Christie LX501 Bedienungsanleitung

LX501/LW401/LWU421/

LX601i/LW551i/LWU501i

Setup Guide

020-000504-02

http://www.pureglare.com.au

ENGLISH

Setup Guide 020-000504-02 Rev. 1 (06-2012)

LX501/LX601i/LW401/LW551i/LWU421/LWU501i

Projector

LX501/LW401/LWU421/

LX601i/LW551i/LWU501i

Setup Guide User's Manual (concise)

Thank you for purchasing this projector.

Please read through this manual before using this product, in order to use safely

and utilize well the product.

WARNING ►Before using this product, be sure to read all manuals for this

product. After reading them, store them in a safe place for future reference.

►Heed all the warnings and cautions in the manuals or on the product.

►Follow all the instructions in the manuals or on the product.



First of all............................................ 2

Entries and graphical symbols explanation ......2

Important safety instruction ..............................2

Regulatory notices.............................. 3

About Electro-Magnetic Interference ................3

About Waste Electrical and Electronic Equipment

...4

Contents of package........................... 4

Preparing for the remote control......... 5

Arrangement....................................... 6

Connecting with your devices............. 7

Fastening the adapter cover............... 8

Fastening the cable holder ................. 8



Connecting power supply ................... 9

Turning on the power........................ 10

Adjusting the projector's elevator ..... 11

Adjusting the lens position................ 11

Displaying the picture ....................... 12

Turning off the power........................ 13

Replacing the lamp........................... 14

Cleaning and replacing the air ﬁlter

.. 16

Using the CD manual ....................... 18

Speciﬁcations ................................... 19

Troubleshooting

- Warranty and after-service ........... 21

Contents

NOTE • In this manual, unless any comments are accompanied, “the

manuals” means all the documents provided with this product, and “the product”

means this projector and all the accessories came with the projector.

http://www.pureglare.com.au

Setup Guide 020-000504-02 Rev. 1 (06-2012)

LX501/LX601i/LW401/LW551i/LWU421/LWU501i

First of all

Entries and graphical symbols explanation

The following entries and graphical symbols are used for the manuals and the product

as follows, for safety purpose. Please know their meanings beforehand, and heed them.

Important safety instruction

The followings are important instructions for safely using the product. Be sure to

follow them always when handling the product. The manufacturer assumes no

responsibility for any damage caused by mishandling that is beyond normal usage

deﬁned in these manuals of this projector.

WARNING

This entry warns of a risk of serious personal injury or even death.

CAUTION This entry warns of a risk of personal injury or physical damage.

NOTICE This entry notices of fear of causing trouble.

WARNING ►Never use the product in or after an abnormality (ex. giving

off smoke, smelling strange, took a liquid or an object inside, broken, etc.) If an

abnormality should occur, unplug the projector urgently.

►Situate the product away from children and pets.

►Keep small parts away from children and pets. If swallowed, consult a

physician immediately for emergency treatment.

►Do not use the product when there is fear of a thunderbolt.

►Unplug the projector from the power outlet if the projector is not used for the

time being.

►

Do not connect the projector to a power supply while no lens unit is attached to it.

►Do not open or remove any portion of the product, unless the manuals direct

it. For internal maintenance, leave it to your dealer or their service personnel.

►Use only the accessories speciﬁed or recommended by the manufacturer.

►Do not modify the projector or accessories.

►Do not let any things or any liquids enter to the inside of the product.

►Do not wet the product.

►

Do not place the projector where any oils, such as cooking or machine oil, are used.

Oil may harm the product, resulting in malfunction, or falling from the mounted position.

►Do not apply a shock or pressure to this product.

- Do not place the product on an unstable place such as the uneven surface or

the leaned table.

- Do not place the product unstably. Place the projector so that it does not

protrude from the surface where the projector is placed on.

- Place your hands on the grip on the bottom of the projector when carrying the

projector.

- Remove all the attachments including the power cord and cables, from the

projector when carrying the projector.

►

Do not look into the lens and the openings on the projector, while the lamp is on.

►

Do not approach the lamp cover and the exhaust vents, while the projection lamp

is on. Also after the lamp goes out, do not approach them for a while, since too hot.

http://www.pureglare.com.au

ENGLISH

Setup Guide 020-000504-02 Rev. 1 (06-2012)

LX501/LX601i/LW401/LW551i/LWU421/LWU501i

Regulatory notices

About Electro-Magnetic Interference

This is a Class A product. In a domestic environment this product may cause

radio interference in which case the user may be required to take adequate

measures.

This product may cause interference if used in residential areas. Such use must

be avoided unless the user takes special measures to reduce electromagnetic

emissions to prevent interference to the reception of radio and television

broadcasts.

In Canada

This Class A digital apparatus complies with Canadian ICES-003.

In the US and places where the FCC regulations are applicable

This device complies with part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.This equipment has

been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential

area is likely to case harmful interference in which case the user will be required to

correct the interference at his own expense.

INSTRUCTIONS TO USERS: Some cables have to be used with the core set.

Use the accessory cable or a designated type cable for the connection. For cables

that have a core only at one end, connect the core to the projector.

CAUTION: Changes or modiﬁcations not expressly approved by the party

responsible for compliance could void the user’s authority to operate the

equipment.

http://www.pureglare.com.au

Setup Guide 020-000504-02 Rev. 1 (06-2012)

LX501/LX601i/LW401/LW551i/LWU421/LWU501i

Contents of package

Your projector should come with the items

shown below. Check that all the items are

included. Require of your dealer immediately if

any items are missing.

(1) Remote control with two AA batteries

(2) Power cord

(3) Computer cable

(4) HDMITM-DVI cable

(5) Lens cover

(6) User’s manuals (Book x1, CD x1)

(7) Security label

(8) Application CD

(9) Adapter cover

(10) Cable holder

NOTE • Keep the original packing materials for future reshipment. Be sure

to use the original packing materials when moving the projector. Use special

caution for the lens.

• The projector may make a rattling sound when tilted, moved or shaken, since

a ﬂap to control the air ﬂow inside of the projector has moved. Be aware that

this is not a failure or malfunction.

About Waste Electrical and Electronic Equipment

The mark is in compliance with the Waste Electrical and Electronic

Equipment Directive 2002/96/EC (WEEE).

The mark indicates the requirement NOT to dispose the equipment

including any spent or discarded batteries or accumulators as unsorted

municipal waste, but use the return and collection systems available.

If the batteries or accumulators included with this equipment, display

the chemical symbol Hg, Cd, or Pb, then it means that the battery has a

heavy metal content of more than 0.0005% Mercury or more than, 0.002%

Cadmium, or more than 0.004% Lead.

Regulatory notices (continued)

WARNING ►Keep small parts away from children and pets. Take care

not to put in the mouth. If swallowed, consult a physician immediately for

emergency treatment.

NOTICE ►It is recommended that the adapter cover or the cable holder

is used with the USB wireless adapter (optional) to prevent the adapter from

becoming detached and to avoid the risk of burns.

(6)

(7)

(2)

(3)

(5)

(8)

(1)

(9)

(10)

(4)

http://www.pureglare.com.au

ENGLISH

Setup Guide 020-000504-02 Rev. 1 (06-2012)

LX501/LX601i/LW401/LW551i/LWU421/LWU501i

Preparating for remote control

Please insert the batteries into the remote control before using it. If the remote

control starts to malfunction, try to replace the batteries. If you will not use the

remote control for long period, remove the batteries from the remote control and

store them in a safe place.

1. Holding the hook part of the battery cover, remove it.

2. Align and insert the two AA batteries

(HITACHI MAXELL or HITACHI MAXELL

ENERGY, Part No.LR6 or R6P) according to

their plus and minus terminals as indicated in

the remote control.

3. Replace the battery cover in the direction of the arrow

and snap it back into place.

WARNING ►Always handle the batteries with care and use them only as

directed. Improper use may result in battery explosion, cracking or leakage,

which could result in ﬁre, injury and/or pollution of the surrounding environment.

• When replacing the batteries, replace both of the batteries with new batteries

of the same type. Do not use a new battery with a used battery.

• Be sure to use only the batteries speciﬁed. Do not use batteries of different

types at the same time. Do not mix a new battery with used one.

• Make sure the plus and minus terminals are correctly aligned when loading a

battery.

• Keep a battery away from children and pets.

• Do not recharge, short circuit, solder or disassemble a battery.

• Do not place a battery in a ﬁre or water. Keep batteries in a dark, cool and dry

place.

• If you observe battery leakage, wipe out the leakage and then replace a

battery. If the leakage adheres to your body or clothes, rinse well with water

immediately.

• Obey the local laws on disposing the battery.

http://www.pureglare.com.au

Setup Guide 020-000504-02 Rev. 1 (06-2012)

LX501/LX601i/LW401/LW551i/LWU421/LWU501i

WARNING ►Install the projector where you can access the power outlet

easily.

►Install the projector in a stable horizontal position.

• Do not use any mounting accessories except the accessories speciﬁed by the

manufacturer. Read and keep the manuals of the accessories used.

• For special installation such as ceiling mounting, be sure to consult your

dealer beforehand. Speciﬁc mounting accessories and services may be

required.

• Do not put the projector on its side, front or rear position.

• Do not attach nor place anything on the projector unless otherwise speciﬁed

in the manual.

►Do not install the projector near thermally conductive or ﬂammable things.

►Do not place the projector where any oils, such as cooking or machine oil, are

used.

►Do not place the projector in a place where it may get wet.

CAUTION ►Place the projector in a cool place with sufﬁcient ventilation.

• Keep a space of 30 cm or more between a side of the projector and other

objects such as walls.

• Do not stop up, block nor cover the projector's vent holes.

• Do not place the projector at places that are exposed to magnetic ﬁelds, doing

so can cause the cooling fans inside the projector to malfunction.

►Avoid placing the projector in smoky, humid or dusty place.

• Do not place the projector near humidiﬁers.

NOTICE ►Position the projector to prevent light from directly hitting the

projector’s remote sensor.

►Do not place the product in a place where radio interference may be caused.

►Set the ALTITUDE of the SERVICE item in the OPTION menu correctly. It is

recommended to leave it at AUTO usually. If the projector is used with a wrong

setting, it may cause damage to the projector itself or the parts inside. For de-

tails, see User Manual - Operating Guide.

Arrangement

Refer to tables T-1 to T-5 at the back of this manual as well as the following to

determine the screen size and projection distance. The values shown in the table

are calculated for a full size screen.

Projector top

Projector bottom

ⒽxⓋ : Screen size

ⓐ:

Projection distance

ⓑ,ⓒ: Screen height

Elevator feet

http://www.pureglare.com.au

ENGLISH

Setup Guide 020-000504-02 Rev. 1 (06-2012)

LX501/LX601i/LW401/LW551i/LWU421/LWU501i

Connecting with your devices

Before connecting the projector to a device, consult the manual of the device to

conﬁrm that the device is suitable for connecting with this projector and prepare

the required accessories, such as a cable in accord with the signal of the device.

Consult your dealer when the required accessory did not come with the product or

the accessory is damaged.

After making sure that the projector and the devices are turned off, perform the

connection, according to the following instructions. Refer to ﬁgures F-1 to F-4 at

the back of this manual.

For details, see User Manual - Operating Guide. Before connecting the projector

to a network system, be sure to read User Manual - Network Guide too.

WARNING ►Use only the appropriate accessories. Otherwise it could

cause a ﬁre or damage the projector and devices.

• Use only the accessories speciﬁed or recommended by the projector’s

manufacturer. It may be regulated under some standard.

• Neither disassemble nor modify the projector and the accessories.

• Do not use the damaged accessory. Be careful not to damage the accesso-

ries. Route a cable so that it is neither stepped on nor pinched out.

CAUTION ►For a cable with a core at only one end, connect the end with

the core to the projector. That may be required by EMI regulations.

►Before connecting the projector to a network system be sure to obtain the

consent of the administrator of the network.

►Do not connect the LAN port to any network that might have the excessive

voltage.

►The designated USB wireless adapter that is sold as an option is required to

use the wireless network function of this projector.

►Before removing the USB storage device from the port of the projector, be

sure to use the REMOVE USB function on the thumbnail screen to secure your

data. Before you insert or pull out the USB wireless adapter from the projector,

turn off the power of the projector and pull out the power cord’s plug from the

outlet. Do not touch the USB wireless adapter while the projector is receiving

AC power.

NOTE • Do not turn on or off the projector while connected to a device in

operation, unless that is directed in the manual of the device.

• Some input ports are selectable in the use. For details, see User Manual -

Operating Guide.

• Be careful not to mistakenly connect a connector to a wrong port.

•

If an oversized USB storage device blocks the LAN port, use a USB extension

cable to connect the USB storage device.

http://www.pureglare.com.au

Setup Guide 020-000504-02 Rev. 1 (06-2012)

LX501/LX601i/LW401/LW551i/LWU421/LWU501i

Fastening the cable holder

Use the supplied cable holder to prevent

the USB wireless adapter and the HDMITM

cables from becoming detached.

When using the cable holder, connect the

USB wireless adapter to the further USB

TYPE A port from the LAN port.

1. Remove the screw marked with a

triangle and the screw marked with a

diamond.

2. Open the cable holder clip and then

align the screw holes on the projector

and the holder. Then insert the screw

removed from the projector into the hole

and tighten the screw.

3. Snap the clip closed to secure the

HDMITM cables in place.

Fastening the adapter cover

Use the supplied adapter cover to prevent

the USB wireless adapter from coming

off easily. When using the adapter cover,

connect the USB wireless adapter to the

further USB TYPE A port from the LAN

port.

1. Loosen the screw marked with a

triangle.

2. Insert the tab of the cover into the hole

at the upper right of the USB TYPE A ports in the

direction of the arrow.

3. Align the screw holes on the projector and the cover.

Then insert the screw removed from the projector into the hole and tighten

the screw.

WARNING ►Keep small parts away from children and pets. Take care not

to put in the mouth.

2, 3

WARNING ►Keep small parts away from children and pets. Take care not

to put in the mouth.

Tab

Cable holder

http://www.pureglare.com.au

ENGLISH

Setup Guide 020-000504-02 Rev. 1 (06-2012)

LX501/LX601i/LW401/LW551i/LWU421/LWU501i

Connecting power supply

1. Put the connector of the power cord into the

AC IN (AC inlet) of the projector.

2. Firmly plug the power cord’s plug into the

outlet. In a couple of seconds after the power

supply connection, the POWER indicator will

light up in steady orange.

Please remember that when the DIRECT POWER

ON function activated, the connection of the power

supply make the projector turn on.

WARNING ►Do not connect the projector to a power supply while no lens

unit is attached to it.

►Please use extra caution when connecting the power cord, as incorrect or

faulty connections may result in ﬁre and/or electrical shock.

• Do not touch the power cord with a wet hand.

• Only use the power cord that came with the projector. If it is damaged, consult

your dealer to get a new one. Never modify the power cord.

• Only plug the power cord into an outlet whose voltage is matched to the power

cord. The power outlet should be close to the projector and easily accessible.

Remove the power cord for complete separation.

• Do not distribute the power supply to multiple devices. Doing so may overload

the outlet and connectors, loosen the connection, or result in ﬁre, electric

shock or other accidents.

• Connect the ground terminal for the AC inlet of this unit to the ground terminal

of the building using an appropriate power cord (bundled).

NOTICE ►This product is also designed for IT power systems with a phase-

to-phase voltage of 220 to 240 V.

AC IN

Power

cord

http://www.pureglare.com.au

Andere Handbücher für LX501

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Christie Projektor Handbücher

Christie

Christie Solaria CP2210 Bedienungsanleitung

Christie

Christie Mirage SST Montageanleitung

Christie

Christie DS+5K Bedienungsanleitung

Christie

Christie Crimson Series Bedienungsanleitung

Christie

Christie J Series Bedienungsanleitung

Christie

Christie CineLife+ CP4415-RGB Bedienungsanleitung

Christie

Christie Cinema 4K-RGB CP4315-RGB Bedienungsanleitung

Christie

Christie LW401 Bedienungsanleitung

Christie

Christie Vista S3 Bedienungsanleitung

Christie

Christie Griffyn Series Montageanleitung

Christie

Christie Boxer 30 Gebrauchs- und Pflegehandbuch

Christie

Christie CineLife+ RGB PLF Montageanleitung

Christie

Christie L2K1500 Bedienungsanleitung

Christie

Christie DHD630-GS Bedienungsanleitung

Christie

Christie Crimson Gebrauchs- und Pflegehandbuch

Christie

Christie Roadie HD+30K Bedienungsanleitung

Christie

Christie DS+405 Bedienungsanleitung

Christie

Christie LHD700 Bedienungsanleitung

Christie

Christie LX1750 Bedienungsanleitung

Christie

Christie Christie LX120 Bedienungsanleitung

Christie

Christie DS+26 Bedienungsanleitung

Christie

Christie DHD800 Bedienungsanleitung

Christie

Christie CP2415-Xe Montageanleitung

Christie

Christie D4K3560 Bedienungsanleitung

Beliebte Projektor Handbücher anderer Marken

iEmmet

iEmmet MP-312 Bedienungsanleitung

Epson

Epson VS400 Bedienungsanleitung

Sony

Sony VPL-HS10 Marketing Specifications & Features Bedienungsanleitung

Sony

Sony VPL-HW65ES Service-Handbuch

Toshiba

Toshiba TLP-791U Bedienungsanleitung

Philips

Philips LC1341 Referenzhandbuch

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung

NEC

NEC NP600S EDU Bedienungsanleitung

BenQ

BenQ SH753P Bedienungsanleitung

Eiki

Eiki EK-623U series Bedienungsanleitung

Epson

Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung

Epson

Epson PowerLite Home Cinema 705HD Bedienungsanleitung

Navitar

Navitar FX Bedienungsanleitung

InFocus

InFocus LitePro 560 Bedienungsanleitung

Sony

Sony SRX-R815P Bedienungsanleitung

Vivitar

Vivitar DP1500 X Bedienungsanleitung

Acer

Acer C20 Series Bedienungsanleitung

Asus

Asus ZenBeam Latte Bedienungsanleitung