CiA TVCD606 Bedienungsanleitung

Installation and Operation Manual

for

TVCD606

２

Please read the operation manual carefully

before installing and using this unit

１

I. Points for Attention

1. Before installing the omni bearing intelligent unit, please read the operation

manual carefully.

2. The camera takes power supply of DC12V/1.2A. You should assure that the power

supply of the product has an input voltage with load about 12V rather than a

unload voltage of 12V, otherwise the camera couldn’t work normally.

3. During the process of transportation, storage and installation, the dome should be

avoided of incorrect operations such as heavy pressing, strong vibration etc. which

can cause damage of product as there are sophisticated optical and electronic

devices inside the machine.

4. Do not attempt to disassemble the camera. In order to prevent electric shock, do

not remove screws or covers. There are no user serviceable parts inside and only

qualified personnel are to service the unit

5. Always follow all electrical standards for safety when it is in operation. Adopt the

particular power supply, which is provided with the dome. RS-485 and video

signal should keep enough distance with high voltage equipments and cables

when they are in transmission. Precautions for anti-lightning and anti-surging

should be taken if necessary.

6. The product should be indoor installed and operated to avoid rain and moisture. Do not use it

in wet places. If outdoor installation is needed, the closed protect cover should be used and it

is absolutely prohibited to use it in open air independently.

7. Do not operate it in case temperature, humidity and power supply are beyond the

limited stipulations.

8．Do not let the video camera aim at the sun or the object with extreme light

whatsoever it is switched on or not. Do not let the video camera aim at or monitor

bright and standstill object for a long time.

9. Do not use aggressive detergent to clean the main body of the video camera.

Wipe dirt with dry cloth. If needed, mild detergent can be used suitably.

10. Operate the intelligent high-speed spherical video camera with great care to

avoid shock or vibration. It operate incorrectly, machine could be damaged.

11. Install the video camera in the place where endurance should be enough large.

12. Should be dust on the lens, you should wipe it with special lens tissue.

２

II. Description of Functions

The dome camera is a hi-tech CCTV product, which incorporates color TV, omni

bearing dome P/T and multifunctional decoder into a whole. It can largely reduce

connection and installation processes of components in the system, rise up reliability

of the system and facilitate installation and maintenance. Therefore it has advantages

of beautiful appearance, compact structure and easy operation.

1. Integrated Multi-Protocol Decoder

a. With built-up decoder and integrated multi-protocol, it can integrate 16 kinds

of communication protocols in maximum. As its baud rate of communication

can be adjusted, it is compatible with main domestic and foreign systems by

easy setting inside the spherical camera, so it has stronger versatility.

b. RS485 serial control: addresses of the dome camera 1-1023.

2. Integrated Omni bearing dome P/T

a. Turning 360ºhorizontally and continuously with unlimited positions. PAN

speed range:0～15rad/s (constant speed dome PAN: 15rad/s); turning 0～90º

vertically with a speed 0～15rad /s(constant speed dome TILT: 15rad/s).

b. Running stably at low speed with super lower noise. Pictures have no

shaking.

c. the location precision up to ±0.2°.

3. High Intelligent Degree

a. Support the dome camera to scan horizontally between two points and scan

speed can be modified.

b. Data can be stored with powerless memory.

4. Newly-Added Functions

a. Flexible and Convenient Application: there are many communication

protocols integrated inside the spherical camera and the baud rates can be

selected from 24000 bps to 19200 bps.

5. Selectable Optical Zoom Range of Camera

Times of Optical

Zooming Focus Range Lowest Illuminance

16x f3.9-f6.3 mm 1 Lux (F1.4)

18x f4.1-f73.8 mm 1 Lux (common type) / 0.01 Lux（day & night type）

22x f4-f88 mm 0.2 Lux（F1.6 1/3s）

23x f3.6-f82.8 mm 1 Lux (Common type) / 0.01 Lux（day & night type）

25x f3.6-f90 mm 1 Lux (Common type) / 0.01 Lux（day & night type）

３

III. Settings of Special Camera

Before installing the spherical camera, please confirm the communication protocol

and baud rate the master controler in the system uses, then set the coding switches on

the back of the camera to be identical with that of the system in which SW1 is for

address of the spherical camera and SW2 is for communication protocol and baud rate

(see attached tables 1,2 and 3).

31 2

Pr ot ocol Sel ect

1234 5 678 910

SW1

Speed Dome Addr ess Sel ect

1234 5 6

SW2

120Ω termi nal resi stor i s connected on RS485 Bus

120Ω termi nal resistor i s opened f or RS485 bus

31 2ID-CODE S e t

Sy s t e m

cont r ol wi r e

JP1 is jumper for the terminal resistor

JP1 is the 120 Ωterminal resistor for RS485 Bus. When short-circuit terminal is set between

“1-2”, the 120 Ωterminal resistor is opened while it is set between “2-3”, the resistor is

connected. Take care that on RS 485 Bus only one farthest spherical camera has the terminal

resistor connected while other devices should have their terminal resistors opened.

zSettings of Addresses of dome Cameras

States of Coding SwitchesDome

Addres

s DIP-

DIP-

DIP-1

1 ON OFF OFF OFF OFF OFF OFF OFF OFF OFF

2 OFF ON OFF OFF OFF OFF OFF OFF OFF OFF

3 ON ON OFF OFF OFF OFF OFF OFF OFF OFF

4 OFF OFF ON OFF OFF OFF OFF OFF OFF OFF

5 ON OFF ON OFF OFF OFF OFF OFF OFF OFF

6 OFF ON ON OFF OFF OFF OFF OFF OFF OFF

7 ON ON ON OFF OFF OFF OFF OFF OFF OFF

8 OFF OFF OFF ON OFF OFF OFF OFF OFF OFF

9 ON OFF OFF ON OFF OFF OFF OFF OFF OFF

10 OFF ON OFF ON OFF OFF OFF OFF OFF OFF

11 ON ON OFF ON OFF OFF OFF OFF OFF OFF

12 OFF OFF ON ON OFF OFF OFF OFF OFF OFF

13 ON OFF ON ON OFF OFF OFF OFF OFF OFF

14 OFF ON ON ON OFF OFF OFF OFF OFF OFF

15 ON ON ON ON OFF OFF OFF OFF OFF OFF

16 OFF OFF OFF OFF ON OFF OFF OFF OFF OFF

17 ON OFF OFF OFF ON OFF OFF OFF OFF OFF

18 OFF ON OFF OFF ON OFF OFF OFF OFF OFF

……………………………

1023 ON ON ON ON ON ON ON ON ON ON

４

Table 1

For Example:

Speed Dome Addr ess=1

1234 5 6

78910

Speed Dome Addr ess=2

1234 5 6

78910

Speed Dome Addr ess=3

1234 5 6

78 910

Speed Dome Addr ess=4

1234 5 6

78910

Speed Dome Addr ess=18

1234 5 6

78910

Sp e e d Do me Addr ess=1023

1234 5 6

78910

Notes:

1. Addresses of the dome cameras are denoted by binary code system. ON means

“1” while OFF means “0”.

2. Above coded addresses are only from no.1 to no.20. The codes of addresses from

no.21 to no.1023 can be deduced by analogue.

3. The range of addresses of the spherical cameras is from 1 to 1023.

zSettings of communication protocol of the dome camera (DIP1-DIP4 of SW2)

and its default baud rate (DIP5-DIP6 of SW2). In case the default baud rate of the

dome camera is not in accordance with that of the controller, please reset it as per

the Table 3 (●means the protocol has been done).

Selection of Protocols Normal Baud Rate

Type of Protocols DIP-1 DIP-2 DIP-3 DIP-4 DIP-5 DIP-6

Integrated

Protocol

Minking A01 OFF OFF OFF OFF ON OFF ●

Minking B01 ON OFF OFF OFF OFF ON ●

Santachi OFF ON OFF OFF OFF ON ●

PELCO-D ON ON OFF OFF OFF OFF

●

PELCO-P/4800 ON OFF

PELCO-P/9600 OFF OFF ON OFF OFF ON ●

PANASONIC ON OFF ON OFF OFF ON ○

Longcomity OFF ON ON OFF OFF ON

●

HUNDA600 ON ON ON OFF OFF ON

●

LILIN OFF OFF OFF ON ON OFF

○

VICON ON OFF OFF ON ON OFF

○

MOLYNX OFF ON OFF ON OFF ON ○

KALATEL ON ON OFF ON ON OFF ○

VCL OFF OFF ON ON OFF ON ○

DAIWA ON OFF ON ON OFF ON ○

ALEC OFF ON ON ON OFF ON

○

Utralk ON ON ON ON OFF ON

○

Table 2

Protocols mentioned above are suitable for the dome camera. Among them “Santachi”,

“ PELCO-D” and “PELCO-P” have no corresponding orders for some special

functions in the protocols. In order to control some special functions of the spherical

camera, we make some functional transformation upon some common orders.

Normally we take “Call Preset Position / Set Preset position” to transform, and

contents of order transformation are listed below.

５

Definition of Keypad Operation

Number

of N

Value

Control Object

Call No. N Preset Point Set No. N Preset Point

51 Start Scan (low Speed) Start Patrol

52 Start Scan (middle Speed) Set Start Position of Scan

Supplementary Control of

dome Start Scan (high Speed) Set End Position of Scan

54 Power Supply of Camera Power Supply On Power Supply Off

55 BLC On Off

56 Zero Illuminance On Off

57 Screen Display * On Off

58 D-Zoom On Off

59 Focus Automatic Manual

60 Iris Automatic Manual

61 Automatic Manual

62 Interior Exterior

Mode of White Balance *

ATW One Push WB

Notes:

1. Those Items with “*” have memory function even the dome is switched off.

2. For those cameras with “menu”, you can use “Screen Display ON” to control the

Menu ON/OFF, and use “Screen Display OFF” to control Screen Display

ON/OFF.

3. For those cameras which have no “Zero Illuminance” or the function of “Zero

Illuminance” is automatically switched without control, then above “Zero

Illuminance” is invalid.

4. Notes to “Patrol” Function of the dome camera:

①Automatically scan from no.1 to no.16 preset points one by one. If some

points do not have been preset or are cleared out after presetting, they will be

bypassed when patrol is carrying out.

②The dwelling time between to preset points is 4 seconds.

③The “Patrol” function of the dome camera can be carried out by presetting

no.51 position.

5. Notes to “Scan(auto pan)” Function of the dome camera:

①The dome camera makes automatic scan between two specified positions.

②The speeds of scan are divided into three levels. You can call no. 51, 52 and

53 preset position to start scan at speed of 1.5°/ sec, 5°/ sec and 10°/ sec

separately.

③The dwelling time between the “Start Point” and “End Point” of scan is 3

seconds.

6. All notes mentioned above are supplementary descriptions under high speed. All original

operations of the control system are unchanged.

zSettings of Communication Baud Rate of the dome Camera

６

IV. Steps of Installation

1. M ounting Base

2. Outer Tube

3. Shading Cover

4. Outer Cover

5. Camera

6. Connecti ng Cabl e

Dimension Drawing

1. Carefully read the operation manual and the points for attention.

2. Carefully set the communication code, baud rate and address of the dome camera

and make confirmation they are correct.

3. Take out the plug of the dome camera and connect external power supply, RS485

and video wires as per marks on the plug. Take care that the power supply of the

dome camera is DC12V/1.2A and adopt the particular power supply which is

provided with the dome camera.

Red : DC12V+

Black : GND

Orange : RS485+

Yellow : RS485-

VIDEO

4. Take out the mounting base from the spherical camera, thread the connecting

wire from behind through the central hole of the base. Fix the base by three

screws on the ceiling as per the drawing, and connect the wire with the ball. Aim

the latch in the ball with the notch on the base as per the drawing, and mount the

ball upward to the position and turn it clockwise until the spring sheet on the

base takes effect. In case the wire could not come out from behind the ceiling,

you can open a hole on the edge of the casing for running of the wire.

CodingSwitch

Baud Rate 1 2 3 4 5 6

2400 bps OFF OFF

4800 bps ON OFF

9600 bps OFF ON

19200 bps ON ON

７

Installation Drawing

V. Main Technical Data

Image

Inductor 1/4″Color CCD

Effective

Pixels 752H×582V（440000pixels）PAL

Synchronous

System Internal Synchronization

VF Output Compound Signal 1.0Vp-p/75Ω

White Balance Automatic/Manual

Power Supply DC12V±10% 1.2A

Power

Consumption 12VA

Weight 2Kg

Mounting

Style Ceiling or ceiling hanging style

Relative

humidity 10-75%（under no condensing）

Specifications

Operation

Temperature 0℃~40℃

Scan System 15.625KHz(H) 50Hz (V)

Horizontal

Resolution 480 TV lines

Signal / Noise

ratio Larger than 48 db

Electronic

Shutter 1/3～1/10000 seconds

Camera Function

Lowest

Temperature 1Lux，AGC ON

Lens Data Zooming

Range 18×Optical and 12×Digital

８

Iris Automatic/Manual

Focus Automatic/Manual

Horizontal

Turning 0--15°/s (constant P/T: 15°/s fixed)

Vertical

Turning 0--15°/s (constant P/T: 15°/s fixed)

Preset

Positions 64 presets (max)

Basic Functions

of Spherical

Camera

Patrol

Function At best 6 cruises

VI. Analysis of Normal Troubles

Problems Possible Causes Remedies

Power supply damaged or

insufficient power Replace

Wrong connection of power

supply Correct

No action and images when

power is switched on

Faults in engineering circuits Remove

Mechanical fault Repair

Tilting camera Place uprightly

Abnormal self-inspection.

Images with roaring sound of

the motor Insufficient electrical power

Replace with qualified power

supply and let it close to the

spherical camera

Wrong connection of VF

circuit Correct

Bad connection of VF circuit Remove

Normal self-inspection but no

images

Camera damaged Replace

Wrong connection of control

signal wire Correct

Mismatched address of

spherical camera Reselect

Successful self-inspection but

out of control

Mismatched protocol

Adjust protocol to match with

the controller and switch on

again

Bad connection of VF circuit Remove

Images unstable Insufficient electrical power Replace

Abnormal self-inspection Switch on again

Bad connection of control wire Remove

Problems on main frame Switch on the main frame

Dome Camera out of control

Too heavy load or longer

distance of communication

1．Connect 120Ωresistor to

the farthest camera and let

other cameras to be

broken；

2．Increase code distributor.

Normal problems and their causes and remedies mentioned above are only for

reference. Should you meet other special problems, you can ask for technical

support from your dealer directly.

Inhaltsverzeichnis

Andere CiA Sicherheitskamera Handbücher

CiA

CiA TVCD 506 Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung