cinetto B-MOVED Bedienungsanleitung
1Assembly Instructions CinettoB-moved.
1. Initial condition of the wardrobe
Do not plug the control unit to electricity before connecting all the engines (see connections at pages 4-5-
6-7).
Connect all the electric motors of the transmission bars to the control unit according to the wardrobe con guration.
After connecting all the electric motors to the control unit close manually all the doors.
2. Control unit power supply
After connecting all the
electric motors to the
control unit and after closing
manually all the doors is
possible to connect the
control unit to the power
supply.
After connecting to the power supply, wait at least 10 seconds, to allow to the control unit to
check the wardrobe con guration.
3. Self-learning cycle
Start the self-learning cycle to make the
automatic set-up of the run of the doors
pressing at least 3 seconds the “SET /
RESET” button on the power unit. All the
doors, one by one, starting from the rst left
door on the wardrobe, will move at reduced
speed until their nal stoppers.
This operation, until all the doors record their
run, may take some minutes.
During the self-learning cycle do not
stop or put obstacles towards the doors
and keep the door’s run free.
If the position of the nal stoppers
is modi ed, please repeat the self-
learning cycle again.
Quick start installation and setup
00:00:10
SET/
RESET
00:00:03
2 3Assembly Instructions CinettoB-moved.
6. General check of the system
Check that the movement of the doors work properly.
Check the safety system against accidental crush, putting an obstacle between the door while closing and the side
of the furniture.
Make this check to prevent danger or damage determined by a wrong operation of the system.
SOURCE
DEVICE
DEVICEDEVICE
0 - 48
N/O
SWITCH
During the self-learning cycle the pairing with the remote control is not working.
If the self-learning cycle is not working, because of lack if electricity or for the presence of obstacles disconnect
from the power supply, close manually the doors and start the self-learning cycle again.
4. Pairing of the remote control
To activate the pairing function, press and
release the “REMOTE SET” button on the
control unit. Then a red LED will ash
on the control unit. While the LED
is ashing, press for at least 3
seconds one of the buttons of
the remote control to pair it.
Multiple control units
can be paired and used
with a single remote
control.
Multiple remote controls
can be paired and used
with the same control
unit.
Pairing must not be activated
during the track memorization
cycle.
To unpair the remote control unit, press and release the
“REMOTE SET” button, after which the red LED will ash.
Press the “REMOTE SET” button again and keep it pressed
until the led stops ashing. When the button is released, the
red LED will ash 5 times to con rm the unpairing.
The unpairing of a remote control completely eliminates its
association with any control unit. In order to use the remote
control, it will be necessary to pair it again using the standard
procedure.
5. Wiring of the switch on the control unit
The N.O. switch is a normally-opened electric contact, managed by the
control unit.
There is no electric tension on the terminals of the switch. The switch isn’t
a voltage supply.
The switch can manage devices with nominal tension between 0
and 48V and a maximum electric current of 2A.
The wiring between the switch and the devices must be performed
by specialized personnel according to the following scheme.
REMOTE
SET
00:00:03
FREQUENCY: 433,92 MHZ
MAX POWER: 1 mW
DEVICE = 0 - 48V
MAX 2A
SWITCH
N/O
O
I
SOURCE
DEVICE
DEVICE
0 - 48V
MAX 2A
N/O
SWITCH
4 5Assembly Instructions CinettoB-moved.
Wardrobe confi gurations with coplanar doors PS40 & B-MOVED
CONNECTIONS
11
1 4
ALWAYS
SYNCHRONIZED
1 2 3 4
S
S
32
S
E
G
F
A
S = synchronized
6 7Assembly Instructions CinettoB-moved.
Wardrobe confi gurations with overlapping doors PS48 & B-MOVED
CONNECTIONS
122
1
1 3
2
C
B
*Central door opening just
to the left.
32
S
F
1 4
2 3
ALWAYS
SYNCHRONIZED
S
S
G
S = synchronized
8 9Assembly Instructions CinettoB-moved.
1
1
Confi gurations for retractable doors PS66 & B-MOVED
CONNECTIONS
A
11
S
B
S = synchronized
10 11Assembly Instructions CinettoB-moved.
23
S
BConfi gurations for vertical concealed doors PS70 & B-MOVED
CONNECTIONS
1
S = synchronized
12 13Assembly Instructions CinettoB-moved - Wave Sensor.
Before installing Wave Sensor, it is necessary to have installed the B-moved electrical system.
PS40 & B-MOVED
W1 W1
ACONFIGURATION
14 15Assembly Instructions CinettoB-moved - Wave Sensor.
W3W2
W3W1W2 W1
FCONFIGURATION
W1 = synchronized opening
W1 W4
ECONFIGURATION
16 17Assembly Instructions CinettoB-moved - Wave Sensor.
W2 W4 W1 W1 W4 W3
W2 W1 W1 W3
GCONFIGURATION
W1, W4 = synchronized opening
W1 = synchronized opening
W1W1
W1 = synchronized opening
18 19Assembly Instructions CinettoB-moved - Wave Sensor.
W1 W2 W2
W1
B
PS48 & B-MOVED
CONFIGURATION
W4 W1 W1 W4
W1, W4 = synchronized opening
Dieses Handbuch passt für folgende Modelle
7
Andere cinetto Steuerungssystem Handbücher
