Christie ML10 Bedienungsanleitung

Installing 46-55" ﬂat

panel screens on the

ML10/MP10 wall mount

The ML10/MP10 is a full-service video wall mount that can accommodate the FHD462-X and FHD552-X

LCD flat panels.

The ML10 mount is used for landscape orientations and the MP10 mount is used for portrait

orientations. The modular mount system features an innovative pull-out and prop-open hinge

mechanism that provides rear screen access, the ability to adjust the X, Y, and Z axis alignment, and

wall plate spacers that set each mount into position.

Features

Use the ML10 and MP10 wall mounts to hang and adjust the flat panels, and to access the rear of the

panels.

• Modular mount for large video wall display configurations.

• Tool-less adjustments of panels for optimal gaps.

• Spring-loaded mechanisms secure displays.

Installing Flat Panels on the ML10/MP10 Wall Mount Instruction Sheet 1

020-101712-03 Rev. 1 (07-2015)

• Pull-out/prop-open mechanism provides quick service access.

•Integrated cable management tie-backs make display-to-display cabling simple.

• Included security hardware prevents the mount from extending out from the wall.

• Adjustable VESA® mounting hole patterns in 100 mm (3.9”) increments, starting at 200 x 200

mm (7.9” x 7.9”) up to 700 x 400 mm (27.5” x 15.7”) for ML10 LCD mounts. Additional

patterns supported with adapter plates.

• Adjustable VESA® mounting hole patterns in 100 mm (3.9”) increments, starting at 200 x 200

mm (7.9” x 7.9”) up to 600 x 400 mm (23.6” x 15.7”) for MP10 LCD mounts. Additional

patterns supported with adapter plates.

Safety warnings and cautions

To prevent personal injury and to protect the device from damage, read and follow these safety

precautions.

Warning! Failure to comply with the following could result in death or serious injury.

• The supporting structure must safely support the combined load of the product, all attached

hardware, and components following all local safety standards and regulations.

• A minimum of two people or lift equipment is required to safely lift, install, or move the product.

• Always handle the screen from its sides. Do not touch the inside of the screen.

• Christie products must be installed and serviced by Christie qualified technicians.

Caution! Failure to comply with the following could result in minor or moderate injury.

• Do not over-tighten hardware.

• This product is intended for indoor use only.

Types of installations

Learn the supported surfaces for installing the wall mounts.

Wall construction Hardware required

Wood Stud Included

Wood Beam Included

Solid Concrete Not Included

Cinder Block Not Included

Unistrut P series Not Included

Metal Stud Contact Qualified Professional

Brick Contact Qualified Professional

Other Contact Qualified Professional

Installing 46-55" flat panel screens on the ML10/MP10 wall mount

Installing Flat Panels on the ML10/MP10 Wall Mount Instruction Sheet 2

020-101712-03 Rev. 1 (07-2015)

Required kits

Learn the kits that are required for installing the wall mounts.

• LCD Mount 40-65” ML10 (Landscape) P/N: 135-101103-xx

• LCD Mount 40-65” MP10 (Portrait) P/N: 135-104106-xx

Optional kits

• LCD Spacer Kit 55” ML10 (135-102104-xx)

• LCD Spacer Kit 55” MP10 (135-107109-xx)

Other available resources

•LCD Panel FHD552-X User Manual (P/N: 020-000741-xx)

•LCD Panel FHD462-X User Manual (P/N: 020-000769-xx)

•ML10/MP10 Spacer Kit for the FHD552-X Instruction Sheet (P/N: 020-100728-xx)

Required parts

Learn the parts necessary for installing the wall mounts.

A Pull out mount assembly (Qty. 1) H M6 x 12 mm socket pin screw (Qty. 4)

Installing 46-55" flat panel screens on the ML10/MP10 wall mount

Installing Flat Panels on the ML10/MP10 Wall Mount Instruction Sheet 3

020-101712-03 Rev. 1 (07-2015)

B Adapter Bracket (Qty. 2) I M8 x 16 mm socket pin screw (Qty. 4)

C #14 x 2.5” hex head wood screw (Qty. 5) J 4mm Allen wrench (Qty. 1)

E Fender washer (Qty. 4) - Mesh sleeve (not shown) (Qty. 1)

F Nylon shoulder washer (Qty. 4) - Cable tie (not shown) (Qty. 2)

G M5 x 10 mm socket pin type-F screw (Qty. 2)

Required tools

Ensure the appropriate tools are available during the installation.

• Stud finder (edge-to-edge stud finder is recommended)

• Phillips® screwdriver

• Socket wrench

• Pencil

• Drill

• 3/8" socket

• 5/16” (8 mm) bit for concrete and cinder block walls

• 5/32” (4 mm) bit for wood stud walls

• Level

Installing the wall mount

Learn how to install the wall mounts onto different surfaces.

The maximum load capacity of the wall mount is 125 lbs (57 kg). Illustrations are graphical

representations only and are provided to enhance the understanding of the written material.

When installing the wall mounts, ensure there is proper spacing between the mounts to accommodate

the panels. Always start with the bottom left display in the array.

1. Measure the width and height of the display panel.

2. Locate the center of the bottom left display.

Installing 46-55" flat panel screens on the ML10/MP10 wall mount

Installing Flat Panels on the ML10/MP10 Wall Mount Instruction Sheet 4

020-101712-03 Rev. 1 (07-2015)

3. To identify where the mount for the display to the right of the first display should be installed,

measure the width of the display panel from the center of the first display to the center of the

second display (X).

4. Install all panels in the bottom row.

Install all rows starting with the far left display.

Installing 46-55" flat panel screens on the ML10/MP10 wall mount

Installing Flat Panels on the ML10/MP10 Wall Mount Instruction Sheet 5

020-101712-03 Rev. 1 (07-2015)

5. To identify where the mount for the second row of displays should be installed, measure the

height of the display panel from the top of the bottom left display to the top of the first

display in the second row (Y).

Installing the mount to wall studs, plywood, drywall over wall

studs

Learn how to install the wall mounts onto wall studs, plywood, or drywall.

Hardware provided is for attaching the mount through standard thickness drywall or plaster into wood

studs. Installers are responsible for providing the hardware for other types of mounting situations.

When installing the wall mounts on a wood stud wall covered with plywood, verify that the wood studs

are a minimum of 2" x 4" nominal size and plywood is a minimum 1/2" (13 mm) thickness. Plywood

may be covered by drywall up to 5/8" thick.

1. Use an “edge-to-edge” stud finder to locate the edges of the stud.

2. Based on their edges, draw a vertical line down the stud center.

3. Place the pull out mount assembly on the wall to use as a template, and verify the pull out

mount is level on the center line of the stud.

4. Mark the center of the four mounting holes.

Installing 46-55" flat panel screens on the ML10/MP10 wall mount

Installing Flat Panels on the ML10/MP10 Wall Mount Instruction Sheet 6

020-101712-03 Rev. 1 (07-2015)

In the landscape orientation, make sure there is a minimum 16” (406.4 mm) horizontal

distance between the #14 x 2.5” screws.

Landscape orientation Portrait orientation

5. Drill four 5/32" (4 mm) diameter holes 2-1/2" (65 mm) deep.

6. Tighten the four #14 x 2.5" wood screws and fender washers so that the wall plate is firmly

attached, but do not over-tighten.

Never tighten in excess of 80 in-lbs (9Nm).

Installing the mount to solid concrete or cinder block

Learn how to install the wall mounts onto solid concrete or cinder block walls.

Warning! Failure to comply with the following could result in death or serious injury.

• Concrete must be a minimum of 2000 psi density. Lighter density concrete may not hold the

concrete anchor.

• The supporting structure must safely support the combined load of the product, all attached

hardware, and components following all local safety standards and regulations.

When installing wall mounts onto cinder blocks, verify that you have a minimum of 1-3/8" (35 mm) of

actual concrete thickness in the hole to be used for the concrete anchors. Cinder block must meet

ASTM C-90 specifications and a minimum nominal width of 8".

1. Place the pull out mount assembly on the wall to use as a template, and verify the pull out

mount is level.

2. Mark the center of the four mounting holes.

In the landscape orientation, make sure there is a minimum 16” (406.4 mm) horizontal

distance between the #14 x2.5” screws.

Landscape orientation Portrait orientation

Installing 46-55" flat panel screens on the ML10/MP10 wall mount

Installing Flat Panels on the ML10/MP10 Wall Mount Instruction Sheet 7

020-101712-03 Rev. 1 (07-2015)

3. Use a standard electric drill on slow setting to drill four 5/16” (8 mm) diameter holes to a

minimum depth of 2.5” (64 mm).

To avoid breaking out the back of the hole when entering a void or cavity, do not use a

hammer drill. On cinder block walls, mount in a solid part of the block, generally 1" (25 mm)

minimum from the side of the block. Do not drill into mortar joints.

4. Insert anchors into the holes flush with the wall.

Never attach concrete expansion anchors to concrete covered with plaster, drywall, or other

finishing material. If mounting to concrete surfaces covered with a finishing surface is

unavoidable, the finishing surface must be counter bored, as shown in the image below.

5. Place the pull out mount assembly over the anchors and secure it with four #14 x 2.5”

screws, and fender washers.

Make sure concrete anchors do not pull away from the concrete when tightening screws. If

the wall is covered with plaster, drywall, or other finishing material thicker than 5/8" (16

mm), custom fasteners must be supplied by the installer.

6. Tighten the four #14 x 2.5" wood screws and fender washers so that the wall plate is firmly

attached, but do not over-tighten.

Never tighten in excess of 80 in-lbs (9Nm).

Installing the mount to a Unistrut P series metal frame

Learn how to install a wall mount onto the Unistrut metal frame channel.

When installing Peerless wall mounts to Unistrut "P" Series metal framing channels, the channels must

be installed and supported per the Unistrut design specifications. Use only compatible Unistrut

hardware. Never exceed maximum load capacity of Unistrut channel or supporting surface.

1. Insert the 1/4-20 Unistrut channel nut with spring on the Unistrut metal frame channel.

2. Level and install the Unistrut P series metal frame channel to the wall according to the

instructions included with the Unistrut frame.

3. Attach the wall mount to the Unistrut metal frame channel with the 1/4-20 hex head screws.

Installing 46-55" flat panel screens on the ML10/MP10 wall mount

Installing Flat Panels on the ML10/MP10 Wall Mount Instruction Sheet 8

020-101712-03 Rev. 1 (07-2015)

Installing the mount to the F100 frame

Learn how to install the wall mounts onto the F100 frame.

1. Make sure all components within the video wall are level, starting with the P100 Pedestal. If

the floor surface is not level adjust the feet on the pedestal.

For information on installing the P100 pedestal and the F100 frame, see P100 Pedestal and

F100 Frame for FHD552-X Installation Manual (020-101714-xx).

2. Install the F100 Frame onto the pedestal.

If the F100 Frame is used as stand alone unit it must be leveled before securing the wall

mount.

3. Before installing the wall mount use a standard level to check alignment on the horizontal and

vertical edge of the frame.

4. Position the wall mount within the center of the frame, aligning it with the mounting holes.

5. Tighten the wall mount to the F100 Frame using the four M6 screws.

Never tighten in excess of 80 in- lbs (9Nm).

Installing 46-55" flat panel screens on the ML10/MP10 wall mount

Installing Flat Panels on the ML10/MP10 Wall Mount Instruction Sheet 9

020-101712-03 Rev. 1 (07-2015)

6. For good screen planarity within a video wall adjust the top knob of the adapter bracket to

achieve a 9 mm (0.35”) gap.

7. Adjust the bottom knob of the adapter bracket to achieve a 14 mm (0.55”) gap. If further

adjustment is required, leave a 1 mm (0.04”) minimum clearance to allow the bracket to be

easily released.

Installing 46-55" flat panel screens on the ML10/MP10 wall mount

Installing Flat Panels on the ML10/MP10 Wall Mount Instruction Sheet 10

020-101712-03 Rev. 1 (07-2015)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Christie Rack & Stand Handbücher

Christie

Christie MPL15 Bedienungsanleitung

Christie

Christie ML20 Bedienungsanleitung

Christie

Christie CP2220 Montageanleitung

Christie

Christie ML25 Bedienungsanleitung

Christie

Christie P100 Bedienungsanleitung

Christie

Christie 38-817001-01 Series Bedienungsanleitung

Christie

Christie Christie One Mount Bedienungsanleitung

Christie

Christie MPL15 Bedienungsanleitung

Christie

Christie MPL15 Bedienungsanleitung

Christie

Christie 38-804785-01 Bedienungsanleitung

Christie

Christie Power Rack Betriebsanleitung

Christie

Christie Remote Power Supply RackShelf Montageanleitung

Christie

Christie Christie One Mount Bedienungsanleitung

Christie

Christie Vive Audio BKT-LA5 Bedienungsanleitung

Christie

Christie RPMA series Bedienungsanleitung

Christie

Christie Entero Bedienungsanleitung

Christie

Christie Mirage SST Bedienungsanleitung

Christie

Christie Vivid LX20 Bedienungsanleitung

Christie

Christie 38-817001-01 Series Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung