Chicago Electric 91935 Bedienungsanleitung

8-1/4” COMPOUND SLIDE MITER SAW

Model 91935

ASSEMBLY AND OPERATING INSTRUCTIONS

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit ourWeb site at: http://www.harborfreight.com

TO PREVENT SERIOUS INJURY,

READ AND UNDERSTAND ALL WARNINGS

AND INSTRUCTIONS BEFORE USE.

manual or any artwork contained herein may be reproduced in any shape or form

without the express written consent of Harbor Freight Tools.

For technical questions or replacement parts, please call 1-800-444-3353.

REVISED MANUAL 04/05

SKU 91935 For technical questions, please call 1-800-444-3353 Page 2

PRODUCT SPECIFICATIONS

Item Description

Electrical Requirements 120 V / 60 Hz / 1800 Watts

11.8 AMPs Start Up / 4,600 RPM

Two Prong, Grounded, Power Cord Plug

Power Switch Type: Squeeze Type

Saw Blade (Included)

Diameter/Type

8-1/4” Diameter / 60 Tooth Carbide Tip

4,600 Minimum RPM

Spindle Size 5/8” Diameter

Crosscut Capacity 7-1/2” x 2-3/4” Vertical Cut @ 90°

1-1/4” Vertical Cut @ 45°

Miter Capacity 45° Left and Right

Bevel Capacity 0° - 45° Left

Positive Stops 0°, 15°, 22.5°, 30°, 45° Left and Right

Overall Table Size 16-3/4” x 5-1/8”

Overall Dimensions 25-3/8” L x 16-3/4” W x 20-3/8” H

Weight 27.3 Pounds

E105017

SAVE THIS MANUAL

You will need this manual for the safety warnings and precautions, assembly, operating,

inspection, maintenance and cleaning procedures, parts list and assembly diagram.

Keep your invoice with this manual. Write the invoice number on the inside of the front

cover. Keep this manual and invoice in a safe and dry place for future reference.

GENERAL SAFETY RULES

IMPORTANT SAFETY INSTRUCTIONS

WARNING!

READ AND UNDERSTAND ALL INSTRUCTIONS

Failure to follow all instructions listed in the following

pages may result in electric shock, fire, and/or serious injury.

SAVE THESE INSTRUCTIONS

1. Keep your work area clean and well lit. Cluttered benches and dark areas

invite accidents.

WORK AREA

2. Do not operate power tools in explosive atmospheres, such as in the

presence of flammable liquids, gases, or dust. Power tools create sparks

which may ignite flammables.

3. Keep bystanders, children, and visitors away while operating a power tool.

Distractions can cause you to lose control. Protect others in the work area from

debris such as chips and sparks. Provide barriers or shields as needed.

SKU 91935 For technical questions, please call 1-800-444-3353 Page 3

PERSONAL SAFETY

10. Stay alert. Watch what you are doing, and use common sense when

operating a power tool. Do not use a power tool while tired or under the

influence of drugs, alcohol, or medication. A moment of inattention while

operating power tools may result in serious personal injury.

11. Dress properly. Do not wear loose clothing or jewelry. Contain long hair.

Keep your hair, clothing, and gloves away from moving parts. Loose

clothes, jewelry, or long hair can be caught in moving parts.

12. Avoid accidental starting. Be sure the Power Switch is off before plugging

in. Carrying power tools with your finger on the Power Switch, or plugging in

power tools with the Power Switch on, invites accidents.

13. Remove adjusting keys or wrenches before turning the power tool on. A

wrench or a key that is left attached to a rotating part of the power tool may result

in personal injury.

4. Grounded tools must be plugged into an outlet properly installed and

grounded in accordance with all codes and ordinances. Never remove the

grounding prong or modify the plug in any way. Do not use any adapter

plugs. Check with a qualified electrician if you are in doubt as to whether

the outlet is properly grounded. If the tools should electrically malfunction or

break down, grounding provides a low resistance path to carry electricity away

from the user.

5. Double insulated tools are equipped with a polarized plug (one blade is

wider than the other). This plug will fit in a polarized outlet only one way. If

the plug does not fit fully in the outlet, reverse the plug. If it still does not

fit, contact a qualified electrician to install a polarized outlet. Do not

change the plug in any way. Double insulation eliminates the need for the

three wire grounded power cord and grounded power supply system.

6. Avoid body contact with grounded surfaces such as pipes, radiators,

ranges, and refrigerators. There is an increased risk of electric shock if your

body is grounded.

7. Do not expose power tools to rain or wet conditions. Water entering a power

tool will increase the risk of electric shock.

8. Do not abuse the Power Cord. Never use the Power Cord to carry the tools

or pull the Plug from an outlet. Keep the Power Cord away from heat, oil,

sharp edges, or moving parts. Replace damaged Power Cords immediately.

Damaged Power Cords increase the risk of electric shock.

9. When operating a power tool outside, use an outdoor extension cord

marked “W-A” or “W”. These extension cords are rated for outdoor use, and

reduce the risk of electric shock.

ELECTRICAL SAFETY

SKU 91935 For technical questions, please call 1-800-444-3353 Page 4

14. Do not overreach. Keep proper footing and balance at all times. Proper

footing and balance enables better control of the power tool in unexpected

situations.

15. Use safety equipment. Always wear eye protection. Dust mask, nonskid

safety shoes, hard hat or hearing protection must be used for appropriate

conditions.

TOOL USE AND CARE

16. Use clamps or other practical ways to secure and support the workpiece to

a stable platform. Holding the work by hand is unstable and may lead to loss of

control. Only work on a workpiece that is properly secured.

17. Do not force the tool. Use the correct tool for your application. The correct

tool will do the job better and safer at the rate for which it is designed.

18. Do not use the power tool if the Power Switch does not turn it on or off.

Any tool that cannot be controlled with the Power Switch is dangerous and must

be replaced.

19. Disconnect the Power Cord Plug from the power source before making any

adjustments, changing accessories, or storing the tool. Such preventive

safety measures reduce the risk of starting the tool accidentally.

20. Store idle tools out of reach of children and other untrained persons. Tools

are dangerous in the hands of untrained users.

21. Maintain tools with care. Keep cutting tools sharp and clean. Properly

maintained tools with a sharp cutting edge are less likely to bind and are easier to

control. Do not use a damaged tool. Tag damaged tools “Do not use” until

repaired.

22. Check for misalignment or binding of guards and other moving parts,

breakage of parts, cracking or breakage of the Saw Blade, and any other

condition that may affect the tool’s operation. If damaged, have the tool

serviced before using. Many accidents are caused by poorly maintained tools.

23. Use only accessories that are recommended by the manufacturer for your

model. Accessories that may be suitable for one tool may become hazardous

when used on another tool.

SERVICE

24. Tool service must be performed only by qualified repair personnel. Service

or maintenance performed by unqualified personnel could result in a risk of injury.

25. When servicing a tool, use only identical replacement parts. Follow

instructions in the

“Inspection, Maintenance, And Cleaning”

section of this

manual. Use of unauthorized parts or failure to follow maintenance instructions

may create a risk of electric shock or injury.

SKU 91935 For technical questions, please call 1-800-444-3353 Page 5

SPECIFIC SAFETY RULES

1. Maintain a safe working environment. Keep the work area well lit. Make sure

there is adequate surrounding workspace. Always keep the work area free of

obstructions, grease, oil, trash, and other debris. Do not use the Miter Saw in

areas near flammable chemicals, dusts, and vapors. Do not use this product in a

damp or wet location.

2. Maintain labels and nameplates on the Miter Saw. These carry important

information. If unreadable or missing, contact Harbor Freight Tools for a

replacement.

3. Do not force the equipment. This Miter Saw will do the work better and safer

at the speed and capacity for which it was designed.

4. Keep all guards in place and in working order. Never remove or disable guards.

5. Remove all adjusting wrenches from the Miter Saw before turning it on.

6. Do not abuse the Power Cord. Do not use the Power Cord to pull its Plug from

an electrical outlet. Keep the Power Cord away from heat, oil, sharp edges, and

moving parts. Route the Power Cord safely. Protect the Power Cord from being

damaged by other equipment in the work area. Do not route the Power Cord

where it can be walked on or tripped over. Replace a damaged Power Cord

immediately.

7. Do not use this Miter Saw for cutting metals or brittle materials. Do not cut

dangerous materials, such as asbestos which can cause harmful dust or vapors.

8. When replacing the Saw Blade, make sure the new Saw Blade has a

diameter of 8-1/4”, an RPM rating of at least 4600, and has an arbor hole of

5/8” diameter.

9. To avoid accidental injury, always wear heavy duty work gloves

when changing a Saw Blade.

10. Before using the Miter Saw, make sure the Saw Blade is properly mounted

on the Saw Spindle. Make sure the Saw Blade is balanced, and is not cracked

or bent.

11. The Saw Blade will become hot while cutting. Allow the Saw Blade to

completely cool before touching.

12. Make sure the workpiece is free from nails and any other foreign objects

which can damage the Saw Blade.

13. Keep your body positioned to either side of the Saw Blade, but not in

line with the Saw Blade. “Kickback” can cause the Saw to jump backwards.

14. Causes and operator prevention of “kickback”: Kickback is a sudden reaction

to a pinched, bound, or misaligned Saw Blade, causing an uncontrolled Saw to

lift up and out of the workpiece toward the operator. When the Saw Blade is

pinched or bound tightly by the kerf closing down, the Saw Blade stalls and the

Motor reaction drives the tool rapidly toward the operator. If the Saw Blade

SKU 91935 For technical questions, please call 1-800-444-3353 Page 6

C. When restarting the Saw in the workpiece, center the Saw Blade in

the kerf and check that the saw teeth are not engaged into the

workpiece. If the Saw Blade is binding, it may walk up or kickback from the

workpiece as the Saw is restarted.

D. Support large panels to minimize the risk of Saw Blade pinching and

kickback. Large panels tend to sag under their own weight. Supports must

be placed under the panel on both sides, near the line of cut and near the

edge of the panel.

E. Do not use a dull or damaged Saw Blade. Unsharpened or improperly

set Saw Blades produce a narrow kerf causing excessive friction, Saw Blade

binding and kickback.

F. Make sure all Saw adjustments are tight and secure before making a cut.

If Saw adjustments shift while cutting, it may cause binding and kickback.

15. WARNING! The Lock Pin Knob (35) should always be activated in the

“locked down” position when the Saw is not being used and when the Saw

is being transported. The Lock Pin Knob should be activated in the

“locked up” position when changing Saw Blades. NEVER use the Lock Pin

Knob in any cutting operation. The Locks Pin Knob allows the operator to

lock the Saw Blade in position, preventing the Saw Blade from being raised or

lowered.

16. Allow the Saw Blade to spin up to full speed before feeding it into the

workpiece. Do not force the Saw Blade into the workpiece when cutting. Apply

moderate pressure, allowing the Saw Blade to cut without being forced. When

turning off the Saw, allow the Saw Blade to spin down and stop on its own. Do

not press against the Saw Blade to stop it.

A. Maintain a firm grip with both hands on the Saw, and position your body

and arm to allow you to resist kickback forces.

B. When the Saw Blade is binding, or when interrupting a cut for any

reason, release the Power Switch and hold the Saw motionless in

the workpiece until the Saw Blade comes to a complete stop. Never

attempt to remove the Saw Blade from the workpiece or pull the Saw

backward while the Saw Blade is in motion or kickback can occur.

becomes twisted or misaligned in the cut, the teeth at the back edge of the Saw

Blade can dig into the top surface of the workpiece, causing the Saw Blade to

climb out of the kerf and jump toward the operator. Kickback is a result of tool

misuse and/or incorrect operating procedures or conditions and can be

minimized by taking proper precautions as given below:

SKU 91935 For technical questions, please call 1-800-444-3353 Page 7

17. Turn off the Saw and allow the Saw Blade to stop on its own if the Saw

Blade is to be backed out of an uncompleted cut.

18. Industrial applications must follow OSHA requirements.

19. Never attempt to remove material stuck in the moving parts of the Miter

Saw while the machine is plugged in and running.

20. Whenever possible, use clamps or other safe, practical ways to hold and

support the workpiece. Do not attempt to cut material that does not have a flat

surface, unless a suitable support is used.

21. Always keep hands and fingers away from the spinning Saw Blade.

22. Use eye, hearing, and breathing protection. Always wear ANSI approved

safety impact eye goggles, hearing protectors, and dust masks or respirator

when working with the Miter Saw.

23. Do not use this product if under the influence of alcohol or drugs. Read

warning labels on prescriptions to determine if your judgement or reflexes are

impaired while taking drugs. If there is any doubt, do not attempt to use this

product.

24. Maintain this product with care. Keep the Miter Saw clean and dry for better

and safer performance. For your safety, service and maintenance should be

performed regularly by a qualified technician.

25. Use the right tool or attachment for the right job. Do not attempt to force a

small tool or attachment to do the work of a larger industrial tool or attachment.

There are certain applications for which this product was designed. It will do the

job better and more safely at the rate for which it was intended. Do not modify

this product, and do not use this product for a purpose for which it was not

intended.

26. Always turn off the Miter Saw and unplug the Power Cord from its electrical

outlet before changing accessories or performing inspection, maintenance,

or cleaning procedures.

27. Keep children out of the work area. Never allow children to play with tools.

Always lock and secure the work area.

28. WARNING! People with pacemakers should consult their physician(s)

before using this product. Operation of electrical equipment in close proximity to

a heart pacemaker could cause interference or failure of the pacemaker.

SKU 91935 For technical questions, please call 1-800-444-3353 Page 8

29. WARNING! Some dust created by power sanding, sawing, grinding, drilling,

and other construction activities, contain chemicals known (to the State of

California) to cause cancer, birth defects or other reproductive harm. Some

examples of these chemicals are: lead from lead-based paints, crystalline silica

from bricks and cement or other masonry products, arsenic and chromium from

chemically treated lumber. Your risk from these exposures varies, depending on

how often you do this type of work. To reduce your exposure to these chemicals:

work in a well ventilated area, and work with approved safety equipment, such as

those dust masks that are specially designed to filter out microscopic particles.

(California Health & Safety Code 25249.5, et seq.)

30. WARNING! The warnings, precautions, and instructions discussed in this

manual cannot cover all possible conditions and situations that may occur. The

operator must understand that common sense and caution are factors which

cannot be built into this product, but must be supplied by the operator.

GROUNDING

Improperly connecting the grounding wire can result in the risk of electric shock.

Check with a qualified electrician if you are in doubt as to whether the outlet is

properly grounded. Do not modify the power cord plug provided with the tool. Never

remove the grounding prong from the plug. Do not use the tool if the power cord or

plug is damaged. If damaged, have it repaired by a service facility before use. If the

plug will not fit the outlet, have a proper outlet installed by a qualified electrician.

GROUNDED TOOLS: TOOLS WITH THREE PRONG PLUGS

1. Tools marked with “Grounding Required” have a three wire cord and three prong

grounding plug. The plug must be connected to a properly grounded outlet. If

the tool should electrically malfunction or break down, grounding provides a low

resistance path to carry electricity away from the user, reducing the risk of electric

shock. (See Figure A.)

2. The grounding prong in the plug is connected through the green wire inside the

cord to the grounding system in the tool. The green wire in the cord must be the

only wire connected to the tool’s grounding system and must never be attached

to an electrically “live” terminal. (See Figure A.)

3. Your tool must be plugged into an appropriate outlet, properly installed and

grounded in accordance with all codes and ordinances. The plug and outlet

should look like those in the following illustration. (See Figure A.)

WARNING!

FIGURE A

SKU 91935 For technical questions, please call 1-800-444-3353 Page 9

DOUBLE INSULATED TOOLS: TOOLS WITH TWO PRONG PLUGS

4. Tools marked with “Double Insulated” do not require grounding. They have a

special double insulation system which satisfies OSHA requirements and

complies with the applicable standards of Underwriters Laboratories, Inc., the

Canadian Standard Association, and the National Electric Code. (See Figure B.)

5. Double insulated tools may be used in either of the 120 volt outlets shown in the

following illustration. (See Figure B.)

FIGURE B

SKU 91935 For technical questions, please call 1-800-444-3353 Page 10

Double Insulated

tools can use either a two or three wire extension cord.

2. As the distance from the supply outlet increases, you must use a heavier gauge

extension cord. Using extension cords with inadequately sized wire causes a

serious drop in voltage, resulting in loss of power and possible tool damage.

(See Figure C.)

3. The smaller the gauge number of the wire, the greater the capacity of the cord.

For example, a 14 gauge cord can carry a higher current than a 16 gauge cord.

(See Figure C.)

4. When using more than one extension cord to make up the total length, make

sure each cord contains at least the minimum wire size required.

(See Figure C.)

5. If you are using one extension cord for more than one tool, add the nameplate

amperes and use the sum to determine the required minimum cord size.

(See Figure C.)

6. If you are using an extension cord outdoors, make sure it is marked with the suffix

“W-A” (“W” in Canada) to indicate it is acceptable for outdoor use.

7. Make sure your extension cord is properly wired and in good electrical condition.

Always replace a damaged extension cord or have it repaired by a qualified

electrician before using it.

8. Protect your extension cords from sharp objects, excessive heat, and damp or wet

areas.

RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS*

(120 VOLT)

NAMEPLATE

AMPERES

(At Full Load)

EXTENSION CORD LENGTH

FEET

100

FEET

150

FEET

0-2.0 18 18 18 18 16

2.1-3.4 18 18 18 16 14

3.5-5.0 18 18 16 14 12

5.1-7.0 18 16 14 12 12

7.1-12.0 16 14 12 10 -

12.1-16.0 14 12 10 - -

16.1-20.0 12 10 - - -

*Based on limiting the line voltage drop

to five volts at 150% of the rated amperes.

FIGURE C

EXTENSION CORDS

Inhaltsverzeichnis

Andere Chicago Electric Gesehen Handbücher

Chicago Electric

Chicago Electric 69702 Montageanleitung

Chicago Electric

Chicago Electric 91995 Installationshandbuch

Chicago Electric

Chicago Electric 68819 Bedienungsanleitung

Chicago Electric

Chicago Electric Professional Series 60608 Bedienungsanleitung

Chicago Electric

Chicago Electric 56776 Montageanleitung

Chicago Electric

Chicago Electric 92386 Stücklistenhandbuch

Chicago Electric

Chicago Electric 46737 Bedienungsanleitung

Chicago Electric

Chicago Electric 41168 Betriebsanleitung

Chicago Electric

Chicago Electric 95004 Bedienungsanleitung

Chicago Electric

Chicago Electric 61884 Montageanleitung

Chicago Electric

Chicago Electric 96697 Installationshandbuch

Chicago Electric

Chicago Electric 91938 Original Bedienungsanleitung

Chicago Electric

Chicago Electric 96698 Installationshandbuch

Chicago Electric

Chicago Electric 69067 Montageanleitung

Chicago Electric

Chicago Electric 62800 Montageanleitung

Chicago Electric

Chicago Electric 42597 Handbuch

Chicago Electric

Chicago Electric 14 Industrial Cut-off Saw 68104 Montageanleitung

Chicago Electric

Chicago Electric 61608 Bedienungsanleitung

Chicago Electric

Chicago Electric 40315 Installationshandbuch

Chicago Electric

Chicago Electric 04042 Bedienungsanleitung

Chicago Electric

Chicago Electric 69683 Montageanleitung

Chicago Electric

Chicago Electric 97200 Installationshandbuch

Chicago Electric

Chicago Electric 98058 Installationshandbuch

Chicago Electric

Chicago Electric 47840 Montageanleitung

Beliebte Gesehen Handbücher anderer Marken

RIDGID

RIDGID BS1400 Bedienungsanleitung

ATIKA

ATIKA BWS 400-2 Bedienungsanleitung

RGC

RGC FS20 Bedienungsanleitung

Makita

Makita M2300 Bedienungsanleitung

Optimum

Optimum OPTisaw CS 275 Bedienungsanleitung

Makita

Makita BPB180 Bedienungsanleitung

Stihl

Stihl MS 462 C-M Bedienungsanleitung

AEG

AEG TS 250 K Bedienungsanleitung

Meec tools

Meec tools 004665 Bedienungsanleitung

Makita

Makita LS1018L Bedienungsanleitung

Ryobi

Ryobi RCS1400 Bedienungsanleitung

DeWalt

DeWalt DCS391 Bedienungsanleitung

Sealey

Sealey SA72 Bedienungsanleitung

skilsaw

skilsaw SPT88 Montageanleitung

Urrea

Urrea SI810 Abmessungen und Installationsanleitung

EINHELL

EINHELL BKG 210/1 Bedienungsanleitung

Altrad

Altrad BELLE RANGER 450 Bedienungsanleitung

Porter-Cable

Porter-Cable 725 Bedienungsanleitung