Cisco NCS 4000 Series Bedienungsanleitung

Cisco Network Convergence System 4000 Series Unpacking, Moving

and Securing Guide

First Published: 2016-09-30

Last Modified: 2016-11-07

Americas Headquarters

Cisco Systems, Inc.

170 West Tasman Drive

San Jose, CA 95134-1706

USA

http://www.cisco.com

Tel: 408 526-4000

800 553-NETS (6387)

Fax: 408 527-0883

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS,

INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND,

EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH

THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY,

CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB's public domain version

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS" WITH ALL FAULTS.

CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF

MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT

LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS

HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network

topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional

and coincidental.

Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: http://

www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership

relationship between Cisco and any other company. (1110R)

CONTENTS

Preface

Preface v

Audience v

Conventions v

Related Documentation vii

Changes to This Document vii

Obtaining Documentation and Submitting a Service Request vii

CHAPTER 1

Overview 1

Chassis Packaging 1

Verifying the Securing Location 2

Front and Rear Clearances 2

Safety Guidelines 3

Preventing Electrostatic Discharge 4

CHAPTER 2

Unpacking the Chassis 5

Removing the Chassis from the Pallet 9

CHAPTER 3

Moving the Cisco NCS 4016 Chassis 15

Transferring the Chassis to a Mechanical Lifting Device 15

Moving the Cisco NCS 4016 Chassis 20

Moving Guidelines for the Cisco NCS 4016 Chassis 20

Moving the Chassis to the Final Location 21

CHAPTER 4

Securing the Chassis 23

Preparing the Rack for Chassis Installation 23

Preparing to Mount the Chassis in a Rack 26

Cisco Network Convergence System 4000 Series Unpacking, Moving and Securing Guide

iii

Installing the Mounting Brackets 26

Installing the Aid Brackets 31

Removing the Chassis Door 34

Mounting the Chassis into a Rack 38

Attaching the Chassis Door 43

Unpacking Chassis Component Shipping Pallets 43

Cisco Network Convergence System 4000 Series Unpacking, Moving and Securing Guide

Contents

Preface

This guide provides instructions for unpacking the Cisco Network Convergence System (NCS) 4016 chassis

and its components, moving the chassis to its permanent location, and mounting the chassis in a rack.

•Audience, page v

•Conventions, page v

•Related Documentation, page vii

•Changes to This Document, page vii

•Obtaining Documentation and Submitting a Service Request, page vii

Audience

This document is intended for those who unpack the Cisco NCS 4016 chassis and Cisco installation partners

who are responsible for moving and securing the Cisco NCS 4016 chassis. No additional knowledge of routing

or the Cisco IOS XR software is assumed.

Conventions

This document uses the following conventions:

IndicationConvention

Commands and keywords and user-entered text

appear in bold font.

bold font

Document titles, new or emphasized terms, and

arguments for which you supply values are in italic

font.

italic font

Elements in square brackets are optional.[ ]

Required alternative keywords are grouped in braces

and separated by vertical bars.

{x | y | z }

Cisco Network Convergence System 4000 Series Unpacking, Moving and Securing Guide

IndicationConvention

Optional alternative keywords are grouped in brackets

and separated by vertical bars.

[ x | y | z ]

A nonquoted set of characters. Do not use quotation

marks around the string or the string will include the

quotation marks.

string

Terminal sessions and information the system displays

appear in courier font.

courier font

Nonprinting characters such as passwords are in angle

brackets.

< >

Default responses to system prompts are in square

brackets.

[ ]

An exclamation point (!) or a pound sign (#) at the

beginning of a line of code indicates a comment line.

!, #

Means reader take note . Notes contain helpful suggestions or references to material not covered in the

manual.

Note

Means the following information will help you solve a problem . The tips information might not be

troubleshooting or even an action, but could be useful information, similar to a Timesaver.

Tip

Means the described action saves time . You can save time by performing the action described in the

paragraph.

Timesaver

Means reader be careful . In this situation, you might perform an action that could result in equipment

damage or loss of data.

Caution

IMPORTANT SAFETY INSTRUCTIONSThis warning symbol means danger. You are in a situation that

could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with

electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement

number provided at the end of each warning to locate its translation in the translated safety warnings that

accompanied this device.SAVE THESE INSTRUCTIONS

Danger

Cisco Network Convergence System 4000 Series Unpacking, Moving and Securing Guide

Preface

Conventions

Statements using this symbol are provided for additional information and to comply with regulatory and

customer requirements.

Danger

Related Documentation

Cisco Network Convergence System 4000 Series Unpacking, Moving and Securing Guide

viii

Preface

Obtaining Documentation and Submitting a Service Request

CHAPTER 1

Overview

This chapter provides pertinent information that you should know about the Cisco NCS 4016 chassis before

unpacking and moving it into a rack.

The Cisco NCS 4016 chassis contains two slots for route processor (RP) cards, sixteen slots for line cards

(LC), and four slots for fabric cards (FC). The Cisco NCS 4016 chassis is rack mountable. It is compatible

with the following standard rail spacing:

•ANSI 19-inch or 23-inch (2 or 4-post)

•ETSI

For the ANSI 19-inch rack, the minimum front opening must be 17.72 inches (450 mm) to allow for

chassis insertion.

Note

•Chassis Packaging, page 1

•Verifying the Securing Location, page 2

•Safety Guidelines, page 3

Chassis Packaging

The Cisco NCS 4016 chassis arrives on the primary system pallet with a label that describes the contents.

Cards are shipped on a separate card pallet. The complete details on the contents of each pallet reflect the

customer’s sale order, which is reported on the parts identification label on the pallet or shipping manifest.

The primary system pallet contains the chassis, which is covered with a corrugated master shipper packing

crate held together with plastic bands.

The chassis is shipped with the following components already installed:

•Fan trays

•Power trays (AC or DC)

•Power modules

Cisco Network Convergence System 4000 Series Unpacking, Moving and Securing Guide

•External connection unit (ECU)

•Craft panel

•Cosmetic door

The RP, LC, and FC card slots are populated with filler cards.Note

The card pallet contains the route processor cards (RPs), fabric cards (FCs), and line cards (LCs).

The Cisco NCS 4016 chassis is shipped in a double-wall carton on a standard shipping pallet. Always transport

the chassis in its original packaging and make sure that the system is transported and stored in an upright

position. If you plan to store system components before the installation, be sure to store the components

carefully and in their original shipping containers to prevent accidental damage.

Verifying the Securing Location

Before moving the chassis into position, make sure that you have properly prepared the site so that there is

sufficient room for installation and maintenance. Verifying the recommended space ensures that you have

enough space available to perform the initial installation of the chassis and its components.

The floor plan for the Cisco NCS 4016 chassis must include enough space to install the chassis in the equipment

rack and allow sufficient airflow for the system. The floor plan must also provide enough room to access

chassis components for maintenance (for example, to remove fan trays, power modules, cables, and air filters).

For chassis installation, make sure that enough room exists in front of the chassis to accommodate installation

personnel and the lifting device used to hold the chassis in the rack while it is bolted to the rack.

Front and Rear Clearances

The site requires the following front and rear clearances for chassis installation and maintenance access:

•To install the chassis in the equipment rack: approximately 23.6 inches (60 cm)

•To service components and allow system airflow in front of the chassis: 36 inches (91.4 cm)

•To service components and allow system airflow behind the chassis: 24 inches (61 cm)

If the chassis in installed in a cabinet with doors, note the following restrictions:

•The chassis can be placed in a cabinet with the front and rear doors at least 80% open in front of the

inlet and exhaust openings of the chassis.

•The distance between the inlet/exhaust and the door can be as small as 6 inches, but the door should be

facing to an open isle.

•A foot of clearance at front and back should be maintained from the inlet/exhaust and a solid object.

Cisco Network Convergence System 4000 Series Unpacking, Moving and Securing Guide

Overview

Verifying the Securing Location

Andere Handbücher für NCS 4000 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cisco Chassis Handbücher

Cisco

Cisco CRS-1 - Carrier Routing System Router Benutzerhandbuch

Cisco

Cisco NCS 4009 Bedienungsanleitung

Cisco

Cisco cBR Series Bedienungsanleitung

Cisco

Cisco ASR 5000 Bedienungsanleitung

Cisco

Cisco AMP PC3000 Handbuch

Cisco

Cisco 5505 - ASA Firewall Edition Bundle Service-Handbuch

Cisco

Cisco NCS 4000 Series Handbuch

Cisco

Cisco Nexus 7010 Bedienungsanleitung

Cisco

Cisco cBR Bedienungsanleitung

Cisco

Cisco ONS 15454 Bedienungsanleitung

Cisco

Cisco CRS-1 - Carrier Routing System Router Bedienungsanleitung

Cisco

Cisco Network Convergence System 6000 Fabric Card... Handbuch

Cisco

Cisco NCS 6000 Bedienungsanleitung

Cisco

Cisco UCS 5108 Systemhandbuch

Cisco

Cisco ASA5500-HW - Hardware Accessory Kit Network... Handbuch

Cisco

Cisco Nexus 7018 Bedienungsanleitung

Cisco

Cisco NCS 1004 Handbuch

Cisco

Cisco Nexus 7004 Bedienungsanleitung

Cisco

Cisco Firepower 4100/9300 Bedienungsanleitung

Cisco

Cisco UCS C4200 Montage- und Wartungsanleitung

Cisco

Cisco TelePresence Server 7010 Leitfaden

Cisco

Cisco USC 5030 Bedienungsanleitung

Cisco

Cisco NCS 4016 Bedienungsanleitung

Cisco

Cisco ONS 15454 DWDM Betriebsanleitung

Beliebte Chassis Handbücher anderer Marken

Advantech

Advantech IPC-623 Series Bedienungsanleitung

IMC Networks

IMC Networks iMcV/18 Bedienungsanleitung

Lenovo

Lenovo ThinkSystem SR665 V3 Bedienungsanleitung

Wuntronic

Wuntronic PCI4DRQ Bedienungsanleitung

EtherWAN

EtherWAN EMC400 Bedienungsanleitung

Overland Storage

Overland Storage SnapSAN S1000 Leitfaden

Philips

Philips LC4.1E A Bedienungsanleitung

Supermicro

Supermicro SCF418 Series Bedienungsanleitung

Chenbro

Chenbro RM437 Series Bedienungsanleitung

Pickering

Pickering 40-914 Bedienungsanleitung

HP A7503-S Montageanleitung

Supermicro

Supermicro SC823MTQ-R700LPB Bedienungsanleitung

SilverStone

SilverStone RMS08 Series Bedienungsanleitung

NI cRIO-FRC II Bedienungsanleitung

Pickering

Pickering 65-200 Bedienungsanleitung

Allied Telesis

Allied Telesis AT-MMCR18 Bedienungsanleitung

Hisense

Hisense MSD6586 Bedienungsanleitung

JYTEK

JYTEK PXIe-62780 Bedienungsanleitung