CHIEF PLP Series Bedienungsanleitung

CHIEF MANUFACTURING INC. 8805-000141 (Rev. C)

8401 EAGLE CREEK PARKWAY, STE. 700 www.chiefmfg.com

SAVAGE, MINNESOTA 55378 USA 11/05

INSTALLATION INSTRUCTIONS

PLP Series Wall Mount

The PLP Series wall mount accommodates large flat

screens weighing up to 200 lbs (90.72kg). The teardrop

holes in the mount allow for quick connect/disconnect of

the screen, thus simplifying installation and maintenance

processes.

The top and bottom mounting brackets are adaptable to

supporting framework with wood studs that are 16” on

center or 24”on center.

The mount has integrated lateral shift, allowing for four

different mounting options. For dual wood studs 16” on

center, the lateral shift is +4.5 inches. For dual wood

studs 24” on center, the lateral shift is +0.5 inches.

The display can be pulled and tilted by hand into any

position in the zero-to-15 degree tilt range and remain

stationary.

The bottom of the mount pulls forward 3” from the wall

and locks into place for installation of cable connections.

The mount also uses Chief’s exclusive Q-Latch™

mounting system, which offers quick connect/disconnect

display mounting. The display is secured to the mount

with a latching flag. For additional security, you can lock

the latching flag in place by adding a padlock.

PLP Series

! IMPORTANT: If the installation of this product requires OSHPD seismic approval, refer to OSHPD pre-approval

documents and drawings before beginning installation. OSHPD documents and drawings are available at

www.chiefmfg.com, and located on the product information page for the mount.

BEFORE YOU BEGIN

•CAUTION: To prevent damage to your monitor and PLP, which could affect or void the Factory warranty,

thoroughly study all instructions and illustrations before you begin to install the mount. Pay particular

attention to the Warnings and Cautions in this document.

•The mount is designed to be installed using wall studs or supporting framework. The fasteners used to anchor the

mount must be capable of supporting five times the total weight of the equipment.

•The maximum weight to be installed on the PLP Series wall mount is 200 lbs (90.72kg).

•If you have any questions about this installation, contact Chief Manufacturing at 1-800-582-6480 or 952-582-6480.

Installation Instructions PLP Series

IMPORTANT WARNINGS and CAUTIONS!

WARNING A WARNING alerts you to the possibility of serious injury or death if you do not

follow the instructions.

CAUTION ACAUTION alerts you to the possibility of damage or destruction of equipment if you do

not follow the corresponding instructions.

•WARNING Improper installation can result in serious personal injury! Make sure that the

structural members can support a redundant weight factor five times the total weight

of the equipment. If not, reinforce the structure before installing the mount.

•WARNING Be aware of the potential for personal injury or damage to the equipment if it is not

installed correctly. Consider the weight of the mount without the display.

•WARNING The installer is responsible for verifying that the display to which the wall mount is

fastened will safely support the combined load of all attached components or other

equipment.

•WARNING The combined weight of the display placed on the wall mount must not exceed 200 lbs

(90.72kg), the maximum support weight of the mount.

•WARNING Watch for pinch points. Do not put your fingers between movable parts.

•WARNING Make sure the flag securing the display is completely lowered at all times except when

removing or installing the display. The flag must be all the way down when

installing/removing cables.

•CAUTION Check the unit for shipping damage before you begin the installation.

DIMENSIONAL DRAWING

Installation Instructions PLP Series

CONTENTS

DIMENSIONAL DRAWING........................................2

TOOLS REQUIRED FOR INSTALLATION...............3

PARTS LIST..................................................................3

PLP INSTALLATION...................................................4

Select Mounting Location ..........................................4

Mount the PLP............................................................5

ATTACH PSB TO THE DISPLAY ..............................6

INSTALL THE DISPLAY ............................................6

REMOVE THE DISPLAY............................................6

TILT ADJUSTMENT....................................................7

CABLE CONNECTION................................................7

TOOLS REQUIRED FOR

INSTALLATION

•Drill and drill bit set

•Socket wrench set

NOTE: Other tools may be required depending on your

method of installation.

Figure 1. PLP Parts

PARTS LIST

Prior to assembly, unpack the carton completely. Verify

contents listed in Table 1 and Figure 1.

Read installation instructions completely. If you are

missing any of the listed parts, contact Customer Service

at: 1-800/582-6480.

Table 1. Parts List

REF DESCRIPTION QTY

10 PLP Series Wall Mount 1

— BOLT, Lag, 5/16” x 2 ½” (required, not

supplied) 4

— WASHER, 5/16” (required, not supplied) 4

4 Lag Bolts

(Not supplied)

4 Washers

(Not supplied)

Installation Instructions PLP Series

PLP INSTALLATION

Perform the following procedures to mount the PLP.

Select Mounting Location

To select the mounting location, do the following:

WARNING: It is the responsibility of the installer to

verify that the wall to which the mount is

anchored will safely support the

combined load of all attached

components and equipment.

1. Determine the exact mounting location to install the

wall mount prior to installation, keeping in mind the

screen size.

NOTE: Mount the PLP on dual wall studs or some other

equivalent supporting framework that is vertical

or horizontal.

2. Using a stud sensor, locate the two wood studs where

you will mount the PLP as follows:

•Refer to Figure 3 for wood studs that are

16” apart on center.

•Refer to Figure 4 for wood studs that are

24” apart on center.

3. Using a nail as a temporary hook, hang the mount on

the wall using the triangular hole located in the center

of the mount (see Figure 2).

4. Use a pencil to mark the mounting holes where the

four pilot holes will be drilled into the center of the

wood stud. Make sure the mounting holes are square

and straight. Remove the mount from the wall,

placing it on the floor or a table.

5. Drill pilot holes using a 7/32” drill.

Figure 2. Use Triangular Hole to Hang the Mount

Figure 3. Wood Studs 16”Apart on Center

Figure 4. Wood Studs 24”Apart on Center

Wall Pilot Holes

Wood Studs 16”

Pilot Holes

Wall Pilot Holes

Wood Studs 24”

Pilot Holes

Hang the mount on

the wall temporarily

using a nail in the

center hole. Level the

mount before drilling

pilot holes.

Installation Instructions PLP Series

PLP INSTALLATION (Cont’d)

Mount the PLP

To mount the PLP, do the following:

1. Holding the PLP against the wall, select the pair of

mounting holes that best suits your situation (see

Figures 5, 6, and 7).

NOTE: The mounting holes are slotted to allow for a

small degree of lateral movement. The mount can

be centered, or shifted to the left of center, or

right of center depending on stud location.

NOTE: Lag bolts and washers are not supplied.

2. Depending on your situation, install the lag bolts and

washers into the pilot holes previously drilled, as

described below.

•Option A. Install four 5/16” x 2 ½” lag bolts and

four 5/16” washers (two top and two bottom) into

the mounting holes, centering the PLP on dual

wood studs 16” apart on center as shown in

Figure 5.

•Option B. Install four 5/16” x 2 ½” lag bolts and

four 5/16” washers (two top and two bottom) into

the mounting holes that are right of center on

dual wood studs 16” apart as shown in Figure 6.

•Option C. Install four 5/16” x 2 ½” lag bolts and

four 5/16” washers (two top and two bottom) into

the mounting holes that are left of center on dual

wood studs 16” apart dual wood studs 16” apart

on center as shown in Figure 6.

•Option D. Install four 5/16” x 2 ½” lag bolts and

four 5/16” washers (two top and two bottom) into

the mounting holes, centering the PLP on dual

wood studs 24” apart on center as shown in

Figure 7.

3. Tighten all lag bolts.

Figure 5. Mounting Holes – 16” Apart on Center

(Option A)

Figure 6. Mounting Holes – 16" Apart on Center

(Options B and C)

Figure 7. Mounting Holes – 24" Apart On Center

(Option D)

Option B

Option C

Option A

Option D

Installation Instructions PLP Series

ATTACH PSB TO THE DISPLAY

To attach the PSB to the display, do the following:

•To help your identify the correct PSB that matches

the model number of your display, refer to the cross-

reference chart at www.chiefmfg.com.

•To download the corresponding PSB installation

instructions, refer to www.chiefmfg.com.

•Contact Customer Service at 952-582-6480 if you

have any questions about how to select the PSB that

matches the model number of your display.

INSTALL THE DISPLAY

To install the display, do the following:

NOTE: Verify that all power/audio/video cables are

disconnected from the display and the latching

flag is lowered in the down position before

attempting to mount the display.

1. With the aid of another person, lift the display up to

the mount on the wall, aligning mounting buttons

with the teardrop slots on the mount, and lower the

display firmly into place (Figure 8).

2. Raise the latching flag to secure the display (see

Figure 9). If the flag does not fully engage, check to

ensure the mounting buttons are fully seated in the

slots.

NOTE: A padlock may be installed through the hole in

the latching flag for additional security.

REMOVE THE DISPLAY

To remove the display from the mount, do the following:

1. Disconnect all power/audio/video cables.

2. Lower the latching flag to unlock the display (refer to

Figure 9).

3. With the aid of another person, lift the display up and

out of the teardrop slots in the mount to remove the

display.

Figure 8. Install the Display

Figure 9. Raise Latching Flag to Lock

Lock

Unlock

Latching

Flag

Teardrop Slot

PLP

Dis

PSB

Installation Instructions PLP Series

TILT ADJUSTMENT

To tilt the display 0°to 15°down, do the following:

1. Manually tilt the display 0°to 15°down into the

desired position.

2. If desired, tighten the nut (see Figure 10) to increase

the amount of tension needed to hold the mount in

the position set in Step 1.

NOTE:Tighten the nuts only to adjust the amount of

tension needed to manually tilt and hold the

mount in place. Do not over-tighten the nuts.

Over-tightening the nuts may cause excessive

wear and may damage your mount.

3. Repeat Steps 1 and 2 until the desired tension is

obtained.

CABLE CONNECTION

To installed or removed cables, do the following:

1. Manually tilt the display 0°to 7°up into the service

position (see Figure 11).

2. Lower center support bar to keep the display tilted up

(see Figure 12).

3. Perform service. For example: Connect or disconnect

the power/audio/video cables.

NOTE:The service position is not recommended as a

final display position.

4. Raise the center support bar and reposition the

display to desired position (if necessary, refer to

“TILT ADJUSTMENT” procedure) after service is

completed.

WARNING: Watch for pinch points. Do not put your

fingers between movable parts.

Figure 10. Tilt Display Down

Figure 11. Tilt Display Up (for service only)

Figure 12. Cable Connection

Center

support bar

Tilt the display

0°to 7°to connect

or disconnect cables.

1.Tilt display up

2.Lower support bar.

3.Perform service.

4.Return display to

desired position.

1.Adjust pitch

2.If necessary, tighten

nut slightly to

increase tension.

Inhaltsverzeichnis

Andere CHIEF Rack & Stand Handbücher

CHIEF

CHIEF KRA225 Bedienungsanleitung

CHIEF

CHIEF TS318SU Bedienungsanleitung

CHIEF

CHIEF MAGNA-VIEW Bedienungsanleitung

CHIEF

CHIEF NS1F1223 Bedienungsanleitung

CHIEF

CHIEF CPA395 Bedienungsanleitung

CHIEF

CHIEF FMSCAO Bedienungsanleitung

CHIEF

CHIEF FTR1U Bedienungsanleitung

CHIEF

CHIEF SSB-313 Bedienungsanleitung

CHIEF

CHIEF PAC717 Bedienungsanleitung

CHIEF

CHIEF GPM-110 Bedienungsanleitung

CHIEF

CHIEF Fusion Service-Handbuch

CHIEF

CHIEF CM2C40 Bedienungsanleitung

CHIEF

CHIEF Fusion FCA831 Bedienungsanleitung

CHIEF

CHIEF FHB3047 Bedienungsanleitung

CHIEF

CHIEF PNRIW Series Bedienungsanleitung

CHIEF

CHIEF LFAU Bedienungsanleitung

CHIEF

CHIEF Kontour KRA234 Bedienungsanleitung

CHIEF

CHIEF CM-7 Bedienungsanleitung

CHIEF

CHIEF RMF Bedienungsanleitung

CHIEF

CHIEF JWDIW Bedienungsanleitung

CHIEF

CHIEF PST 2000 Series Bedienungsanleitung

CHIEF

CHIEF PAC-300 Bedienungsanleitung

CHIEF

CHIEF PACLR2 Bedienungsanleitung

CHIEF

CHIEF TPS Series Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung