Cisco NCS 4016 Bedienungsanleitung

Securing the Chassis

This chapter describes how to secure the Cisco NCS 4016 chassis in the rack.

To install two Cisco NCS 4016 chassis in a single rack, you will need to have a minimum vertical opening

of 48 RU. If you are using the DC Power Front Connection Adapter, only one chassis will fit into the rack.

Note

•Preparing the Rack for Chassis Installation, on page 1

•Preparing to Mount the Chassis in a Rack, on page 3

•Mounting the Chassis into a Rack, on page 17

•Attaching the Chassis Door, on page 22

•Unpacking Chassis Component Shipping Pallets, on page 22

Preparing the Rack for Chassis Installation

Install the Cisco NCS 4016 chassis into one of the following standard racks:

• ANSI 19-inch or 23-inch (2- or 4-post)

• ETSI

For the ANSI 19-inch rack, the minimum front opening must be 17.72 inches (450 mm) to allow for chassis

insertion.

Note

If you are installing a single chassis in a rack, the chassis must go in the middle or bottom portion of the rack

or follow your company chassis mounting practices.

At the bottom of the rack, keep 1 rack unit free to allow for removal of the bottom fan tray.

Note

To bolt the rack to the floor, a floor bolt kit (also called an anchor embedment kit ) is required. For information

on bolting the rack to the floor, consult a company that specializes in floor mounting kits (such as Hilti; see

Hilti.com for details). Make sure that floor mounting bolts are accessible, especially if annual re-torquing of

bolts is required.

Securing the Chassis

Figure 1: Single Cisco NCS 4016 Chassis Mounted in Rack

Before you move the chassis or mount the chassis into the rack, we recommend that you do the following:

SUMMARY STEPS

1. Place the rack where you plan to install the Cisco NCS 4016 chassis.

2. Secure the rack to the floor.

Securing the Chassis

Preparing the Rack for Chassis Installation

DETAILED STEPS

Step 1 Place the rack where you plan to install the Cisco NCS 4016 chassis.

Step 2 Secure the rack to the floor.

The chassis should be mounted on a rack that is permanently affixed to the building. Statement 1049

Warning

Preparing to Mount the Chassis in a Rack

Before you mount the Cisco NCS 4016 chassis into a rack, it is critical that the installation site be prepared

properly to handle the chassis weight, power requirements, cooling needs, and other requirements.

Because a fully-configured chassis weight can be up to 412 lb (187 kg), you should review the rack

specifications from the manufacturer to determine whether the racks you have are appropriate to handle the

weight of the chassis. For specifications on the chassis, see the Cisco Network Convergence System 4000

Series Hardware Installation Guide .

To avoid tipping the chassis and possible injury when installing it, take care to properly position the chassis

in the rack when you are mounting it.

Caution

Before mounting the chassis in the rack, perform the following steps:

Installing the Mounting Brackets

This section explains how to install the top and bottom mounting brackets for the specific type of rack you

are using.

• For 2-post ANSI racks, the brackets are installed in the middle position.

• For 4-post ANSI racks and ETSI cabinets, the brackets are installed in the front position.

Securing the Chassis

Preparing to Mount the Chassis in a Rack

Figure 2: Positioning for Mounting Bracket Installation

Top bracket area, front position2Top bracket area, middle position1

Bottom bracket area, front position4Bottom bracket area, middle position3

Prerequisites

Make sure that you have the correct type of mounting brackets to suit your rack type. There are three different

types of mounting brackets for the three types of racks (ANSI 19-inch or 23-inch or ETSI).

Securing the Chassis

Installing the Mounting Brackets

Required Tools and Equipment

• Number 1 Phillips screwdriver

• Cisco NCS 4016 installation kit (NCS4K-INST-KIT=)

Installing the Mounting Brackets

To attach the mounting brackets, simply fix each bracket onto the chassis using six screws as shown in the

figure, below.

Figure 3: Attaching Chassis Mounting Brackets

Various types of bracket installation are shown in these illustrations:

Securing the Chassis

Installing the Mounting Brackets

Figure 4: Attaching ANSI 19-Inch Brackets to Front (4-Post Rack) or Middle (2-Post Rack)

Securing the Chassis

Installing the Mounting Brackets

Figure 5: Attaching ANSI 23-Inch Brackets to Front (4-Post Rack) or Middle (2-Post Rack)

Securing the Chassis

Installing the Mounting Brackets

Figure 6: Attaching ETSI Brackets to Front

Installing the Aid Brackets

This section explains how to install the aid brackets onto the rack. The aid brackets hold the weight of the

chassis while you secure it in the rack.

Prerequisites

Identify the position of the chassis inside the rack to define the aid brackets position.

Required Tools and Equipment

• Number 1 Phillips screwdriver

• Cisco NCS 4016 installation kit (NCS4K-INST-KIT=)

Steps

SUMMARY STEPS

1. Attach the aid brackets to the rack below where the chassis will sit. Tighten the two screws to firmly attach

the brackets to the rack.

2. Once the chassis has been installed, remove the aid brackets. Loosen the two screws from the aid brackets

and take off the rack.

DETAILED STEPS

Step 1 Attach the aid brackets to the rack below where the chassis will sit. Tighten the two screws to firmly attach the brackets

to the rack.

Securing the Chassis

Installing the Aid Brackets

Figure 7: Attaching Aid Brackets to the Rack

Step 2 Once the chassis has been installed, remove the aid brackets. Loosen the two screws from the aid brackets and take off

the rack.

Keep the aid brackets in case of future chassis relocation.

Tip

Securing the Chassis

Installing the Aid Brackets

What to do next

To accommodate equipment racks with different mounting hole patterns, the aid brackets have groups of

screw holes on either side.

The mounting holes in the aid brackets are spaced so that one mounting hole in each hole group aligns with

a corresponding hole in the equipment rack. By using the corresponding mounting hole (in the same hole

group) on the opposite side of the rack, you can keep both the aid brackets leveled.

When you are installing the chassis in a rack, leave the filler cards in place to provide the chassis with enough

support to keep it square during the procedure.

Caution

Because of the chassis size and weight, it is unsafe to lift the chassis without mechanical assistance.

Caution

Removing the Chassis Door

Before installing the chassis in a rack, remove the front door of the chassis to ensure that the door is not

damaged in any way.

Required Tools and Equipment

• ESD-preventive wrist strap

• Number 2 Phillips screwdriver, medium and small slot-head screwdrivers

Steps

SUMMARY STEPS

1. Turn the knob to unlock the door.

2. Open the door.

3. Loosen the screw to disconnect the ground cable.

4. Move down the pin to release the door from the chassis hinge.

5. Move up the door to release the bottom hinge pin.

DETAILED STEPS

Step 1 Turn the knob to unlock the door.

Securing the Chassis

Removing the Chassis Door

Andere Handbücher für NCS 4016

Inhaltsverzeichnis

Andere Cisco Chassis Handbücher

Cisco

Cisco NCS 4009 Bedienungsanleitung

Cisco

Cisco ONS 15454 DWDM Betriebsanleitung

Cisco

Cisco Firepower 4100/9300 Bedienungsanleitung

Cisco

Cisco NCS 4000 Series Handbuch

Cisco

Cisco CRS-1 - Carrier Routing System Router Benutzerhandbuch

Cisco

Cisco cBR Bedienungsanleitung

Cisco

Cisco 7513 Series Leitfaden

Cisco

Cisco Nexus 7010 Bedienungsanleitung

Cisco

Cisco Network Convergence System 6000 Fabric Card... Handbuch

Cisco

Cisco 5505 - ASA Firewall Edition Bundle Service-Handbuch

Cisco

Cisco ONS 15454 Bedienungsanleitung

Cisco

Cisco Firepower 4100 Series Bedienungsanleitung

Cisco

Cisco NCS 1010 Bedienungsanleitung

Cisco

Cisco USC 5030 Bedienungsanleitung

Cisco

Cisco Nexus 9504 Bedienungsanleitung

Cisco

Cisco Remote PHY Shelf 7200 Bedienungsanleitung

Cisco

Cisco C4200 Bedienungsanleitung

Cisco

Cisco 6160 Gebrauchs- und Pflegehandbuch

Cisco

Cisco Nexus 3000 series Bedienungsanleitung

Cisco

Cisco CRS-1 - Carrier Routing System Router Technisches Handbuch

Cisco

Cisco SCE8000 GBE Bedienungsanleitung

Cisco

Cisco UCS 5108 Systemhandbuch

Cisco

Cisco NCS 4000 Series Bedienungsanleitung

Cisco

Cisco AS5350 - Universal Access Server Bedienungsanleitung

Beliebte Chassis Handbücher anderer Marken

Advantech

Advantech IPC-623 Series Bedienungsanleitung

IMC Networks

IMC Networks iMcV/18 Bedienungsanleitung

Chenbro

Chenbro RB13804N4WFT Bedienungsanleitung

Lenovo

Lenovo ThinkSystem SR665 V3 Bedienungsanleitung

Wuntronic

Wuntronic PCI4DRQ Bedienungsanleitung

EtherWAN

EtherWAN EMC400 Bedienungsanleitung

Overland Storage

Overland Storage SnapSAN S1000 Leitfaden

Philips

Philips LC4.1E A Bedienungsanleitung

Supermicro

Supermicro SCF418 Series Bedienungsanleitung

Chenbro

Chenbro RM437 Series Bedienungsanleitung

Pickering

Pickering 40-914 Bedienungsanleitung

HP A7503-S Montageanleitung

Supermicro

Supermicro SC823MTQ-R700LPB Bedienungsanleitung

SilverStone

SilverStone RMS08 Series Bedienungsanleitung

NI cRIO-FRC II Bedienungsanleitung

Pickering

Pickering 65-200 Bedienungsanleitung

Allied Telesis

Allied Telesis AT-MMCR18 Bedienungsanleitung

Hisense

Hisense MSD6586 Bedienungsanleitung