Cisco Nexus 3000 series Bedienungsanleitung
Installing the Switch Chassis
•Safety, on page 1
•Installation Guidelines, on page 2
•Unpacking and Inspecting the Switch, on page 2
•Attaching L-Brackets to the Chassis, on page 3
•Attaching Magnet to the Chassis, on page 4
•Grounding the Chassis, on page 5
•Starting the Switch, on page 6
Safety
Before you install, operate, or service the switch, see the Regulatory, Compliance, and Safety Information for
the Cisco Nexus 3000 and 9000 Series for important Safety Information.
Statement 1071—Warning Definition
IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work
on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard
practices for preventing accidents. Use the statement number provided at the end of each warning to locate
its translation in the translated safety warnings that accompanied this device.
SAVE THESE INSTRUCTIONS
Warning
Statement 1017—Restricted Area
This unit is intended for installation in restricted access areas. A restricted access area can be accessed by
skilled, instructed or qualified personnel.
Warning
Installing the Switch Chassis
1
Statement 1030—Equipment Installation
Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Warning
Installation Guidelines
When installing the switch, follow these guidelines:
• Ensure that there is adequate clearance space around the switch to allow for servicing the switch and for
adequate airflow.
• Ensure that the chassis can be adequately grounded. If the switch is not mounted in a grounded rack, we
recommend connecting the system ground on the chassis directly to an earth ground.
• Ensure that the site power meets the power requirements for the switch. If available, you can use an
uninterruptible power supply (UPS) to protect against power failures.
Avoid UPS types that use ferroresonant technology. These UPS types can become
unstable with the switch, which can have substantial current draw fluctuations
because of fluctuating data traffic patterns.
Caution
• Ensure that circuits are sized according to local and national codes. Typically, this often requires one or
both of the following:
• AC power supplies typically require at least a 15-A or 20-A AC circuit, 100 to 240 VAC, and a
frequency of 50 to 60 Hz.
To prevent loss of input power, ensure the total maximum loads on the circuits
supplying power to the switch are within the current ratings for the wiring and
breakers.
Caution
Statement 1005—Circuit Breaker
This product relies on the building's installation for short-circuit (overcurrent)
protection. Ensure that the protective devices is rated not greater than 20A (North
America), 16A (Europe), and 13A (UK).
Warning
Unpacking and Inspecting the Switch
Before you install the switch, be sure to unpack and inspect the switch for damage or missing components.
If anything is missing or damaged, contact your customer service representative immediately.
Installing the Switch Chassis
2
Installing the Switch Chassis
Installation Guidelines
Keep the shipping container in case the chassis requires shipping at a later time.
Tip
Before you begin
Before you unpack the switch and before you handle any switch components, be sure that you are wearing a
grounded electrostatic discharge (ESD) strap. To ground the strap, attach it directly to an earth ground or to
a grounded rack or grounded chassis (there must be a metal-to-metal connection to the earth ground).
Check for damage and report any discrepancies or damage to your customer service representative. Have the following
information ready:
• Invoice number of shipper (see packing slip)
• Model and serial number of the damaged unit
• Description of damage
• Effect of damage on the installation
Attaching L-Brackets to the Chassis
You attach two L-brackets to each side of the chassis. These brackets hold the chassis in place on a flat surface.
Before you begin
• You must have the following tools and equipment:
• Phillips-head screwdriver
• L-brackets (4) and screws (4)
Step 1 Align the hole in the L-bracket with the hole on the side of the chassis. Attach the L-bracket with a screw using a
Phillips-head screwdriver. See the following figure.
Installing the Switch Chassis
3
Installing the Switch Chassis
Attaching L-Brackets to the Chassis
Screw (4)2L-bracket (4)1
Step 2 Use screws to attach the brackets to a flat surface.
Attaching Magnet to the Chassis
You attach the magnet to the bottom of the chassis. The magnet holds the chassis in place on a flat surface.
Before you begin
• You must have the following equipment:
• Chassis magnet
Step 1 Align the magnet to the bottom of the chassis. Attach the magnet to the chassis. See the following figure.
Installing the Switch Chassis
4
Installing the Switch Chassis
Attaching Magnet to the Chassis
Magnet1
Step 2 Use the magnet on the bottom of the chassis to attach the chassis to a flat surface.
Grounding the Chassis
The switch chassis is automatically grounded when you properly install the switch in a grounded rack with
metal-to-metal connections between the switch and rack.
You can also ground the chassis, which is required if the rack is not grounded, by attaching a customer-supplied
grounding cable. Attach the cable to the chassis grounding pad and the facility ground.
Statement 1024—Ground Conductor
This equipment must be grounded. To reduce the risk of electric shock, never defeat the ground conductor or
operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical
inspection authority or an electrician if you are uncertain that suitable grounding is available.
Warning
Statement 1046—Installing or Replacing the Unit
To reduce risk of electric shock, when installing or replacing the unit, the ground connection must always be
made first and disconnected last.
Warning
Before you begin
Before you can ground the chassis, you must have a connection to the earth ground for the data center building.
Step 1 Use a wire-stripping tool to remove approximately 0.75 inch (19 mm) of the covering from the end of the grounding
wire. We recommend 6-AWG wire for the U.S. installations.
Step 2 Insert the stripped end of the grounding wire into the open end of the grounding lug. Use a crimping tool to crimp the
lug to the wire, see the following figure. Verify that the ground wire is securely attached to the grounding lug by attempting
to pull the wire out of the crimped lug.
Installing the Switch Chassis
5
Installing the Switch Chassis
Grounding the Chassis
2 M4 screws are used to
secure the grounding lug to
the chassis
3Chassis grounding pad1
Grounding cable, with 0.75
in. (19 mm) of insulation that
is stripped from one end,
which is inserted into the
grounding lug and crimped
in place
2
Step 3 Secure the grounding lug to the chassis grounding pad with two M4 screws, see the previous figure. Tighten the screws
to 11 to 15 in-lb (1.24 to 1.69 N·m) of torque.
Step 4 Prepare the other end of the grounding wire and connect it to the facility ground.
Starting the Switch
You start the switch by connecting it to its dedicated power source. If you need n+1 redundancy, you must
connect each of the power supplies to one or two power sources. If you need n+nredundancy, you must
connect each power supply in a switch to a different power source.
Before you begin
• The switch must be installed and secured to a rack or cabinet.
• The switch must be adequately grounded.
• The rack must be close enough to the dedicated power source so that you can connect the switch to the
power source by using a designated power cables.
• You have the designated power cables for the power supplies that you are connecting to the dedicated
power sources.
Depending on the outlet receptacle on your AC power distribution unit, you might
need an optional jumper power cord to connect the switch to your outlet receptacle.
Note
• The switch is not connected to the network (this includes any management or interface connections).
Step 1 For the AC power supply, do the following:
a) Using the recommended AC power cable for your country or region, connect one end to the AC power supply.
b) Connect the other end of the power cable to the AC power source.
Step 2 Listen for the fans; they should begin operating when the power supply is powered.
Step 3 After initialization, the switch chassis Status (STS) LED is green.
Step 4 Verify that the system software has booted and the switch has initialized without error messages.
Installing the Switch Chassis
6
Installing the Switch Chassis
Starting the Switch
Note
A setup utility automatically launches the first time that you access the switch and guides you through the basic
configuration. For instructions on how to configure the switch and check module connectivity, see the appropriate Cisco
Nexus 9000 configuration guide.
Installing the Switch Chassis
7
Installing the Switch Chassis
Starting the Switch
Installing the Switch Chassis
8
Installing the Switch Chassis
Starting the Switch
Andere Handbücher für Nexus 3000 series
10
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Cisco Chassis Handbücher
Cisco
Cisco CRS-1 - Carrier Routing System Router Benutzerhandbuch
Cisco
Cisco 6160 Gebrauchs- und Pflegehandbuch
Cisco
Cisco Firepower 4100/9300 Bedienungsanleitung
Cisco
Cisco USC 5030 Bedienungsanleitung
Cisco
Cisco Nexus 9504 Bedienungsanleitung
Cisco
Cisco Remote PHY Shelf 7200 Bedienungsanleitung
Cisco
Cisco SRS Series Bedienungsanleitung
Cisco
Cisco ONS 15454 DWDM Betriebsanleitung
Cisco
Cisco NCS 4016 Bedienungsanleitung
Cisco
Cisco NCS 4000 Series Bedienungsanleitung
Cisco
Cisco ASR 5500 Installationsanleitung
Cisco
Cisco AMP PC3000 Handbuch
Cisco
Cisco ASR 5000 Bedienungsanleitung
Cisco
Cisco C4200 Bedienungsanleitung
Cisco
Cisco CRS-1 - Carrier Routing System Router Technisches Handbuch
Cisco
Cisco UCS M4308 Leitfaden
Cisco
Cisco UCS C4200 Montage- und Wartungsanleitung
Cisco
Cisco ASA5500-HW - Hardware Accessory Kit Network... Handbuch
Cisco
Cisco UCS 5108 Bedienungsanleitung
Cisco
Cisco NCS 1004 Handbuch
