Chroma Space Force 650-9070 Bedienungsanleitung

Space ForceTM octo LumenRadio Card QSG V2.0 QSG P/N: 650-0902

Quick Start Guide

Chroma-Q®

Space Force™octo

LumenRadio Card

For a full product manual please visit www.chroma-q.com

Part Number: CHFPFLR

Model: 650-9070

For use with

Part Number: CHSPF[XXXX], CQ647-XXXX, CQ1512-XXXX

Model: 650-XXXX, 647-XXXX, 1512-XXXX

Space ForceTM octo LumenRadio Card QSG V2.0 QSG P/N: 650-0902

1. Overview

The Chroma-Q®Space Force™ octo LumneRadio Card Kit allows addition of RF connectivity to

the Space Force™ octo light fixture. For a complete list of accessories please visit www.chroma-

q.com.

2. Kit Contents

Items

Part Number

Quantity

Radio Printed Circuit Board

650-0325

Round Spacer 5/16”

900-1321

Screw M3X20 Machine Screw

430-1220-0

Grommet for Antenna

430-1220-0

3. Tools Required

Torx T8 x 70mm Screwdriver (maximum torque: 0.62 N-m/ 5.5 in

‐

lb)

#1 Phillips Screwdriver or bit (Torque 5.5 in-lb)

4. Procedure

1. Place Space Force™unit acrylic side down on a surface

that will not scratch the lens, or damage the unit.

2. Carefully remove the 4 Torx screws that secure the ABS

plastic back cover. These screws have a T8 Torx head. If

using a power driver, set torque to 5.5 in-lb. Set aside the

screws.

3. Carefully lift the back cover from the unit. The adjusting

knobs will slide off with the cover. Remove the 5-pin

overlay connector from the PCB board before completely

removing the cover. Do not bend the pins. Set back cover

aside.

4. Remove the 4 x M3 screws from the PCB bracket

assembly using a Philip’s #1 screwdriver. If using a power

driver, set torque to 5.5lb-in. Set screws aside. On the

grounding side, there is a star washer- be sure this does

not fall into the unit. Set aside the hardware.

5. Unplug the engine connectors (white and

orange wires) from the PCB bracket

assembly to turn the assembly over and

expose the internal components. The order

of these connectors is not critical when

replacing them later.

Space ForceTM octo LumenRadio Card QSG V2.0 QSG P/N: 650-0902

6. Remove the jumper from the PCB

addressing card inside of the assembly. This

will not be required after you install the

wireless card.

7. Remove the 2 x M3 screws from the PCB addressing card. These will not be required after

you install the wireless card.

8. Included in the kit are two #4 Nylon 5/16” spacers. They

must be positioned as shown in the photograph.

9. Install the wireless card on top of these spacers and

into the jumper port as shown in the diagram. Use a #1

Phillips screwdriver to install the 2 - M3x20 screws

included in the kit to secure the wireless card. If using a

power driver, set torque to 5.5lb-in.

10. Insert the grommet attached to the antenna into the

holes on the engine. Ensure that the antenna does not

come out of grommet.

11. Reassemble the unit in the reverse order. Please remember

- Do not over-torque the screws. If possible, use the recommended torques in this guide.

- Reassemble the ground to the PCB bracket assembly using the M3 star washer.

- When re-assembling the back cover, be sure to carefully plug the overlay 5 pin connector

back into the addressing card. Ensure all 5 pins are connected and carefully adjust the

harness so it does not interfere with the display or closing of the unit.

- Be sure the placement of the back cover is even before replacing the screws. Check all

corners before proceeding.

- Test for operation of unit prior to returning to service.

5. Further Information

Please refer to the Chroma-Q®Space ForceTM manual for more detailed information. A copy of

the manual can be found at the Chroma-Q®website –www.chroma-q.com/support/downloads

Spacer

M3X20 Screw

Grommet

Space ForceTM octo LumenRadio Card QSG V2.0 QSG P/N: 650-0902

Approvals & Disclaimer

The information contained herein is offered in good faith and is believed to be accurate.

However, because conditions and methods of use of our products are beyond our

control, this information should not be usedinsubstitution for customer's tests to ensure

that Chroma-Q®products are safe, effective, and fully satisfactory for the intended end

use. Suggestions of use shall not be taken as inducements to infringe any patent.

Chroma-Q®sole warranty is that the product will meet the Chroma-Q®sales

specifications in effect at the time of shipment. Your exclusive remedy for breach of

such warranty is limited to refund of purchase price or replacement of any product

shown to be other than as warranted.

Chroma-Q®reserves the right to change or make alteration to devices and their

functionality without notice due to on-going research and development.

The Chroma-Q®Space ForceTM has been designed specifically for the lighting industry.

Regular maintenance should be performed to ensure that the products perform well in

the entertainment environment.

If you experience any difficulties with any Chroma-Q®products please contact your

selling dealer. If your selling dealer is unable to help, please contact

[email protected]. If the selling dealer is unable to satisfy your servicing needs,

please contact the following for full factory service:

Outside North America:

Tel: +44 (0)1494 446000

Fax: +44 (0)1494 461024

[email protected]

North America:

Tel: +1 416-255-9494

Fax: +1 416-255-3514

[email protected]

For further information please visit the Chroma-Q®website at www.chroma-q.com.

Chroma-Q®is a trademark, for more information on this visit

www.chroma-q.com/trademarks.

The rights and ownership of all trademarks are recognized

Inhaltsverzeichnis

Andere Chroma Beleuchtungsausrüstung Handbücher

Chroma

Chroma Studio Force V12 Bedienungsanleitung

Chroma

Chroma Space Force onebytwo LumenRadio Card Bedienungsanleitung

Chroma

Chroma Color One 100 Bedienungsanleitung

Chroma

Chroma Color Span 2 Bedienungsanleitung

Chroma

Chroma Sandi 1518-1000 Bedienungsanleitung

Chroma

Chroma Color Charge Bedienungsanleitung

Chroma

Chroma Color One 100 Bedienungsanleitung

Chroma

Chroma Color Force 48 Bedienungsanleitung

Chroma

Chroma Chroma-Q Bedienungsanleitung

Chroma

Chroma Space Force Bedienungsanleitung

Chroma

Chroma Cascade Bedienungsanleitung

Chroma

Chroma Color Charge Bedienungsanleitung

Chroma

Chroma Studio Force D Phosphor Bedienungsanleitung

Chroma

Chroma Inspire 632-5010 Bedienungsanleitung

Chroma

Chroma Inspire XT CHINHLRGBWXT Bedienungsanleitung

Chroma

Chroma Color One 100 638-1100 Bedienungsanleitung

Chroma

Chroma Color Split CHCS2 Bedienungsanleitung

Chroma

Chroma Studio Force D Compact Bedienungsanleitung

Chroma

Chroma Studio One 100 T Bedienungsanleitung

Chroma

Chroma Color Force Compact Bedienungsanleitung

Chroma

Chroma Space Force Bedienungsanleitung

Chroma

Chroma Sandi 1622 Bedienungsanleitung

Chroma

Chroma Plus Bedienungsanleitung

Chroma

Chroma Space Force CQSPFVLR Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung