Cisco SPA232D Bedienungsanleitung

Quick Start Guide

Cisco SPA232D Mobility Enhanced ATA

Package Contents

•Analog Telephone Adapter

•Ethernet Cable

•Phone Cable

•Power Adapter

•Quick Start Guide

•Product CD-ROM

2 Cisco SPA232D Quick Start Guide

Welcome

Thank you for choosing a Cisco SPA232D Mobility Enhanced ATA.

This guide describes how to physically install the equipment and how to

get started configuring the ATA.

This guide also explains how to register a Cisco SPA302D Mobility

Enhanced Cordless Handset with the Cisco SPA232D, which has an

integrated DECT Base Station. Cisco SPA302D handsets registered to the

Cisco SPA232D can make and receive calls through a Voice over IP (VoIP)

service provider and through the local telephone system (via the LINE

port). Only Cisco SPA302D handsets are supported with the Cisco

SPA232D.

Before You Begin

Before you begin the installation, make sure that you have the following

equipment and services:

•An active Internet account and Voice over IP account

•Ethernet cable to connect to your broadband network device

•Phone to connect to your ATA

•Phone cable to connect your phone

•Optional: Uninterruptible Power Supply (UPS) to provide backup power

•Optional: Cisco SPA302D Mobility Enhanced Cordless Handsets

Cisco SPA232D Quick Start Guide 3

Product Features

Top Panel

Back Panel

Feature Description

Page/

Registration

Steady green—One or more handsets is registered.

Fast flashing green—The base is in registration mode.

To activate registration mode, press the button for at

least 7 seconds.

Slow flashing green—The base is in paging mode or a

handset is off hook. To activate paging mode to locate a

handset, press the button for a few seconds; handsets

ring.

Off—No handset is registered to the base.

LINE

Steady green—The line is off hook and connected to

the local telephone system.

Slow flashing green—The line is off hook.

Off—The port is not ready.

PHONE

Steady green—The device is on hook and registered to

a SIP proxy.

Slow flashing green—The device is off hook.

Off—The port is not ready.

INTERNET

Flashing green—Transmitting or receiving data through

the WAN port.

Off—No link.

SYSTEM

Steady green—The system is ready.

Slow flashing green—Acquiring an IP address, if

applicable. (DHCP is used by default.)

Fast flashing green—Upgrading the firmware.

Off—There is no power or the system cannot boot up.

Feature Description

RESET Performs two functions:

Restart the ATA: Press quickly (less than a second)

with a paperclip or similar object.

Restore the factory default settings: Press and hold

for 10 seconds.

LINE (Green) Connects to an analog phone line, using an RJ-11

phone cable.

4 Cisco SPA232D Quick Start Guide

Default Settings

PHONE (Gray) Connects to an analog phone, using an RJ-11 phone

cable.

ETHERNET

(Yellow)

Connects to a device on your local area network (LAN),

such as a computer by using an Ethernet cable.

INTERNET (Blue) Connects to a broadband network device (DSL or

cable modem) or a network router by using an Ethernet

cable.

POWER Connects to a power by using the provided adapter.

Parameter Default Value

Administrator Username admin

Administrator Password admin

User Username cisco

User Password cisco

Internet Connection Type Automatic Configuration - DHCP

LAN IP Address

(Also the address for the web-

based configuration utility.)

192.168.15.1

DHCP Range

(DHCP server enabled by default.)

192.168.15.100-149

Netmask 255.255.255.0

PIN for handset registration, IP

settings, and SIP settings

Blank

Feature Description

Cisco SPA232D Quick Start Guide 5

Connecting the Equipment

NOTE For wall-mounting instructions, see Additional Information, page 8.

STEP 1Connect the provided Ethernet cable to the INTERNET (Blue) port.

Connect the other end of the cable directly to your broadband

network device.

STEP 2Connect the provided phone cable to the PHONE 1 (Gray) port.

Connect the other end of the cable to your analog phone or fax

machine.

STEP 3Optionally, connect an Ethernet network cable to the ETHERNET

(Yellow) port of the ATA. Connect the other end of the cable to a

device on your network, such as a computer.

STEP 4Connect an analog phone line to the LINE (Green) port to connect

the ATA to your local telephone system.

STEP 5Connect the provided power adapter to the POWER port. The unit

powers on.

239756

WAN

6 Cisco SPA232D Quick Start Guide

Configuration and Management of the ATA

You can use the web-based configuration utility to set up your ATA. You

also can use the built-in Interactive Voice Response (IVR) system. (See

Using the IVR for Administration, page 8.)

STEP 1Connect the provided Ethernet network cable to the ETHERNET

(Yellow) port of the ATA. Connect the other end of the cable to the

Ethernet port of your PC.

STEP 2Power on your computer.

NOTE: Make sure your computer’s Ethernet adapter is set to obtain

an IP address automatically (DHCP). For more information, refer to

the Help for your operating system.

STEP 3Start a web browser on your computer.

STEP 4In the Address bar, enter: 192.168.15.1

Note: 192.168.15.1 is the default local IP address of the ATA.

STEP 5To log in for the first time, enter the default username, admin, and

the default password, admin. The password is case sensitive.

NOTE: A user account allows access to limited settings and status

pages. To log in as a user, enter cisco as the username and the

password.

STEP 6Use the Quick Setup page as needed to register your VoIP

accounts in the fields for Line 1 and DECT Line1.

Your VoIP service may require only a few basic parameters to

successfully register the Cisco SPA232D. The Quick Setup page

offers a shortcut to enter the basic parameters. For a more

comprehensive listing of parameters, choose the Voice menu, and

then use the links in the navigation tree.

•EnterProxy:Enter the domain name or URL of the service

provider’s proxy server.

•DisplayName:Enter the name of the business. This name

typically is used for the Caller ID.

•UserID:Enter the user ID for your Internet account with this

service provider.

•Password:Enter the password for your Internet account.

• Dial Plan (Line 1 only): Keep the default settings

(recommended). Detailed information about the dial plan

settings is available in the online Help and the administration

guide.

Cisco SPA232D Quick Start Guide 7

Note: The Cisco SPA232D assigns DECT Line1 as the default line

for outgoing calls from Cisco SPA302D handsets. If needed, you

can configure additional VoIP accounts as separate “DECT Lines.”

To do so, choose the Voice menu, and then use the DECT Line

1~10 links in the navigation tree. Use the check boxes on the Quick

Setup page to associate the DECT Line(s) to each handset.

STEP 7Click Submit to save your settings.

STEP 8If you wish to change the PIN for handset registration, open the

Voice > System page, and then enter up to four digits in the IVR

Admin Password field. Click Submit to save your settings.

For more information, see the online Help or the administration guide.

(Documentation links are provided in Where to Go From Here, page 14.)

Registering a Cisco SPA302D Handset

You can register Cisco SPA302D handsets to the integrated DECT base

station. These handsets can be purchased separately.

STEP 1On the Cisco SPA302D handset, press the center Select button on

the 4-way navigation keypad.

STEP 2Select Register.

STEP 3Using the navigation arrows, scroll to the Settings icon

and press the center navigation button to select it.

STEP 4Select Handset Registration.

STEP 5On the Cisco SPA232D, press the Page/Registration button and

hold it down for at least seven seconds until the green status light

flashes quickly.

TIP: If you press the button for fewer than seven seconds, the

green status light flashes slowly, indicating the unit is in “paging”

mode and is not in registration mode. Registration will not work if

the unit is in paging mode.

STEP 6The default PIN is blank, so do not enter a PIN. Press the left

softkey to confirm that you want to register the handset. The

“registering” message appears.

8 Cisco SPA232D Quick Start Guide

STEP 7To verify that the handset registered to the base station, confirm

that the wireless status icon is solid and that the handset ID, such

as DECT1 or DECT 2, appears near the top right corner of the

display screen.

Additional Information

Using the IVR for Administration

An IVR system is available to help you to configure and manage your ATA.

You can use the telephone keypad to select options and to make your

entries.

To access the IVR menu:

STEP 1Connect an analog phone to the PHONE port of the ATA.

STEP 2Press the star key four times: ****

STEP 3After the greeting plays, press the keys on the phone keypad to

select your options.

STEP 4Enter the code for the desired action. See the IVR Actions table for

details.

TIPS:

• Enter the numbers slowly, listening for the audio confirmation before

entering the next number.

• After you select an option, press the #(pound) key.

• To exit the menu, hang up the telephone or enter 3948# to exit.

• After entering a value, such as an IP address, press the #(pound) key to

indicate that you have finished your selection. To save the new setting,

press 1. To review the new setting, press 2. To re-enter the new setting,

press 3. To cancel your entry and return to the main menu, press *(star).

• While entering a value, you can cancel the changes by pressing the *

(star) key twice within half a second. Be sure to press the key quickly, or

the *will be treated as a decimal point entry.

• If the menu is inactive for more than one minute, the ATA times out. You

will need to re-enter the menu by pressing the star key four times: ****.

Your settings take effect after you hang up the telephone or exit the IVR.

The ATA may reboot at this time.

Cisco SPA232D Quick Start Guide 9

•To enter the decimal points in an IP address, press the *(star) key. For

example, to enter the IP address 191.168.1.105, perform the following

tasks:

–Pressthesekeys:191

*168*1*105.

–Pressthe#(pound) key to indicate that you have finished

entering the IP address.

–Press1to save the IP address or press the *(star) key to cancel

your entry and return to the main menu.

IVR Actions

IVR Action Menu

Option

Choices and Instructions

Enter IVR Menu ****

Check Internet Connection

Type

100

Set Internet Connection

Type

101 DHCP: 0

Static IP: 1

PPPoE: Press 2

Check Internet IP Address

(WAN port)

110

Set Static IP Address (WAN) 111 Enter the IP address by using

numbers on the telephone

key pad. Use the *(star) key

when entering a decimal

point.

Note: This option is available

only after you choose Static

IP as the Internet Connection

Type, through option 101.

Check Network Mask 120

Set Network Mask 121 To enter the value, press

numbers on the telephone

key pad. Press the * (star) key

to enter a decimal point.

Note: This option is available

only after you choose Static

IP as the Internet Connection

Type, through option 101.

10 Cisco SPA232D Quick Start Guide

Check Gateway IP Address 130

Set Gateway IP Address 131 To enter the value, press

numbers on the telephone

key pad. Press the * (star) key

to enter a decimal point.

Note: This option is available

only after you choose Static

IP as the Internet Connection

Type, through option 101.

Check MAC Address 140

Check Firmware Version 150

Check Primary DNS Server

Setting

160

Set Primary DNS Server 161 To enter the value, press

numbers on the telephone

key pad. Press the * (star) key

to enter a decimal point.

Note: This option is available

only after you choose Static

IP as the Internet Connection

Type, through option 101.

Check Internet web server

port

170

SPA122 only: Check LAN IP

address (Ethernet port)

210

Announce Line 1 SIP

Transport

1910

Set Line 1 SIP Transport 1911 0: UDP

1: TCP

2: TLS

Check Line 2 SIP Transport 1920

Set Line 2 SIP Transport 1921 0: UDP

1: TCP

2: TLS

Exit IVR 3948

IVR Action Menu

Option

Choices and Instructions

Andere Handbücher für SPA232D

Inhaltsverzeichnis

Andere Cisco Adapter Handbücher

Cisco

Cisco PA-2FE-TX Bedienungs- und Wartungsanleitung

Cisco

Cisco WUSB54GS Bedienungsanleitung

Cisco

Cisco LINKSYS USB1000 Bedienungsanleitung

Cisco

Cisco Linksys WUSB54G Bedienungsanleitung

Cisco

Cisco AIR-CB21AG-W-K9 Bedienungsanleitung

Cisco

Cisco AIR-PCM340 Bedienerhandbuch

Cisco

Cisco Linksys RT31P2 Bedienungsanleitung

Cisco

Cisco Linksys PLS300 Bedienungsanleitung

Cisco

Cisco AIR-CB21AG-W-K9 Bedienerhandbuch

Cisco

Cisco Linksys USBBT100 Bedienungsanleitung

Cisco

Cisco SPA100 Series Bedienungsanleitung

Cisco

Cisco PA-F/FD-MM Bedienungs- und Wartungsanleitung

Cisco

Cisco SPA112 Bedienungsanleitung

Cisco

Cisco Aironet CB20A Bedienungsanleitung

Cisco

Cisco PLE300 Bedienungsanleitung

Cisco

Cisco DTA50 Bedienungsanleitung

Cisco

Cisco SPA112 Bedienungsanleitung

Cisco

Cisco ATA 191 Bedienungsanleitung

Cisco

Cisco PA-2JT2 Bedienungs- und Wartungsanleitung

Cisco

Cisco WAE-INLN-4CG Series Bedienungsanleitung

Cisco

Cisco WUSB100 Bedienungsanleitung

Cisco

Cisco SPA112 Bedienungsanleitung

Cisco

Cisco Linksys PAP2 Leitfaden

Cisco

Cisco PA-100VG Bedienungs- und Wartungsanleitung

Beliebte Adapter Handbücher anderer Marken

PCB Piezotronics

PCB Piezotronics 090B274 Bedienungsanleitung

Auvidea

Auvidea J20 Produkthandbuch

Gossen MetraWatt

Gossen MetraWatt AT3-III E Bedienungsanleitung

Akribis

Akribis ITF-21-BISS-MIT Bedienungsanleitung

Tenda

Tenda W54U Bedienungsanleitung

ROHO

ROHO AGILITY Bedienungsanleitung

PROLiNK

PROLiNK WN2001 Bedienungsanleitung

Hawking

Hawking HUF2 Bedienungsanleitung

Airlink101

Airlink101 AWLC4030 Bedienungsanleitung

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Bedienungsanleitung

Philips

Philips SWA4554S/10 Bedienungsanleitung

JVC

JVC TS-C9D2B Gebrauchsanweisung

NETGEAR

NETGEAR A6100 Bedienungsanleitung

D-Link

D-Link DWA-121 Bedienungsanleitung

Philips

Philips SWA2037 Bedienungsanleitung

Basalte

Basalte 0610-20 Bedienungsanleitung

Yealink

Yealink EHS40 Bedienungsanleitung

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Bedienungsanleitung