Chicago Electric 92386 Stücklistenhandbuch

7” 1.5 HP TILE SAW

WITH STAND

92386

ASSEMBLY AND OPERATION INSTRUCTIONS

Due to continuing improvements, actual product may differ slightly from the product described herein.

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our website at: http://www.harborfreight.com

TO PREVENT SERIOUS INJURY, READ AND UNDERSTAND

ALL WARNINGS AND INSTRUCTIONS BEFORE USE.

manual or any artwork contained herein may be reproduced in any shape or form

without the express written consent of Harbor Freight Tools.

For technical questions or replacement parts, please call 1-800-444-3353.

SKU 92386 For technical questions, please call 1-800-444-3353. Page 2

PRODUCT SPECIFICATIONS

SAVE THIS MANUAL

You will need this manual for the safety warnings and precautions, assembly, operat-

ing, inspection, maintenance and cleaning procedures, parts list and assembly diagram.

Keep your invoice with this manual. Write the invoice number on the inside of the front

cover. Keep this manual and invoice in a safe and dry place for future reference.

GENERAL SAFETY RULES

WARNING!

READ AND UNDERSTAND ALL INSTRUCTIONS

Failure to follow all instructions listed below may result in

electric shock, ﬁre, and/or serious injury.

SAVE THESE INSTRUCTIONS

UNPACKING

When unpacking, check to make sure all the parts shown on the Parts Lists on page

23 are included. If any parts are missing or broken, please call Harbor Freight Tools at

the number shown on the cover of this manual as soon as possible.

IMPORTANT SAFETY INSTRUCTIONS

E105017

REV 08/05; REV 12/06

Electrical Requirements 120 V / 60 Hz / 3550 RPM / 1.5 HP/ Single Phase

3-Prong Power Cord Plug / Power Cord Length: 9 Ft

Coolant Pump Type Submersible Fountain Pump w/Flow Adjustment / 246 GPH Capacity

Required Blade Size / Style 7” Diameter / Continuous Rim Diamond Blade / Minimum 3550 RPM

Maximum Cutting Depth 1” @ 90° / 1” @ 45°

Maximum Cutting Length 25-3/8”

Maximum Tile Size 24” x 24”

Saw Bevel Capacity 0° to 45° in 2.5° Increments – Left Tilt Only

Miter Gauge Capacity 0° to 45° in 1° Increments – Right Angles Only

Rip Fence Scale 0” to 8-1/4” in 1/8” Increments / 0mm to 21mm in 2mm Increments

Spindle Size 5/8”

Fence Type Fixed

Coolant Basin Capacity 4 Gallons

Basin Dimensions 15” W x 22-3/4” L x 3-1/8” H

Work Table Dimensions 18” W x 32-3/4” L

Overall Dimensions 18-1/4” W x 42-1/4” L x 47-1/2” H

Weight 89 Pounds

Accessories Arbor Nut Wrenches (Qty. 2) / 7” Diameter Saw Blade (Qty. 1)

SKU 92386 For technical questions, please call 1-800-444-3353. Page 3

WORK AREA

Keep your work area clean and well lit. Cluttered and dark work areas invite

accidents.

Do not operate power tools in explosive atmospheres, such as in the pres-

ence of ﬂammable liquids, gases, or dust. Power tools create sparks which may

ignite the dust or fumes.

Keep bystanders, children, and visitors away while operating a power tool.

Distractions can cause you to lose control.

ELECTRICAL SAFETY

Grounded tools must be plugged into an outlet properly installed and grounded

in accordance with all codes and ordinances. Never remove the grounding

prong or modify the plug in any way. Do not use any adapter plugs. Check

with a qualiﬁed electrician if you are in doubt as to whether the outlet is prop-

erly grounded. If the tool should electrically malfunction or break down, grounding

provides a low resistance path to carry electricity away from the user.

Avoid body contact with grounded surfaces such as pipes, radiators, ranges,

and refrigerators. There is an increased risk of electric shock if your body is

grounded.

Do not expose power tools to rain or wet conditions. Water entering a power

tool will increase the risk of electric shock.

Do not abuse the Power Cord. Never use the Power Cord to pull the Plug from

an outlet. Keep the Power Cord away from heat, oil, sharp edges, or moving

parts. Replace damaged Power Cords immediately. Damaged Power Cords

increase the risk of electric shock.

When operating a power tool outside, use an outdoor extension cord marked

“W-A” or “W”. These extension cords are rated for outdoor use, and reduce the

risk of electric shock.

PERSONAL SAFETY

Stay alert. Watch what you are doing, and use common sense when oper-

ating a power tool. Do not use a power tool while tired or under the inﬂuence

of drugs, alcohol, or medication. A moment of inattention while operating power

tools may result in serious personal injury.

Dress properly. Do not wear loose clothing or jewelry. Contain long hair.

Keep your hair, clothing, and gloves away from moving parts. Loose clothes,

jewelry, or long hair can be caught in moving parts.

SKU 92386 For technical questions, please call 1-800-444-3353. Page 4

Avoid accidental starting. Be sure the Power Switch is off before plugging in.

Plugging in power tools with the Power Switch on invites accidents.

Remove adjusting keys or wrenches before turning the power tool on. A

wrench or a key that is left attached to a rotating part of the power tool may result

in personal injury.

Do not overreach. Keep proper footing and balance at all times. Proper footing

and balance enables better control of the power tool in unexpected situations.

Use safety equipment. Always wear eye protection. Wear an ANSI approved

full face shield and non-skid safety shoes. ANSI approved hearing and breathing

protection must be used for appropriate conditions.

TOOL USE AND CARE

Use clamps (not included) or other practical ways to secure and support a

smaller workpiece to a stable platform. Holding the work by hand or against your

body is unstable and may lead to loss of control.

Do not force the tool. Use the correct tool for your application. The correct

tool will do the job better and safer at the rate for which it is designed.

Do not use the power tool if the Power Switch does not turn it on or off. Any

tool that cannot be controlled with the Power Switch is dangerous and must be

replaced.

Disconnect the Power Cord Plug from the power source before making any

adjustments, changing accessories, or storing the tool. Such preventive safety

measures reduce the risk of starting the tool accidentally.

Store idle tools out of reach of children and other untrained persons. Tools

are dangerous in the hands of untrained users.

Maintain tools with care. Keep tools clean. Properly maintained tools are easier

to control. Do not use a damaged tool. Tag damaged tools “Do not use” until re-

paired.

Check for misalignment or binding of moving parts, breakage of parts, and any

other condition that may affect the tool’s operation. If damaged, have the tool

serviced before using. Many accidents are caused by poorly maintained tools.

Use only accessories that are recommended by the manufacturer for your

model. Accessories that may be suitable for one tool may become hazardous

when used on another tool.

SKU 92386 For technical questions, please call 1-800-444-3353. Page 5

SERVICE

Tool service must be performed only by qualiﬁed repair personnel. Service or

maintenance performed by unqualiﬁed personnel could result in a risk of injury.

When servicing a tool, use only identical replacement parts. Follow instruc-

tions in the “Inspection, Maintenance, And Cleaning” section of this manual.

Use of unauthorized parts or failure to follow maintenance instructions may create

a risk of electric shock or injury.

GROUNDING

WARNING!

Improperly connecting the grounding wire can result in the risk of electric shock.

Check with a qualiﬁed electrician if you are in doubt as to whether the outlet is

properly grounded. Do not modify the power cord plug provided with the tool.

Never remove the grounding prong from the plug. Do not use the tool if the

power cord or plug is damaged. If damaged, have it repaired by a service facil-

ity before use. If the plug will not ﬁt the outlet, have a proper outlet installed by

a qualiﬁed electrician.

GROUNDED TOOLS: TOOLS WITH THREE PRONG PLUGS

Tools marked with “Grounding Required” have a three wire cord and three prong

grounding plug. The plug must be connected to a properly grounded outlet. If

the tool should electrically malfunction or break down, grounding provides a low

resistance path to carry electricity away from the user, reducing the risk of electric

shock. (See Figure A.)

WARNING: To reduce the risk of electroncution, keep all connections dry and off

the ground. Do not touch plug with wet hands. Ground Fault Circuit Interrupter

(GFCI) protection should be provided on the circuit(s) or outlet)s) to be used for the

tile saw (GFCI is not included in this machinery). Receptacles are available having

built-in GFCI protection and may be used for this measure of safety.

The grounding prong in the plug is connected through the green wire inside the

cord to the grounding system in the tool. The green wire in the cord must be the

only wire connected to the tool’s grounding system and must never be attached to

an electrically “live” terminal. (See Figure A.)

REV 12/06

SKU 92386 For technical questions, please call 1-800-444-3353. Page 6

REV 03/05

Your tool must be plugged into an appropriate outlet, properly installed and grounded

in accordance with all codes and ordinances. The plug and outlet should look like

those in the following illustration. (See Figure A.)

FIGURE A

EXTENSION CORDS

Grounded tools require a three wire extension cord. Double Insulated tools can

use either a two or three wire extension cord.

As the distance from the supply outlet increases, you must use a heavier gauge

extension cord. Using extension cords with inadequately sized wire causes a seri-

ous drop in voltage, resulting in loss of power and possible tool damage.

(See Figure B, next page.)

The smaller the gauge number of the wire, the greater the capacity of the cord. For

example, a 14 gauge cord can carry a higher current than a 16 gauge cord.

(See Figure B.)

When using more than one extension cord to make up the total length, make sure

each cord contains at least the minimum wire size required. (See Figure B.)

If you are using one extension cord for more than one tool, add the nameplate am-

peres and use the sum to determine the required minimum cord size.

(See Figure B.)

If you are using an extension cord outdoors, make sure it is marked with the sufﬁx

“W-A” (“W” in Canada) to indicate it is acceptable for outdoor use.

Make sure your extension cord is properly wired and in good electrical condition.

Always replace a damaged extension cord or have it repaired by a qualiﬁed electri-

cian before using it.

Protect your extension cords from sharp objects, excessive heat, and damp or wet

areas.

SKU 92386 For technical questions, please call 1-800-444-3353. Page 7

RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS*

(120 OR 240 VOLT)

NAMEPLATE

AMPERES

(at full load)

EXTENSION CORD LENGTH

25 Feet 50 Feet 75 Feet 100 Feet 150 Feet

0 – 2.0 18 18 18 18 16

2.1 – 3.4 18 18 18 16 14

3.5 – 5.0 18 18 16 14 12

5.1 – 7.0 18 16 14 12 12

7.1 – 12.0 18 14 12 10 -

12.1 – 16.0 14 12 10 - -

16.1 – 20.0 12 10 - - -

FIGURE B * Based on limiting the line voltage drop to ﬁve volts at 150% of the rated amperes.

SYMBOLOGY

Double Insulated

Canadian Standards Association

Underwriters Laboratories, Inc.

V~ Volts Alternating Current

AAmperes

n0xxxx/min. No Load Revolutions per Minute (RPM)

SKU 92386 For technical questions, please call 1-800-444-3353. Page 8

SPECIFIC SAFETY RULES

Maintain labels and nameplates on the Tile Saw. These carry important informa-

tion. If unreadable or missing, contact Harbor Freight Tools for a replacement.

Use the right product for the right job. There are certain applications for which

this product was designed. Do not use small equipment, tools, or attach-ments to

do the work of larger industrial equipment, tools, or attachments. Do not use this

product for a purpose for which it was not intended.

This product must continuously run with cold water. Dry running will cause

serious damage to the Pump seals.

WARNING! Keeps hands and ﬁngers away from cutting area and Saw Blade.

Use a “push stick” (not included) when necessary.

Check Blade Guard for proper forward/backward movement before each use.

Do not operate the Tile Saw if the Blade Guard does not move freely. Make sure

the Blade Guard moves freely and does not touch the Saw Blade or any other part

of the Saw, in all angles and depths of cut.

Do not handle the Power Switch with wet hands.

Make sure the Tile Saw is located on a ﬂat, level, sturdy surface capable of

supporting the weight of the Saw and work pieces.

Always use Diamond Saw Blades with a 7” diameter, 5/8” round arbor hole,

and rated at 3550 RPM or greater.

Use the Tile Saw only for cutting ceramic tile, quarry tile, marble, terra-cotta,

and slate with a maximum thickness of 1” if cutting at a 90 degree angle or 1”

if cutting at a 45 degree angle.

Do not use the Tile Saw for cutting metals or for cutting curves. This may

cause the Saw Blade to break and/or reduce it s service life.

Make sure the Saw Blade is wet at all times when cutting.

Keep all electrical connections dry and off the ground.

10.

11.

12.

REV 12/06

SKU 92386 For technical questions, please call 1-800-444-3353. Page 9

POWER CORD

120 VOLT,

GROUNDED

ELECTRICAL

OUTLET

TILE SAW

DRIP LOOP FIGURE C

Always arrange a “drip loop” in the Power Cord connecting the Tile Saw to a

120 volt, grounded, electrical outlet. A drip loop is that part of the Power Cord

below the level of the outlet, or the connector if an extension cord is used, to pre-

vent water traveling along the Power Cord and coming in contact with the outlet.

If the Power Plug or electrical outlet does get wet, do not unplug the Power Cord.

Disconnect the fuse or circuit breaker that supplies power to the tool. Then, unplug

and examine for presence of water in the outlet. (See Figure C.)

Use cold water only. Never use hot water. Using hot water can damage the

Pump seals.

Never run the Tile Saw without a water supply. Running the unit without a water

supply will cause irreparable damage to the Pump.

Make sure the water supply used for the Tile Saw is not dirty, sandy, and does

not contain any corrosive chemical products.

Make sure to change the water when necessary while in use and rinse out

the Tub after every use.

Never leave theTile Saw unattended when it is plugged into an electrical outlet.

Turn off the Tile Saw, and unplug it from its electrical outlet.

Always keep the water level at the recommended level. Fill the Tank with enough

water so that the Pump is about 3/4 completely submerged, but not so much water

that the Tank overﬂows.

Avoid splashing water on the Motor, Power Switch, Power Cord, or any other

electrical component. Make sure to stand on a dry, insulated surface such as a

rubber mat while using the Tile Saw.

To avoid accidental injury, always wear heavy duty work gloves when changing

the Saw Blade. Before using the Tile Saw, make sure the Saw Blade is properly

mounted on the Saw Spindle. Make sure the Saw Blade is balanced, and is not

cracked or bent.

13.

14.

15.

16.

17.

18.

19.

20.

21.

SKU 92386 For technical questions, please call 1-800-444-3353. Page 10

The Saw Blade will become hot while cutting. Allow the Saw Blade to com-

pletely cool before handling.

Allow the Saw Blade to spin up to full speed before feeding a workpiece into

it. When turning off the Tile Saw, allow the Saw Blade to spin down and stop on its

own. Do not press against the Saw Blade to stop it.

Do not force the workpiece into the Saw Blade when cutting. Apply moder-ate

pressure, allowing the Saw Blade to cut without being forced.

Turn off the Tile Saw and allow the Saw Blade to stop on its own if the Saw

Blade is to be backed out of an uncompleted cut.

Never attempt to remove material stuck in the moving parts of the Tile Saw

while it is plugged in and running.

When cutting a large workpiece make sure its entire length is properly sup-

ported. If necessary, use a roller stand (not included) with larger work pieces.

Never stand on the Tile Saw. Serious injury could result if the Tile Saw is tipped

or if the rotating Saw Blade is accidently contacted.

Industrial applications must follow OSHA requirements.

For your safety: In extreme working conditions, sensors in the Tile Saw will

automatically switch off the Motor to prevent overheating. In this event, turn

the Power Switch to its “OFF” position. Wait ﬁve minutes or until the Motor has

cooled. Making sure your hands are dry, depress the Circuit Breaker. Then, turn

the Power Switch to its “ON” position to resume cutting. NEVER attempt to dis-

able the Circuit Breaker.

Never attempt to cut more than one tile at a time.

Never attempt to cut freehand. Make sure the tile to be cut is pressed ﬁrmly

against the Rip Fence.

Never cut pieces too small to be held securely against the Rip Fence with-

out leaving enough space for the hand to be a safe distance from the Saw

Blade.

Make sure the tile to be cut off has sufﬁcient room to move sideways. Failure

to do so may result in the tile binding against the Saw Blade.

Make sure the Table and surrounding area are clear with the exception of the

tile to be cut.

Always turn off the Tile Saw and unplug it from its electrical outlet before

changing accessories or performing any inspection, maintenance, or clean-

ing procedures.

22.

23.

24.

25.

26.

27.

28.

29.

30.

31.

32.

33.

34.

35.

36.

Inhaltsverzeichnis

Andere Chicago Electric Gesehen Handbücher

Chicago Electric

Chicago Electric 40315 Bedienungsanleitung

Chicago Electric

Chicago Electric 68829 Montageanleitung

Chicago Electric

Chicago Electric 65298 Installationshandbuch

Chicago Electric

Chicago Electric 95004 Bedienungsanleitung

Chicago Electric

Chicago Electric 90186 Bedienungsanleitung

Chicago Electric

Chicago Electric 98058 Installationshandbuch

Chicago Electric

Chicago Electric 44829 Installationshandbuch

Chicago Electric

Chicago Electric 95004 Installationshandbuch

Chicago Electric

Chicago Electric 41168 Betriebsanleitung

Chicago Electric

Chicago Electric 42597 Handbuch

Chicago Electric

Chicago Electric 62800 Montageanleitung

Chicago Electric

Chicago Electric 37412 Bedienungsanleitung

Chicago Electric

Chicago Electric 1624 Installationshandbuch

Chicago Electric

Chicago Electric 44829 Bedienungsanleitung

Chicago Electric

Chicago Electric 91995 Installationshandbuch

Chicago Electric

Chicago Electric 61971 Montageanleitung

Chicago Electric

Chicago Electric POWER TOOL 94362 Bedienungsanleitung

Chicago Electric

Chicago Electric 94488 Bedienungsanleitung

Chicago Electric

Chicago Electric 67080 Installationshandbuch

Chicago Electric

Chicago Electric 42933 Bedienungsanleitung

Chicago Electric

Chicago Electric 61481 Montageanleitung

Chicago Electric

Chicago Electric 40315 Montageanleitung

Chicago Electric

Chicago Electric 02811 Bedienungsanleitung

Chicago Electric

Chicago Electric 96635 Installationshandbuch

Beliebte Gesehen Handbücher anderer Marken

RIDGID

RIDGID BS1400 Bedienungsanleitung

ATIKA

ATIKA BWS 400-2 Bedienungsanleitung

RGC

RGC FS20 Bedienungsanleitung

Makita

Makita M2300 Bedienungsanleitung

Optimum

Optimum OPTisaw CS 275 Bedienungsanleitung

Makita

Makita BPB180 Bedienungsanleitung

Stihl

Stihl MS 462 C-M Bedienungsanleitung

AEG

AEG TS 250 K Bedienungsanleitung

Meec tools

Meec tools 004665 Bedienungsanleitung

Makita

Makita LS1018L Bedienungsanleitung

Ryobi

Ryobi RCS1400 Bedienungsanleitung

DeWalt

DeWalt DCS391 Bedienungsanleitung

Sealey

Sealey SA72 Bedienungsanleitung

skilsaw

skilsaw SPT88 Montageanleitung

Urrea

Urrea SI810 Abmessungen und Installationsanleitung

EINHELL

EINHELL BKG 210/1 Bedienungsanleitung

Altrad

Altrad BELLE RANGER 450 Bedienungsanleitung

Porter-Cable

Porter-Cable 725 Bedienungsanleitung