Cielsa Dawn E021 Bedienungsanleitung
INSTALLATION
AND USER GUIDE
APPLICABLE MODEL:E021
Installtion for electronic door lock
Please read this manual before installing.
TABLE OF CONTENT
CHECK AND PREPARATION
INSTALLTION STEPS
INSTRUCTION OPERATION
SAFETY PRECAUTIONS
WELCOME
Required tools
This guide will walk you through step-by-step how to
install and get your product up and running.
Installation generally takes less than 30 minutes.
If you have any questions, please feel free to contact
us.
Check and preparation
Check dimensions
remove existing deadbolt or use provided template to bore new holes
Before getting started, ensure the package contains the following components
CHECK AND PREPARATION INSTALLTION STEPS INSTRUCTION OPERATION
How to bore new holes?
Put the template on the door panel as shown in the
drawing.
use the Template as an indication to mark the centre of
the circle on the door face and the centre of the door
edge.
Use the marks as a guide to drill holes
Drill the striker plate & strike box hole
a. Close the door, mark the top and bottom ends of the lock edges on the door frame, and draw a
centerline.
b. mark and drill a 1’’x4/5’’ (27x20mm) hole for striking plate box, with depth of 1’’(25.4mm).
c. Mark and drill a 2-6/24’’x1’’(58x25.4mm) hole for striking plate.
d. Fix striking plate box and striking plate with 2pcs 3/4’’ (19mm) screw.
CHECK AND PREPARATION INSTALLTION STEPS INSTRUCTION OPERATION
Installation Steps
ADJUST DEADBOLT AND INSTALL
1
Insert the deadbolt into mortise.Secure with
2 screws.
CHECK AND PREPARATION INSTALLTION STEPS INSTRUCTION OPERATION
Possi doluptam et parchitatur rempore,
volum versper eprovitatiae exerchi llander-
it vid quis cus eostin pra vel essitibusdam
qui vellupturi omniae venihit lab.
2INSTALL THE KEYPAD
Install front panel and front panel silicon pad,
make sure the latch bolt be contracte.
3FIXING OF REAR PANEL
Pass the IC wire and the latch link bar to
mounting plate.
Use the screws as shown in the gure con-
nect rear panel xing plate with latch and
door.
Note: Please place the IC line as shown in
the gure to avoid the lock latch out of con-
trol.
CHECK AND PREPARATION INSTALLTION STEPS INSTRUCTION OPERATION
INDENTIFY DOOR HANDING
4
The door is “Left-handle” if the hinges are on the
left side of the door.
The door is “Right-handle” if the hinges are on
the right side of the door.
Turn the piece as shown
Rotate the thumb turn piece as shown
CHECK AND PREPARATION INSTALLTION STEPS INSTRUCTION OPERATION
Rotate the thumb turn piece as shown
Install the rear panel.
Use the screws as shown connect rear panel
with latch and rear panel fixing plate.
INSTALL REAR PANEL:
5
Docking of the connector.
Pay attention to the direction of the inserted
connector.
• Turning the knob control the deadbolt.
• Hold down the back lock switch for 3s until a
“beep” sound is heard, thus enabling the anti-lock
state.In this case,only admin code can unlock in
the outside.Inside, turn the knob to release the
anti-lock and 2 beeps sound.
CHECK AND PREPARATION INSTALLTION STEPS INSTRUCTION OPERATION
When you complete the installation, follow this step to set the lock:
Ⅰ
SYSTEM SIGNALS
Instruction operation
use cases Sound Light
Correct user code entered to unlock 3 short beeps Blue ashes
Successfully locked 3 short beeps Blue ashes
Incorrect user code entered 4 short beeps white ashing
Successful programming 2 short beeps None
Unsuccessful programming 4 short beeps white ashing
Verication is correct or programming ends
successfully
1 long beeps None
Low battery alarm 4 short beeps None
Factory mode restored successfully 5 short beeps with
1 long beeps
white ashing with
green ashes
5 incorrect user codes entered 4 long beeps None
Registration ngerprint Every press of ngerprint 2 short beeps
Registration successful 1long beep
Registration failed 4 short beeps
Registration process blue ashes
Registration successful green ashes
Registration failed red ashes
Correct ngerprint unlock 3 short beeps green ashes
Incorrect ngerprint unlock 4 short beeps red ashes
TEST SYSTEM RESETTING ADD ADMIN CODE ADD GENERAL
USER’S CODES
CHECK AND PREPARATION INSTALLTION STEPS INSTRUCTION OPERATION
Andere Handbücher für E021
1
Andere Cielsa Dawn Türschloss Handbücher
