Cisco 2100 Series Bedienungsanleitung

721-1001-000 Rev AH

December 2016

VIEW Certified Configuration Guide

Cisco Systems Inc.

2100/2500/4400/5500/7500/8500 Series WLC (Wireless LAN Controller),

WiSM (Wireless Services Module), WiSM2, WLC Module, WLC SW for SRE, 3750G

Integrated WLC, and Virtual Controller

with 60x, 104x, 113x, 114x, 1121, 122x, 123x, 124x, 125x, 126x, 13xx, 152x, 155x,

160x, 170x, 260x, 270x, 350x, 360x, 370x APs

Spectralink VIEW Certified Configuration Guide: Cisco Controllers and APs

721-1001-000-AH.docx

December 2016 2

names and marks associated with Spectralink’s products are trademarks and/or service marks of

Spectralink Corporation and are common law marks in the United States and various other countries. All

other trademarks are property of their respective owners. No portion hereof may be reproduced or

transmitted in any form or by any means, for any purpose other than the recipient’s personal use, without

the express written permission of Spectralink.

manual, or the software described herein, may be reproduced or transmitted in any form or by any

means, or translated into another language or format, in whole or in part, without the express written

permission of Spectralink Corporation.

Do not remove (or allow any third party to remove) any product identification, copyright or other notices.

Notice

Spectralink Corporation has prepared this document for use by Spectralink personnel and customers.

The drawings and specifications contained herein are the property of Spectralink and shall be neither

reproduced in whole or in part without the prior written approval of Spectralink, nor be implied to grant any

license to make, use, or sell equipment manufactured in accordance herewith.

Spectralink reserves the right to make changes in specifications and other information contained in this

document without prior notice, and the reader should in all cases consult Spectralink to determine

whether any such changes have been made.

NO REPRESENTATION OR OTHER AFFIRMATION OF FACT CONTAINED IN THIS DOCUMENT

INCLUDING BUT NOT LIMITED TO STATEMENTS REGARDING CAPACITY, RESPONSE-TIME

PERFORMANCE, SUITABILITY FOR USE, OR PERFORMANCE OF PRODUCTS DESCRIBED

HEREIN SHALL BE DEEMED TO BE A WARRANTY BY SPECTRALINK FOR ANY PURPOSE, OR

GIVE RISE TO ANY LIABILITY OF SPECTRALINK WHATSOEVER.

Contact Information

US Location Denmark Location UK Location

+1 800-775-5330 +45 7560 2850 +44 (0) 20 3284 1536

Spectralink Corporation Spectralink Europe ApS Spectralink Europe UK

2560 55th Street Bygholm Soepark 21 E Stuen 329 Bracknell, Doncastle Road

Boulder, CO 80301 8700 Horsens Bracknell, Berkshire, RG12 8PE

USA Denmark United Kingdom

info@spectralink.com infoemea@spectralink.com infoemea@spectralink.com

Spectralink VIEW Certified Configuration Guide: Cisco Controllers and APs

721-1001-000-AH.docx

December 2016 3

Contents

Introduction...................................................................... 4

Certified Product Summary.............................................................................................. 4

`Known Limitations........................................................................................................... 6

Spectralink References .................................................................................................... 6

Support Documents ..................................................................................................... 7

White Papers ............................................................................................................... 8

Product Support ............................................................................................................... 8

Chapter 1: Configuration for Wi-Fi Standard QoS or CCXv4

Operation......................................................................... 9

Overview............................................................................................................................ 9

Network Topology............................................................................................................. 9

Configuring a New Controller Starting from Factory Defaults......................................10

Connecting to the Controller Via a Browser..................................................................10

Installing Software...........................................................................................................11

Controller Setup...............................................................................................................12

Connecting APs...............................................................................................................15

Defining a RADIUS Server...............................................................................................17

AP Configuration .............................................................................................................20

Configuration for use with 2.4 GHz radio.....................................................................21

Configuring 802.11n for 2.4 GHz.................................................................................29

Configuration for use with 5 GHz radio........................................................................30

Configuring 802.11n for 5 GHz....................................................................................37

Setting up the SSID..........................................................................................................40

Setting up the EDCA parameters profile........................................................................50

Configuration for 5 GHz...............................................................................................50

Configuration for or 2.4 GHz........................................................................................50

721-1001-000-AH.docx

December 2016 4

Introduction

Spectralink’s Voice Interoperability for Enterprise Wireless (VIEW) Certification Program is

designed to ensure interoperability and high performance between PIVOT™by Spectralink®

(87-Series) and 84-Series Wireless Telephones and WLAN infrastructure products.

The products listed below have been tested in Spectralink’s lab and have passed VIEW

Certification.

Certified Product Summary

Manufacturer:

Cisco Systems Inc.: www.cisco.com

Certified products:

Controllers:

2100, 2500, 4400, 5500 Series WLC

(Wireless LAN Controller)

3750G Integrated WLC,

WLC Module,

WiSM (Wireless Services Module),

WiSM2, Virtual Controller

APs:

60x

104x

113x

114x

122x

123x

124x

125x

126x

13xx

155x

160x

170x

260x

270x

350x

360x

370x

AP Radio(s):

2.4 GHz (802.11b/g/n), 5 GHz (802.11a/n/ac)

Security:

None, WEP, WPA-PSK, WPA2-PSK, WPA2-Enterprise (EAP-FAST, EAP-

TLS, and PEAPv0/MSCHAPv2) with CCKM (Cisco Centralized Key

Management)** and OKC

QoS:

Wi-Fi Standard for Spectralink PIVOT, 8440/8441/8450/8452/8453

Network topology:

Switched Ethernet (recommended)

AP and WLC software

versions approved:

7.0.250.0 for 60x, AP801, AP802, 104x, 113x, 114x, 122x, 123x, 124x,

125x, 126x, 13xx, 155x and 350x Aps with 2100, 2500, 4400, 3750G, 5500,

7500, WLC SW for SRE, WiSM, WiSM2

7.4.121.0 for 60x, 70x, AP801, AP802, 104x, 113x, 114x, 124x, 125x, 126x,

155x, 160x, 260x, 350x, and 360x with 2500, 5500, 7500, 8500, WiSM2,

WLC SW for SRE, Virtual Controller

7.6.130.0 for 60x, 70x, AP801, AP802, 104x, 113x, 114x, 124x, 125x, 126x,

155x, 160x, 260x, 270x, 350x, 360x, and 370x with 2500, 5500, 7500, 8500,

WiSM2, WLC SW for SRE, Virtual Controller

8.0.115.0 for 170x, 370x with 2500, 5500, 7500, 8500, WiSM2, WLC SW for

SRE or UCS-E, Virtual Controller

8.1.131.0 for 260x, 370x with 2500, 5500, 7500, 8500, WiSM2, WLC SW for

SRE or UCS-E, Virtual Controller

8.3.102.0 for 260x, 270x, ,360x, 370x with 2500, 5500, 7500, 8500, WiSM2,

WLC SW for SRE or UCS-E, Virtual Controller

Spectralink VIEW Certified Configuration Guide: Cisco Controllers and APs

721-1001-000-AH.docx

December 2016 5

Handset* models tested:

PIVOT

Handset radio mode:

802.11b/g & 802.11bgn

802.11a & 802.11an

Meets VIEW minimum call

capacity per AP:

8 calls

10 calls

Handset models tested:

Spectralink 8440/8441/8450/8452/8453 Wireless Telephone

Handset radio mode:

802.11b/g & 802.11bgn

802.11a & 802.11an

Meets VIEW minimum call

capacity per AP:

8 calls

10 calls

*Spectralink handset models and their OEM derivatives are verified compatible with the WLAN hardware

and software identified in the table. Throughout the remainder of this document they will be referred to

collectively as “Spectralink Wireless Telephones”, “phones” or “handsets”. The 8440, 8441 (8440 with

personal alarm hardware), 8450 (with 1D bar code reader), 8452 (with 1D and 2D bar code reader), and

8453 (8452 with personal alarm hardware) handsets will be referred to collectively as the 84-Series

handsets. All PIVOT models will be referred to collectively as PIVOT handsets.

Spectralink VIEW Certified Configuration Guide: Cisco Controllers and APs

721-1001-000-AH.docx

December 2016 6

`Known Limitations

Heavy multicast, broadcast or push-to-talk (PTT) traffic may impair voice quality on 7.0

versions.

Heavy ftp traffic may impair PTT traffic.

Fast Transition Roaming (802.11r) is not supported by the handsets

Multicast by VLAN is not compatible with the PTT feature in the handsets.

When using 7.0 versions, 5 GHz radio, 1142 AP’s, and 80xx handsets, the use of

multiple antennas must be disabled on the AP’s.

When using 1142 AP’s, A-MPDU aggregation must be disabled for a WLAN containing

any 1142’s if 11n is enabled on the network.

A-MSDU aggregation must be disabled if 11n is enabled on the AP.

In the controller software versions considered in this document, there is an issue related

to band steering that can cause slow roaming on the 2.4 GHz band in the 84-Series and

PIVOT handsets when both radios are active in the handset.

In the WMM/QoS mode, it is important to use the Static CAC Method rather than the

Load Based CAC Method.

DTPC (Dynamic Transmit Power Control) and the Auto setting on the 84-series are

recommended for best range performance. PIVOT uses Auto mode exclusively.

For best operation, the RRM/Tx Power Control (TPC) should be set to Fixed on On

Demand (during a low usage period) and the RRM/DCA Algorithm should be set to

Freeze or OFF. The White Paper: Best Practices Guide to Deploying Spectralink 84-

Series Handsets has more information about cell design. The handsets are not

incompatible with these features, but if used frequently, they will cause long roams and

asymmetric coverage regions that will result in choppy calls during caller movement.

The AP 3600 802.11ac snap-in module is not compatible with the Spectralinnk phones.

The AP 3600 without the module passed performance testing.

The F/T (fast transition roaming) adaptive mode where a WLAN can have a mix of

clients that support and don’t support 802.11r worked well on the 2600, 2700, and 3700

models. It did not work well with the AP 3600. This feature was introduced in the 8.3

Cisco software chain.

ipv6 operation has not been tested.

Spectralink References

All Spectralink support documents are available at http://support.spectralink.com.

Spectralink VIEW Certified Configuration Guide: Cisco Controllers and APs

721-1001-000-AH.docx

December 2016 7

To go to a specific product page:

Select the Product Category and Product Type from the dropdown lists and then select the

product from the next page. All resources for that particular product are displayed by default

under the All tab. Documents, downloads and other resources are sorted by the date they were

created so the most recently created resource is at the top of the list. You can further sort the

list by the tabs across the top of the list to find exactly what you are looking for. Click the title to

open the link.

Support Documents

PIVOT by Spectralink Configuration Guide The PIVOT Configuration Guide provides detailed

information about PIVOT menu items that have been developed specifically for the PIVOT

handset.

Spectralink 87-Series Wireless Telephone Deployment Guide The Deployment Guide provides

sequential information for provisioning and deploying the handsets. It covers deployment using

the SLIC tool and CMS as well as manual deployment.

The Spectralink 84-Series Wireless Telephone Administration Guide provides a comprehensive

list of every parameter available on Spectralink 84-Series Wireless Telephones.

The Spectralink 84-Series Deployment Guide is your essential reference for provisioning and

deploying Spectralink 84-Series handsets in any environment.

Spectralink VIEW Certified Configuration Guide: Cisco Controllers and APs

721-1001-000-AH.docx

December 2016 8

The Web Configuration Utility User Guide explains how to use a web browser to configure the

Spectralink 84-Series handsets on a per handset basis.

Best Practices for Deploying Spectralink 87-Series Handsets provides detailed information on

wireless LAN layout, network infrastructure, QoS, security and subnets.

White Papers

Spectralink White Papers are available at http://www.spectralink.com/resources/white-papers.

For the Spectralink 84-Series Wireless Telephones, please refer to Best Practices Guide for

Deploying Spectralink 84-Series Handsets for detailed information on wireless LAN layout,

network infrastructure, QoS, security and subnets.

For additional details on RF deployment please see The challenges of ensuring excellent voice

quality in a Wi-Fi workplace and Deploying Enterprise-Grade Wi-Fi Telephony.

These White Papers identify issues and solutions based on Spectralink’s extensive experience

in enterprise-class Wi-Fi telephony. It provides recommendations for ensuring that a network

environment is adequately optimized for use with Spectralink Wireless Telephones.

Product Support

Note: Converting autonomous APs to Lightweight mode

This document does not cover the steps involved in converting autonomous APs to

Lightweight mode such that they can be controlled by the Cisco WLCs.

Please contact Cisco's Customer Support at www.cisco.com for instructions on this

procedure. Once the APs are converted, this document can be used to provision APs.

Note: RADIUS server configuration

This document does not cover the steps involved to configure a RADIUS server required for

using WPA2-Enterprise or Cisco FSR security types.

Installation and configuration guides for Cisco Wireless LAN Controllers can be found on

Cisco’s website.

To convert Autonomous APs to Lightweight mode, go to:

http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guid

e/lwapnote.html

For other assistance, contact either Cisco’s or Spectralink’s customer service at:

www.cisco.com or www.Spectralink.com

721-1001-000-AH.docx

December 2016 9

Chapter 1: Configuration for Wi-Fi

Standard QoS or CCXv4 Operation

Overview

Spectralink 84-Series and PIVOT handsets only support Wi-Fi Standard QoS. The handsets

are compatible with both networks configured with CCX (Cisco Compatible Extensions) and

networks that are not configured with CCX, but they have not been CCX certified.

Network Topology

Note: Example configuration shown

This is a modified diagram and not all components are shown for every system type.

Spectralink VIEW Certified Configuration Guide: Cisco Controllers and APs

721-1001-000-AH.docx

December 2016 10

Configuring a New Controller Starting from Factory

Defaults

Initial provisioning of the controller is done via the command line interface (CLI).

1 Connect a null modem serial cable between the console port of the controller and the

serial port of a PC.

2 Open a terminal program, such as Hyper Terminal, and configure the port settings to

9600 baud, no parity, 8 data bits and 1 stop bit.

3 Power-on the controller. Status of the controller’s boot process will appear as the

controller is powering up. Once the controller is running, it will prompt you to run the

Startup Wizard.

4 The Startup Wizard provides for an easy means to perform initial controller setup and

provisioning. Refer to the Installation and Startup Guide for the appropriate controller,

found at Cisco’s website. This document contains a detailed explanation of using the

Startup Wizard for the 5500. Once the controller has been configured via the Startup

Wizard, the remaining configuration can be configured through the switch-web interface

using a Web browser.

5 If necessary, the controller can be reset to factory defaults. To reset the WLC to factory

default, you must reboot, then type Recover-config at the CLI. This only works before the

first time a user logs in via the console.

A few advanced commands must be set from the command line interface after the rest of the

controller has been configured. These are noted in the instructions below.

Connecting to the Controller Via a Browser

1 Connect to the WLC by pointing your internet browser to the URL: https<IP_Addr>

(where <IP_Addr> is the IP address of the management interface of the WLC).

2 Click the Login prompt. The default User Name and Password is admin.

Once logged in properly, a page similar to the one below displays on version 8.1+. All

other versions go directly to the screen in step 4.

3 Click the Advanced button on the 8.1 or later version screens.

Andere Handbücher für 2100 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cisco Controller Handbücher

Cisco

Cisco SFS 3504 Bedienungsanleitung

Cisco

Cisco ONS 15454 Series Bedienungsanleitung

Cisco

Cisco 5520 Bedienungsanleitung

Cisco

Cisco 2504 Bedienungsanleitung

Cisco

Cisco Firepower 4100 Series Bedienungsanleitung

Cisco

Cisco 521G - Unified IP Phone VoIP Bedienungsanleitung

Cisco

Cisco 6585 Bedienungsanleitung

Cisco

Cisco Catalyst C9800-L Handbuch

Cisco

Cisco AIR-PCM342 Handbuch

Cisco

Cisco Identiv ICPAM EM-100 Bedienungsanleitung

Cisco

Cisco 2100 Series Bedienungsanleitung

Cisco

Cisco CSC-MEC Bedienungsanleitung

Cisco

Cisco OL-8335-02 Bedienungsanleitung

Cisco

Cisco Cisco mds 9216 - fabric switch Bedienungsanleitung

Cisco

Cisco Flex 7500 Series Kurzanleitung

Cisco

Cisco 8540 - Catalyst Campus Switch Router Modular Expansion... Bedienungsanleitung

Cisco

Cisco SCE 2000 Bedienerhandbuch

Cisco

Cisco Unified Access CT5760 Kurzanleitung

Cisco

Cisco SD2008T-NA Bedienungsanleitung

Cisco

Cisco 4404 - Wireless LAN Controller Bedienungsanleitung

Cisco

Cisco CLG-8202-SEC Bedienungsanleitung

Cisco

Cisco Catalyst 9800-80 Bedienungsanleitung

Cisco

Cisco SCE 1000 and Bedienungsanleitung

Cisco

Cisco AIR-WLC2106-K9 - Wireless LAN Controller... Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung