Cisco 8832 Bedienungsanleitung

Your Phone

•Your Cisco IP Conference Phone 8832 and 8832NR, on page 1

•New and Changed Information, on page 2

•Phone Setup, on page 4

•Self Care Portal, on page 14

•Cisco IP Conference Phone 8832 Buttons and Hardware, on page 16

•Phone Firmware and Upgrades, on page 21

•Energy Savings, on page 22

•Additional Help and Information , on page 23

Your Cisco IP Conference Phone 8832 and 8832NR

The Cisco IP Conference Phone 8832 and 8832NR provide high-definition (HD) audio performance and

360-degree coverage for medium to large conference rooms and executive offices. The conference phone has

sensitive microphones that let you speak in a normal voice and be clearly heard from up to 10 feet (2.1 m)

away.

Figure 1: Cisco IP Conference Phone 8832

Your Phone

You can connect two wired expansion microphones to the phone to increase coverage in larger conference

rooms.

The phone also supports an optional set of two wireless expansion microphones.

The Cisco IP Conference Phone 8832NR (non-radio) version does not support Wi-Fi or wireless expansion

microphones.

The phone can be used for a 20 x 20 foot (6.1 x 6.1 m) room and up to 10 people. When you add the expansion

microphones, coverage extends to a 20 x 34 foot (6.1 x 10 m) room and up to 22 people.

You can connect two base units to increase the coverage for a room. This configuration requires the optional

Daisy Chain kit and can support two expansion microphones (either wired or wireless, but not a mixed

combination). If you are using wired microphones with the Daisy Chain kit, the configuration provides coverage

for a room up to 20 x 50 feet (6.1 x 15.2 m) and up to 38 people. If you are using wireless microphones with

the Daisy Chain kit, the configuration provides coverage for a room up to 20 x 57 feet (6.1 x 17.4 m) and up

to 42 people.

Feature Support

This document describes all the features that the device supports. However, not all features may be supported

with your current configuration. For information on supported features, contact your administrator.

New and Changed Information

You can use the information in the following sections to understand what has changed in the document. Each

section contains the major changes.

New and Changed Information for Firmware Release 12.8(1)

Table 1: New and Changed Information for Firmware Release 12.8(1)

New or Changed ContentFeature

Replace Your Existing Phone with a New Phone, on

page 13

Phone Data Migration

New and Changed for Firmware Release 12.7(1)

The following table shows the changes made for Firmware Release 12.7(1).

Table 2: Cisco IP Conference Phone 8832 User Guide Revisions for Firmware Release 12.7(1)

Updated SectionRevision

Answer a Call Within Your Hunt GroupUpdated for hunt group calls on Call Alert

Your Phone

Feature Support

Updated SectionRevision

In certain circumstances, users who dialed a number

that was busy received the reorder tone. With this

release, the user hears the busy tone.

New sections Conference Phone Navigation, on page

18,Conference Phone Softkeys, on page 18,Phone

Icons, on page 18, and Clean the Phone Screen, on

page 19.

General changes

New and Changed Information for Firmware Release 12.6(1)

No user guide updates were required for Firmware Release 12.6(1).

New and Changed Information for Firmware Release 12.5(1)SR3

The following table shows the changes that were made for Firmware Release 12.5(1)SR3.

Table 3: Cisco IP Conference Phone 8832 User Guide Revisions for Firmware Release 12.5(1)SR3

New or Updated SectionRevision

Phone Keypad Characters, on page 19New topic

New and Changed Information for Firmware Release 12.5(1)SR2

No User Guide updates were required for Firmware Release 12.5(1)SR2.

Firmware Release 12.5(1)SR2 replaces Firmware Release 12.5(1) and Firmware 12.5(1)SR1. Firmware

Release 12.5(1) and Firmware Release 12.5(1)SR1 have been deferred in favor of Firmware Release 12.5(1)SR2.

New and Changed Information for Firmware Release 12.5(1)SR1

No updates were required for Firmware Release 12.5(1)SR1.

New and Changed Information for Firmware Release 12.5(1)

No updates were required for Firmware Release 12.5(1).

New and Changed Information for Firmware Release 12.1(1)

The following table shows the changes that were made for Firmware Release 12.1(1).

Your Phone

New and Changed Information for Firmware Release 12.6(1)

Table 4: Cisco IP Conference Phone 8832 User Guide Revisions for Firmware Release 12.1(1)

New or Updated SectionRevision

Connect to the Network, on page 4Updates to support for Cisco IP Conference

Phone 8832 PoE Injector

•Your Cisco IP Conference Phone 8832 and 8832NR, on

page 1

•Wireless Expansion Microphone, on page 20

•Install the Wireless Expansion Microphones, on page 9

•Pair a Wireless Microphone, on page 9

•Unpair a Wireless Microphone, on page 10

•Install the Wireless Microphone Charging Cradle, on page

•Charge a Wireless Microphone, on page 11

Support for Wireless Microphone

•Your Cisco IP Conference Phone 8832 and 8832NR, on

page 1

•Daisy Chain Mode, on page 11

Support for Daisy Chain

Connect to the Network, on page 4Support for Cisco IP Conference Phone

8832 Non-PoE Ethernet Injector

•Connect to the Network, on page 4

•Set Up Wi-Fi Client, on page 6

•Connect to a Preconfigured Wi-Fi Network, on page 7

Support for Wi-Fi

•Connect to the Network, on page 4

•Connect to Expressway, on page 7

Support for Mobile and Remote Access

Through Expressway

Calls That Require a Billing Code or Authorization CodeSupport for CMC and FAC

Phone Setup

Your administrator sets up your phone and connects it to the network. If your phone is not set up and connected,

contact your administrator for instructions.

Connect to the Network

You need to connect the phone to the network.

• Wired network connection—All wired network connections use one of the following:

Your Phone

Phone Setup

•PoE deployment: Connect the phone to the Cisco IP Conference Phone 8832 PoE Injector and

connect the injector to the network with an Ethernet cable.

•Non-PoE deployment: Depending on your location, use one of the following options:

• Connect the phone to the Cisco IP Conference Phone 8832 Non-PoE Ethernet Injector.

Then, connect the injector to the network with an Ethernet cable and to an electric outlet with

a power adapter.

• Connect the phone to the Cisco IP Conference Phone 8832 Ethernet Injector. Then, connect

the injector to the network with an Ethernet cable and to an electric outlet with a power adapter.

You can use this option only if you are based in North America.

• Wireless connection—The Cisco IP Conference Phone 8832 can connect to a Wireless Access Point

using Wi-Fi.

Mobile and Remote Access Through Expressway—If your administrator sets up Mobile and Remote Access

Through Expressway and you connect your phone to the network, it connects to the Expressway server.

Figure 2: PoE Deployment Options

The following figure shows the two PoE deployment options. You can use the option that is shown in the

right-side illustration only if you are based in North America.

Cisco IP Conference Phone 8832 Ethernet Injector with

the PoE power option

Cisco IP Conference Phone 8832 PoE Injector

with the PoE power option

Figure 3: Non-PoE Deployment Options

The following figure shows the two Non-PoE deployment options. You can use the option that is shown in

the right side illustration only if you are based in North America.

Your Phone

Connect to the Network

Cisco IP Conference Phone 8832 Ethernet Injector with

the Ethernet power option

Cisco IP Conference Phone 8832 Non-PoE

Ethernet Injector with the Ethernet power option

Figure 4: Wi-Fi Network Connection

Set Up Wi-Fi Client

The Cisco IP Conference Phone 8832 can access a Wi-Fi network. You need a power adapter to power the

phone. The Cisco IP Conference Phone 8832NR cannot be used with a Wi-Fi network.

Before you begin

Your administrator needs to configure settings on the call control system to enable Wi-Fi access.

Procedure

Step 1 If the phone is plugged into the Ethernet, unplug the Ethernet cable.

Step 2 Press Settings.

Step 3 Navigate to Admin settings >Network setup >Wi-Fi client setup.

Your Phone

Set Up Wi-Fi Client

Step 4 Navigate to Wireless and press On.

Step 5 Press Apply to save the changes, or press Revert to cancel the changes.

Step 6 Navigate to Network name.

Step 7 When the phone finishes scanning the SSID, choose a network to join.

Step 8 Enter your Wi-Fi credentials and press Connect.

Connect to a Preconfigured Wi-Fi Network

You can connect your Cisco IP Conference Phone 8832 to the network using Wi-Fi, but, for security, enter

your username and password. But, the Cisco IP Conference Phone 8832NR does not support Wi-Fi.

Depending upon how your phone is configured, you could be required to sign in when you join a Wi-Fi

network or when your phone powers up.

You cannot dismiss the Wi-Fi sign-in window without entering the correct username and password.

Procedure

Step 1 Enter your Wi-Fi credentials when prompted.

Step 2 Select Sign-in.

Connect with Activation Code Onboarding

If your network has been configured to support this feature, then you can use Activation Code Onboarding

to connect to your company's phone network.

Enter an Activation Code

Activation codes are used to set up your new phone. They can only be used once, and expire after 1 week.

Contact your administrator if you don't know your code or if you need a new one.

Procedure

Step 1 Enter your activation code on the activation screen.

Step 2 Press Submit.

Connect to Expressway

You can use Mobile and Remote Access Through Expressway to connect to your corporate network when

you are working away from your office.

Your Phone

Connect to a Preconfigured Wi-Fi Network

Procedure

Step 1 Reset service mode through Settings >Admin Settings >Reset Settings >Service mode.

Step 2 Press Select when prompted to change the service mode.

Step 3 Enter the service domain and press Continue.

Step 4 Enter your username and password.

Step 5 Select Sign in.

Install the Wired Expansion Microphones

The phone supports an optional kit with two wired expansion microphones. You can extend the microphones

up to 7 feet (2.13m) from the phone. For best results, we recommend that you place the microphones at least

3 feet (0.91m) away from the phone.

Procedure

Step 1 Plug the end of the microphone cable into the port on the side of the phone.

Step 2 Extend the microphone cable to the desired position.

The following figure shows installation of a wired expansion microphone.

Figure 5: Wired Expansion Microphone Installation

Related Topics

Wired Expansion Microphone, on page 20

Your Phone

Install the Wired Expansion Microphones

Install the Wireless Expansion Microphones

The conference phone provides the option of connecting two wireless expansion microphones.

You must use either two wired microphones or two wireless microphones with the phone, but not a mixed

combination.

Note

When the phone is in a call, the LED on the expansion microphone is lit green. To mute the expansion

microphone, press the Mute key. When the microphone is muted, the LED is lit red. When the battery in the

microphone is low, the battery indication LED blinks rapidly.

Before you begin

Disconnect the wired expansion microphones before you install wireless expansion microphones. You cannot

use both wired and wireless expansion microphones at the same time.

Procedure

Step 1 Position the table mount plate on the table surface location where you want to place the microphone.

Step 2 Remove the adhesive for the double-stick tape on the bottom of the table mount plate. Place the table mount

plate to adhere to the table surface.

Step 3 Attach the microphone to the table mount plate. Magnets are embedded in the microphone to snap the unit

into place.

You can move the microphone and attached table mount to a different location on the table surface as needed.

Use care when moving to protect the unit.

Related Topics

Wireless Expansion Microphone, on page 20

Install the Wireless Expansion Microphones, on page 9

Pair a Wireless Microphone

Before you begin

Unplug any wired microphones.

Procedure

Step 1 Press Settings.

Step 2 Select Admin Settings >Microphones >Wireless microphones.

Step 3 Select either Microphone 1 or Microphone 2 and press Pair.

If a microphone is already linked to a particular channel, the phone screen shows that the microphone is paired.

Your Phone

Install the Wireless Expansion Microphones

Step 4 Press Mute on the wireless microphone until the microphone LED blinks white.

If the pairing succeeds, the phone screen displays a success message.

Step 5 (Optional) Press Cancel to revert to the Wireless microphones menu.

Related Topics

Wireless Expansion Microphone, on page 20

Unpair a Wireless Microphone

Procedure

Step 1 Press Settings.

Step 2 Select Admin Settings >Microphones >Wireless microphones.

Step 3 Select either Microphone 1 or Microphone 2.

If the selected channel is paired, the Unpair softkey displays on the phone screen.

Step 4 Press Unpair.

Related Topics

Wireless Expansion Microphone, on page 20

Install the Wireless Microphone Charging Cradle

You use the charging cradle to charge the wireless microphone battery.

Procedure

Step 1 Plug the charging cradle power adapter into an electrical outlet.

Step 2 Plug one end of the USB-C cable to the charging cradle and the other end into the power adapter.

The following figure shows installation of a wireless microphone charging cradle.

Your Phone

Unpair a Wireless Microphone

Andere Handbücher für 8832

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cisco Konferenztelefon Handbücher

Cisco

Cisco TANDBERG?150MXP Bedienungsanleitung

Cisco

Cisco Unified IP Conference Phone 8831 Bedienungsanleitung

Cisco

Cisco Webex Room Kit Bedienungsanleitung

Cisco

Cisco 7832 Bedienungsanleitung

Cisco

Cisco 7832 Bedienungsanleitung

Cisco

Cisco Unified IP Conference Phone 8831NR Bedienungsanleitung

Cisco

Cisco 8832 Bedienungsanleitung

Cisco

Cisco Webex Room Kit Bedienungsanleitung

Cisco

Cisco Conference Phone Bedienungsanleitung

Cisco

Cisco 8832 Gebrauchsanweisung

Cisco

Cisco CP-8832 Bedienungsanleitung

Cisco

Cisco 7832 Bedienungsanleitung

Cisco

Cisco IP Conference Phone 7832 Bedienungsanleitung

Cisco

Cisco EX60 Bedienungsanleitung

Cisco

Cisco 8832 Bedienungsanleitung

Cisco

Cisco 7832 Betriebsanleitung

Cisco

Cisco 7832 Bedienungsanleitung

Cisco

Cisco MPP 8832 Handbuch

Cisco

Cisco 8832 Bedienungsanleitung

Cisco

Cisco 8832 Bedienungsanleitung

Cisco

Cisco 7832 Bedienungsanleitung

Cisco

Cisco 8832 Bedienungsanleitung

Cisco

Cisco 8831 Bedienungsanleitung

Cisco

Cisco 8800 Series Bedienungsanleitung

Beliebte Konferenztelefon Handbücher anderer Marken

Polycom

Polycom SoundStation 2W Service-Handbuch

Vixtel

Vixtel glass 1100 Bedienungsanleitung

Oregon Scientific

Oregon Scientific OS200 Bedienungsanleitung

Polycom

Polycom SoundStation IP 4000 Bedienungsanleitung

AbleNet

AbleNet Prism C Bedienungsanleitung

Albrecht

Albrecht Multicom Bedienungsanleitung

Fortinet

Fortinet FortiFone FON-C70 Bedienungsanleitung

Avaya

Avaya B159 Series Bedienungsanleitung

Konftel

Konftel Konftel 55W Bedienungsanleitung

Mitel

Mitel 6867i Premium Bedienungsanleitung

Polycom

Polycom SoundStation 2W Service-Handbuch

Yealink

Yealink CP920 Bedienungsanleitung

Polycom

Polycom SoundStation IP 6000 Bedienungsanleitung

Mitel

Mitel 6970 IP Bedienungsanleitung

Yealink

Yealink CPE860 Fehlerbehebungshandbuch

Konftel

Konftel 60W Bedienungsanleitung

Mitel

Mitel UC360 Bedienungsanleitung

Cortelco

Cortelco CP4400 Series Einrichtungshandbuch