Cisco Aironet AIR-ANT1949 Bedienungsanleitung

Corporate Headquarters:

Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA

Cisco Aironet 13.5-dBi Yagi Mast Mount Antenna

(AIR-ANT1949)

Overview

This document describes the 13.5-dBi Yagi mast mount antenna and provides instructions for mounting

it. The antenna operates in the 2.4- to 2.5-GHz frequency range and is designed for point-to-point

communications. The antenna is a completely enclosed 16-element, vertically polarized directional Yagi

and is designed to be mounted outdoors on a mast. The antenna can also be used indoors and can be

mounted on a flat vertical surface, such as a wall.

The following information is provided in this document.

•Technical Specifications, page 2

•System Requirements, page 2

•Installation Notes, page 4

•Choosing a Mounting Location, page 5

•Tools and Equipment Required, page 5

•Mounting the Antenna, page 6

•Obtaining Documentation and Submitting a Service Request, page 8

Cisco Aironet 13.5-dBi Yagi Mast Mount Antenna (AIR-ANT1949)

78-14720-02

Technical Specifications

System Requirements

This antenna is designed for use with Cisco Aironet access points and bridges but can be used with any

2.4-GHz Cisco Aironet radio device that uses a reverse-polarity threaded naval connector (RP-TNC).

Antenna type Yagi

Operating frequency range 2400 – 2484 MHz

Nominal input impedence 50Ω

1.5:1 VSWR bandwidth 2400 – 2485 MHz

Environment Outdoor/indoor

Gain 13.5 dBi

Polarization Vertical

H-Plane (3dB bandwidth) 30°

V-Plane (3dB bandwidth) 30°

Cable length and type 3 ft. (0.91 m)

Plenum rated

RG-58

Dimensions (H x W) 16.5 in. x 3 in.

(41.9 cm x 7.6 cm)

Wind rating 125 MPH

(201.2 KMH)

Azimuth Radiation Pattern Elevation Radiation Pattern

81016

81011

180

135

90270

225

315

81012

180

135

90270

225

315

Cisco Aironet 13.5-dBi Yagi Mast Mount Antenna (AIR-ANT1949)

78-14720-02

Safety Precautions

Each year hundreds of people are killed or injured when attempting to install an antenna. In many of

these cases, the victim was aware of the danger of electrocution, but did not take adequate steps to avoid

the hazard.

For your safety, and to help you achieve a good installation, please read and follow these safety

precautions. They may save your life!

1. If you are installing an antenna for the first time, for your own safety as well as others, seek

professional assistance. Your Cisco sales representative can explain which mounting method to use

for the size and type antenna you are about to install.

2. Select your installation site with safety, as well as performance in mind. Remember: electric power

lines and phone lines look alike. For your safety, assume that any overhead line can kill you.

3. Call your electric power company. Tell them your plans and ask them to come look at your proposed

installation. This is a small inconvenience considering your life is at stake.

4. Plan your installation carefully and completely before you begin. Successful raising of a mast or

tower is largely a matter of coordination. Each person should be assigned to a specific task, and

should know what to do and when to do it. One person should be in charge of the operation to issue

instructions and watch for signs of trouble.

5. When installing your antenna, remember:

a. Do not use a metal ladder.

b. Do not work on a wet or windy day.

c. Do dress properly—shoes with rubber soles and heels, rubber gloves, long sleeved shirt or

jacket.

6. If the assembly starts to drop, get away from it and let it fall. Remember, the antenna, mast, cable,

and metal guy wires are all excellent conductors of electrical current. Even the slightest touch of any

of these parts to a power line complete an electrical path through the antenna and the installer: you!

Warning

IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you

work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar

with standard practices for preventing accidents. Use the statement number provided at the end of

each warning to locate its translation in the translated safety warnings that accompanied this

device.

Statement 1071

SAVE THESE INSTRUCTIONS

Warning

In order to comply with FCC radio frequency (RF) exposure limits, antennas should be located at a

minimum of 7.9 inches (20 cm) or more from the body of all persons.

Statement 332

Cisco Aironet 13.5-dBi Yagi Mast Mount Antenna (AIR-ANT1949)

78-14720-02

Installation Notes

7. If any part of the antenna system should come in contact with a power line, don’t touch it or try to

remove it yourself. Call your local power company. They will remove it safely.

8. If an accident should occur with the power lines call for qualified emergency help immediately.

Installation Notes

General Installation Instructions for Mast-Mounted Antennas

The following instructions are common to most mast-mounted installations.

Step 1 Assemble your new antenna on the ground at the installation site.

Step 2 Attach the antenna to the mast and connect its coaxial cable while you are on the ground.

Step 3 If you lose control of the mast while raising it, make sure that it does not fall in the wrong direction. Use

a durable non-conductive rope secured at each 2-foot level as the mast is raised. Have an assistant tend

the rope, ready to pull the mast clear of any hazards (such as power lines) if it begins to fall.

Step 4 Use the mounting bracket provided with the antenna.

Step 5 If the installation will use guy wires:

a. Install guy anchor bolts.

b. Estimate the length of guy wire and cut it before raising the mast.

c. Attach guy wires to a mast using guy rings.

Step 6 Carefully connect the antenna and mast assembly to its mounting bracket and tighten the clamp bolts.

a. For a guyed installation, you must have at least one assistant to hold the mast upright while you

attach and tighten the guy wires to the anchor bolts.

Step 7 Attach the provided self-adhering DANGER label at eye level on the mast.

Step 8 Install ground rods to remove any static electricity buildup and connect a ground wire to the mast and

ground rod. Use ground rods designed for that purpose, not a spare piece of pipe.

Grounding the Antenna

Follow these guidelines to ground the antenna in accordance with national electrical code instructions.

1. Use No. 10 AWG copper or No. 8 or larger copper-clad steel or bronze wire as ground wires for both

mast and lead-in. Securely clamp the wire to the bottom of the mast.

2. Secure the lead-in wire to an antenna discharge unit and the mast ground wire to the building with

stand-off insulators spaced from 4 ft (1.2 m) to 8 ft (2.4 m) apart.

3. Mount the antenna discharge unit as closely as possible to where the lead-in wire enters the building.

4. Drill a hole in the building’s wall as closely as possible to the equipment to which you will connect

the lead-in cable.

Cisco Aironet 13.5-dBi Yagi Mast Mount Antenna (AIR-ANT1949)

78-14720-02

Installation Notes

Caution There may be wires in the wall. Make sure your drilling location is clear of any any obstructions or other

hazards.

5. Pull the cable through the hole and form a drip loop close to where it enters the building.

6. Thoroughly waterproof the lead-in area.

7. Install a lightning arrestor.

8. Connect the lead-in cable to the equipment.

Choosing a Mounting Location

The antenna is designed to create a directional broadcast pattern. To achieve this pattern, the antenna

should be mounted clear of any obstructions to the sides of the radiating element. If the mounting

location is on the side of a building or tower, the antenna pattern is degraded on the building or tower

side.

Site Selection

Before attempting to install your antenna, determine where you can best place the antenna for safety and

performance.

Follow these steps to determine a safe distance from wires, power lines, and trees.

Step 1 Measure the height of your antenna.

Step 2 Add this length to the length of your tower or mast and then double this total for the minimum

recommended safe distance.

Caution If you are unable to maintain this safe distance, stop and get professional help.

Generally, the higher an antenna is above the ground, the better it performs. Good practice is to install

your antenna about 5 to 10 ft (1.5 to 3 m) above the roof line and away from all power lines and

obstructions. If possible, find a mounting place directly above your wireless device so that the lead-in

cable can be as direct as possible.

Tools and Equipment Required

A mast mounting installation kit is shipped with the antenna. To install the antenna on a mast, you need

the following tools and equipment.

•A 7/16-in. (11.1 mm) wrench

•Cable ties or electrical tape

•Coaxial cable weatherproofing material (such as CoaxSeal)

Cisco Aironet 13.5-dBi Yagi Mast Mount Antenna (AIR-ANT1949)

78-14720-02

Installation Notes

Note The antenna can also be mounted on a wall or other flat vertical surface. Mounting hardware is not

provided.

The following sections contain a typical procedure for installing the antenna on a mast. Your installation

may vary. Before you begin, you may want to refer to Figure 1.

Mounting the Antenna

The antenna is provided with a mast mounting kit that allows you to mount the antenna to masts up to

1 5/8 in. in diameter. Figure 1 shows how the antenna should be mounted to a mast or wall.

Figure 1 Antenna Mounting

Backing

plate

Backing

plate

Direction of

maximum signal

Direction of

maximum signal

Mast mount - side view

Mast mount - top view

Wall mount

Intermediate plate required for

mounting on rough surfaces.

Place flat washers between bolt heads

(or nuts) and mounting base in all

mounting configurations.

81013

Cisco Aironet 13.5-dBi Yagi Mast Mount Antenna (AIR-ANT1949)

78-14720-02

Installation Notes

Follow these instructions to mount the antenna on a mast.

Step 1 Attach the U-bolts, clamps, and backing plate to the antenna as shown in Figure 1.

Step 2 Install a washer and start a locknut on each U-bolt.

Step 3 Position the loose mounting assembly over the mast.

Note To ensure correct antenna polarization orientation, make sure the arrows on the antenna are

pointed up.

Step 4 Use a 7/16-in (11.1-mm) wrench or suitable adjustable wrench to secure the assembly to the mast.

Tighten the locknuts to a point where the antenna does not slide down the mast but is loose enough for

you to rotate.

Step 5 Rotate the antenna until it points towards the other WLAN antenna your wireless device is to

communicate with.

Note The accuracy of the orientation should be within 15 degrees to achieve maximum gain. This is

especially important if the path length is over 1 mile (1.6 kilometers). If you use this antenna to

connect to several terminals, aim it in the general direction of the group. If the paths are not

obstructed or are less than 1 mile (1.6 kilometers), this arrangement should work well.

Step 6 Tighten the locknuts.

Note Tighten the locknuts evenly and do not exceed 45 in-lbs of torque on the locknuts.

Step 7 Secure the antenna cable to the mast with cable ties or electrical tape.

Step 8 Apply the danger label to a plainly visible area of the antenna support structure.

Note The antenna is not DC grounded. It is recommended that you install lightning-protection

devices in your system. See the Installation Instructions for Cisco Aironet Lightning

Arrestors. This document is available on the World Wide Web at the following URL:

http://www.cisco.com/en/US/docs/wireless/lightning_arrestor/installation/guide/hslar.htm

Suggested Cable

Cisco recommends a high-quality, low-loss cable for use with the antenna.

Note The higher the frequency, the greater the loss through the cable. Also, the longer the run,

the greater the loss.

The antenna terminates with a RP-TNC plug after a short, 3-ft (0.91-m) cable. The mating connector to

the antenna is an appropriate RP-TNC jack. The connector on the opposite end will vary according to

the type of equipment used.

Cisco Aironet 13.5-dBi Yagi Mast Mount Antenna (AIR-ANT1949)

78-14720-02

After the cable is attached to the antenna, make sure that the connections are sealed (if outdoors) to

prevent moisture and other weathering elements from affecting performance. Cisco recommends using

a coax seal (such as CoaxSeal) for outdoor connections. Silicon sealant or electrical tape is not

recommended for sealing outdoor connections.

Obtaining Documentation and Submitting a Service Request

For information on obtaining documentation, submitting a service request, and gathering additional

information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and

revised Cisco technical documentation, at:

http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html

Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed

and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free

service and Cisco currently supports RSS Version 2.0.

Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks

can be found at www.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners. The use of the word

partner does not imply a partnership relationship between Cisco and any other company. (1005R)

Inhaltsverzeichnis

Andere Cisco Antenne Handbücher

Cisco

Cisco Catalyst IR1800 Rugged Series Bedienungsanleitung

Cisco

Cisco Aironet AIR-ANT2566D4M-R Bedienungsanleitung

Cisco

Cisco ANT-WPAN-OD-OUT-N Bedienungsanleitung

Cisco

Cisco Aironet AIR-ANT3351 Bedienungsanleitung

Cisco

Cisco 3G-ANTM1916-CM Bedienungsanleitung

Cisco

Cisco Aironet AIR-ANT5145V-R Bedienungsanleitung

Cisco

Cisco Aironet High Gain Omnidirectional Ceiling Mount Antenna... Bedienungsanleitung

Cisco

Cisco Multiband Swivel-Mount Dipole Antenna... Bedienungsanleitung

Cisco

Cisco ANT-4G-PNL-OUT-N Bedienungsanleitung

Cisco

Cisco Aironet AIR-ANT5140V-R Bedienungsanleitung

Cisco

Cisco AIRANT2524DBR Bedienungsanleitung

Cisco

Cisco Multiband Wall-Mount Antenna AIR-ANTM5560P-R Bedienungsanleitung

Cisco

Cisco 4G-ANTM-OM-CM Bedienungsanleitung

Cisco

Cisco AIR-ANT2451NV-R Kurzanleitung

Cisco

Cisco Aironet AIR-ANT2465P-R Bedienungsanleitung

Cisco

Cisco Aironet AIR-ANT2568VG-N Bedienungsanleitung

Cisco

Cisco Aironet 2 dBi Diversity Omnidirectional Ceiling Mount Antenna... Bedienungsanleitung

Cisco

Cisco Aironet AIR-ANT2460P-R Bedienungsanleitung

Cisco

Cisco AIRANT2524DWR Bedienungsanleitung

Cisco

Cisco AIR-ANT2544V4M-R Montageanleitung

Cisco

Cisco Aironet AIR-ANT2513P4M-N Bedienungsanleitung

Cisco

Cisco 4G-LTE-ANTM-O-3 Bedienungsanleitung

Cisco

Cisco 2.4-GHz Swivel-Mount Dipole Antenna... Bedienungsanleitung

Cisco

Cisco Aironet AIR-ANT2465P-R Bedienungsanleitung

Beliebte Antenne Handbücher anderer Marken

Alfa Network

Alfa Network APA-L01 Bedienungsanleitung

Naval

Naval PR-422CA Bedienungsanleitung

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Bedienungsanleitung

TERK Technologies

TERK Technologies TV44 Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Bedienungsanleitung

HP J8999A Bedienungsanleitung

MobilSat

MobilSat MSP-S Bedienungsanleitung

Steren

Steren ANT-UHF 13 Bedienungsanleitung

Novatel

Novatel 600-G Bedienungsanleitung

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Bedienungsanleitung

TRENDnet

TRENDnet TEW-AO12O Bedienungsanleitung

Radio Shack

Radio Shack 15-1837 Bedienungsanleitung

CommScope

CommScope CMAX-OMFX-43M-I53 Bedienungsanleitung

Ramsey Electronics

Ramsey Electronics DAP25 Bedienungsanleitung

COBHAM

COBHAM SAILOR 800 VSAT Gebrauchs- und Pflegehandbuch

Trango Systems

Trango Systems AD900-9 Bedienungsanleitung

Steren

Steren ANT-100 Bedienungsanleitung

IWCS

IWCS iriBelt II Einrichtungshandbuch