Electric 69067 Montageanleitung

Chicago Electric

Chicago Electric 94245 Bedienungsanleitung

Chicago Electric

Chicago Electric 40315 Installationshandbuch

Chicago Electric

Chicago Electric 68988 Montageanleitung

Chicago Electric

Chicago Electric 97580 Installationshandbuch

Chicago Electric

Chicago Electric 69066 Bedienungsanleitung

Chicago Electric

Chicago Electric 95004 Installationshandbuch

Chicago Electric

Chicago Electric 91852 Bedienungsanleitung

Chicago Electric

Chicago Electric 1624 Installationshandbuch

Chicago Electric

Chicago Electric 66753 Benutzerhandbuch

Chicago Electric

Chicago Electric 91935 Bedienungsanleitung

Beliebte Gesehen Handbücher anderer Marken

RIDGID

RIDGID BS1400 Bedienungsanleitung

ATIKA

ATIKA BWS 400-2 Bedienungsanleitung

RGC

RGC FS20 Bedienungsanleitung

Makita

Makita M2300 Bedienungsanleitung

Optimum

Optimum OPTisaw CS 275 Bedienungsanleitung

Makita

Makita BPB180 Bedienungsanleitung

Stihl

Stihl MS 462 C-M Bedienungsanleitung

AEG

AEG TS 250 K Bedienungsanleitung

Meec tools

Meec tools 004665 Bedienungsanleitung

Makita

Makita LS1018L Bedienungsanleitung

Ryobi

Ryobi RCS1400 Bedienungsanleitung

DeWalt

DeWalt DCS391 Bedienungsanleitung

Sealey

Sealey SA72 Bedienungsanleitung

skilsaw

skilsaw SPT88 Montageanleitung

Urrea

Urrea SI810 Abmessungen und Installationsanleitung

EINHELL

EINHELL BKG 210/1 Bedienungsanleitung

Altrad

Altrad BELLE RANGER 450 Bedienungsanleitung

Porter-Cable

Porter-Cable 725 Bedienungsanleitung