Chord CPA3000 Bedienungsanleitung

CPA3000 Preamplifier

CONTENTS

PRODUCT DESCRIPTION 3

INVENTORY 3

WHEN SETTING UP 4

SAFETY WARNINGS 5

AC POWER CONNECTION 6

CONNECTING YOUR EQUIPMENT 7

INPUT CONNECTIONS 8

OUTPUT CONNECTIONS 9

RECORDING 10

AV BYPASS 11

EVERYDAY USE OF YOUR CPA3000 12

USING THE REMOTE CONTROL 14

MAINTENANCE 16

FREQUENTLY ASKED QUESTIONS 16

TRIGGER OUTPUTS 17

PRODUCT SPECIFICATION 18

CPA3000 Preamplifier

Thank you for buying a Chord Electronics product.

Before you start to enjoy your preamplifier, please take a couple of minutes to read how to connect your audio equipment

and how to maximise your listening experience.

Product Description

Using similar technology as the highly successful CPA5000 reference preamplifier the CPA3000 features a high

frequency switch mode power supply and ultra low noise circuitry to give the very best noise floor performance.

Four pairs of balanced style XLR inputs allows for great flexibility with two additional RCA inputs for unbalanced

sources. A single tape loop is available for playback and also to record from any of the connected sources.

Front panel controls allow for easy input and output selection if required but changes can also be made via the supplied

remote control. Cleverly situated under the main display, signal detection indicators have been replaced with highly

accurate VU meters. These give both clear signal detection and accurate input level. Naturally via the front panel control,

these may be selected or disabled as required. Two polished and nickel plated aluminium controls feature prominently to

manually adjust the volume and the balance and give easy visual reference of the settings. Using the precision motorised

Alps potentiometers levels can also be adjusted by remote control. All settings are clearly visible via the large easy to

read vacuum fluorescent display and are retained even when power is removed.

Inventory

As well as your CPA3000 and this user manual, you should also have received the following items.

1. System Remote Control including user manual

2. Power cord

3. Chord guarantee registration card

When setting up

To ensure that your CPA3000 works efficiently and safely, please pay particular attention to the following issues.

ventilation

Your CPA3000 should have at least 5cm of clear space all around it to ensure a free flow of air at all times. We do not

recommend that you place CPA3000 directly on a carpet. If you have the optional integra leg system fitted it is

recommended that the power amplifiers sit above the CPA3000.

AC lead and plug

All Chord equipment comes supplied with the correct power lead and plug. This should be used at all times.

if you need to fit a plug for UK/Europe

Connect the blue wire to the neutral terminal

Connect the brown wire to the live terminal

Connect the yellow/green wire to the earth terminal

if you need to fit a plug for US/Canada

Connect the white wire to the neutral terminal

Connect the black wire to the live terminal

Connect the green to the earth terminal

earthing issues in Europe

In some European countries a hum may occur if your CPA3000 is connected to mains sockets that do not have an earth. If

this is the case please ensure that:

1. Your transport is connected via a multi-way mains block, which contains an earth point

at each socket outlet. This is to ensure that the chassis metalwork of each item is

connected together.

2. We recommend that an earthing method for your building be implemented.

3. Use the connecting points on your Chord unit and connect to an available earth point.

Safety Warnings

It is important that your CPA3000 is earthed at all times via its own mains lead. Failure to do this may be hazardous. The

power supply components within the CPA3000 are designed to operate at lethal voltages and energy levels. Circuit

designs that embody these components conform to applicable safety requirements. Precautions must be taken to prevent

accidental contact with power-line potentials. Do not connect grounded test equipment.

There are no user serviceable parts within the CPA3000 Reference Preamplifier. Unauthorised

tampering or dismantling of this product will invalidate the warranty and could cause injury.

AC Power connection

The AC power connector of CPA3000 is at the back of the unit. Plug the female end (socket) of the power cord into the

power connector of the transport, and the male end(plug) of the power cord into AC wall socket or AC extension socket.

The CPA3000 features a universal voltage high frequency power supply and will operate automatically from 65V to

260V AC, 50 or 60Hz.

For optimum operation it is recommended that the CPA3000 is connected directly to the wall socket via the power

cord provided.

AC connector and switch

Powering up

Press the rear panel switch marked power. The display and internal illumination will light up. The display will show the

selected input.

Powering down

Press the rear panel switch marked power. The CPA3000 utilises soft start circuitry so the power can switched on and off

as often as required. There is no need to leave the CPA3000 permanently switched on.

Live

Neutral

Earth

Mains Switch

Connector

Connecting your equipment

Chord amplifiers are supplied with and designed to be connected using balanced inputs. The interconnecting cables you

use will depend on the available input and output sockets on your other equipment. We have installed unbalanced inputs

on all Chord equipment, thus enabling you to mix Chord Electronics and other manufacturer’s equipment.

Balanced inputs carry twice the strength of signal of unbalanced inputs and are able to be fed down long lengths of cable

with less deterioration of signal. They are also less prone to interference than unbalanced inputs. Balanced inputs have

three pins and use Neutric XLR style connectors. Pin 1 is earth, pin 2 is positive and pin 3 is negative.

Unbalanced inputs use RCA phono connectors, which are gold plated with teflon high performance dielectric insulators

for optimum performance.

Basic system diagram

outputs

inputs

CD Transport

Turntable

outputs

inputs

outputs

inputs

outputs

inputs

DAC 64

SYMPHONIC

phono stage

power amplifier

pre-amplifier

speakers

-Amplfication

-Switching and

level control

-Data and

analogue

conversion

-Signal

Source

Red Reference

CD Player

Input Connections

You can connect up to 7 items of source equipment. Included is a tape loop for recording purposes. All input connections

are on the rear panel and are marked with the corresponding Line number. Lines 1 to 4 are balanced inputs, Line 5, 6 and

TAPE are RCA phono style inputs. Left channel connections are at the top, right channel connections are at the bottom.

It does not matter which input you choose just select the same type of connection that your source has.

Note: Moving coil turntables without an internal amplifier will require an external phono stage amplifier such as the

Chord Symphonic before connecting to the CPA3000.

TAPE

Output Connections

You need to connect the outputs on the back of the CPA3000 to a power amplifier in order to drive your loudspeakers.

There is one pair of balanced XLR outputs or one pair of RCA phono outputs each of which will drive a 68 ohm load.

Choose either depending on the appropriate input connection on your power amplifier. Left channel connections are at

the top, right channel connections are at the bottom.

Note: For optimum performance it is recommended that the balanced outputs are used where possible.

If you wish to bi-amp then ask your interconnect manufacturer to provide you with a balanced or RCA cable splitter. This

will split the single output from the CPA3000 into two signals one for each amplifier.

O/P

Recording

You can record an input from any of the connected audio sources to the tape output. If you’ve been using a tape recorder

as an input source, it will already be connected to the TAPE IN socket. Connect the tape recorder input to the TAPE OUT

RCA connection to record the selected audio source.

connecting to a Tape recorder to tape an audio source

Use RCA connectors to the left and right pairs marked OUT TAPE.

Note: In these examples we have used a tape recorder but you can use any recording device with a phono input. Minidisc,

CD/DVD recorders and PC soundcards are all normally compatible.

TAPE

OUT

Inhaltsverzeichnis

Andere Chord Verstärker Handbücher

Chord

Chord TToby Bedienungsanleitung

Chord

Chord CA30 Bedienungsanleitung

Chord

Chord ULTIMA 2 Bedienungsanleitung

Chord

Chord ULTIMA PRE Bedienungsanleitung

Chord

Chord Mojo2 Bedienungsanleitung

Chord

Chord ULTIMA PRE Bedienungsanleitung

Chord

Chord CB-25 Bedienungsanleitung

Chord

Chord ULTIMA 3 Gebrauchsanweisung

Chord

Chord ULTIMA PRE 2 Bedienungsanleitung

Chord

Chord CVH-40 Bedienungsanleitung

Chord

Chord PRIMA Gebrauchsanweisung

Chord

Chord SPM 600 Bedienungsanleitung

Chord

Chord SPM 6000 Mk2 Bedienungsanleitung

Chord

Chord HugoTT Bedienungsanleitung

Chord

Chord SPM 650 Bedienungsanleitung

Chord

Chord Etude Bedienungsanleitung

Chord

Chord CPA 2500 Bedienungsanleitung

Chord

Chord SPM 1200 MK2 Bedienungsanleitung

Chord

Chord CPA 3200E Bedienungsanleitung

Chord

Chord SYMPHONIC Bedienungsanleitung

Chord

Chord Hugo Bedienungsanleitung

Chord

Chord DAVE Bedienungsanleitung

Chord

Chord 173.442 Bedienungsanleitung

Chord

Chord SPM 1050 Bedienungsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung