Cisco Cisco ASA Series Montageanleitung

Mount and Connect

This chapter describes how to rack-mount the ASA, and how to connect the cords and cables. It contains the

following sections

•Rack-mount the ASA , on page 1

•Connect Cables, Turn on Power, and Verify Connectivity, on page 2

•Connect to a Console Terminal or PC, on page 4

Rack-mount the ASA

The ASA ships with rack-mount brackets or “ears,” which you can install on the front or the rear of the chassis.

Follow these steps to install your ASA in a rack.

Step 1 Attach both brackets to the sides of the ASA chassis, either to the front or rear.

After the brackets are secured to the chassis, you can mount it in the rack.

Step 2 Attach the chassis to the rack.

We recommend that you install the chassis with the rear panel facing the cold aisle. (See the following illustration for an

example of air flow from back to front.)

Mount and Connect

Figure 1: Chassis Installed in the Rack

What to do next

You can now install the cables and power cord, as described in Connect Cables, Turn on Power, and Verify

Connectivity, on page 2.

Connect Cables, Turn on Power, and Verify Connectivity

After positioning or mounting the ASA, follow these steps to connect cables, turn on power, and verify

connectivity:

Step 1 Connect the network cables:

a) Management interface – Using this Management 1/1 Gigabit Ethernet port, you can connect a management computer

directly with an Ethernet cable, or you can connect the computer and the ASA to the same management network. Be

sure the PC is configured to obtain an IP address using DHCP.

You can configure any of the Gigabit Ethernet interfaces to be a management-only interface using the

management-onlycommand. However, you cannot disable management-only mode on the Management 1/1 interface.

The following figure shows how to connect the network cables.

Mount and Connect

Connect Cables, Turn on Power, and Verify Connectivity

Figure 2: ASA 5508-X and ASA 5516-X Cabling

Console port (RJ-45 or Mini USB Type B)2Gigabit Ethernet data interface (RJ-45)1

Management 1/1 interface (RJ-45)3

b) (Optional) Console port – For use with the CLI. Connect a computer or terminal server using a serial console cable

to either the RJ-45 or Mini USB Type B port.

Only one console port can be active at a time. When a cable is plugged into the USB console port, the RJ-45 port

becomes inactive. Conversely, when the USB cable is removed from the Mini USB Type B port, the RJ-45 port

becomes active. See Connect to a Console Terminal or PC, on page 4 for specific instructions for connecting the

console port.

c) Gigabit Ethernet ports – For the network interfaces; use standard RJ-45 Ethernet cables.

You can use any available Gigabit Ethernet port on the ASA 5508-X or ASA 5516-X as a failover link. The failover

link interface is not configured as a normal networking interface; it should only be used for the failover link. You

can connect the failover link by using a dedicated switch with no hosts or routers on the link.

Step 2 Connect the power cord to the ASA, and plug the other end to your power source.

Step 3 Press the power switch to turn the appliance on.

When the Power LED is solid green, the ASA is completely powered on.

Step 4 Check the Status LED on the ASA chassis.

When it is solid green, the ASA has passed power-on diagnostics.

Step 5 See the Cisco ASA 5508-X and ASA 5516-X Quick Start Guide to continue setting up your ASA.

Mount and Connect

Connect Cables, Turn on Power, and Verify Connectivity

Your ASA ships with either ASA or Firepower Threat Defense software preinstalled. To reimage your device,

see Reimage the Cisco ASA or Firepower Threat Defense Device.

Note

Connect to a Console Terminal or PC

The serial ports provide administrative access to the ASA either with a console terminal or a PC. To configure

the ASA through the CLI, you must establish a connection between the ASA console port and either a terminal

or a PC.

This section describes how to connect to a console terminal or a PC, and contains the following topics:

Connect to the Console Port with Microsoft Windows

You must install a USB device driver the first time a Microsoft Windows-based PC is connected to the USB

serial port on the ASA, otherwise the connection fails.

To uninstall the driver, use the Add Remove Programs utility or the Setup-exe program.

Disconnect the ASA console terminal before uninstalling the driver.

Note

Step 1 Obtain the appropriate driver (Cisco_usbconsole_driver_X_X_zip, where X is a revision number) for your ASA model

from the Cisco Download Software site, USB Console Software category.

Step 2 Install the driver.

Step 3 Connect a USB 5-pin Mini USB Type B to the USB console port as shown in the following figure.

Mount and Connect

Connect to a Console Terminal or PC

Figure 3: ASA 5508-X and ASA 5516-X Console Port Connection

Mini USB Type B to USB Type

A console cable

2Mini USB Type B console port1

USB Type A3

Step 4 Connect the end of the cable with the DB-9 connector (or USB Type A) to the terminal or PC. If your terminal or PC has

a console port that does not accommodate a DB-9 connector, you must provide an appropriate adapter for that port.

The LED for the console port turns green and within a few moments the Found New Hardware Wizard appears.

Step 5 Follow the instructions to complete the driver installation.

Step 6 To communicate with the ASA, start a terminal emulator application. This software should be configured with the

following parameters:

• 9600 baud

• 8 data bits

• no parity

• 1 stop bit

• no flow control

Connect to the Console Port with Mac OS X

Follow these steps to connect a Mac OS X system USB port to the console using the built-in OS X Terminal

utility, or alternatively you can use a separate terminal emulator application.

Mount and Connect

Connect to the Console Port with Mac OS X

Step 1 Use the Finder to go to Applications > Utilities > Terminal.

Step 2 Connect the OS X USB port to the ASA.

Step 3 Enter the following commands to find the OS X USB port number:

Example:

macbook:user$ cd /dev

macbook:user$ ls -ltr /dev/*usb*

crw-rw-rw- 1 root wheel 9, 66 Apr 1 16:46 tty.usbmodem1a21

DT-macbook:dev user$

Step 4 Connect to the USB port with the following command followed by the ASA USB port speed:

Example:

macbook:user$ screen /dev/tty.usbmodem1a21 9600

Step 5 Enter Ctrl-z followed by Ctrl-\ to disconnect the OS X USB console from the Terminal window.

Connect to the Console Port with Linux

Follow these steps to connect a Linux system USB port to the console using the built-in Linux Terminal utility.

Step 1 Open the Linux Terminal window.

Step 2 Connect the Linux USB port to the ASA.

Step 3 Enter the following commands to find the Linux USB port number:

Example:

root@usb-suse# cd /dev

root@usb-suse /dev# ls -ltr *ACM*

crw-r--r-- 1 root root 188, 0 Jan 14 18:02 ttyACM0

root@usb-suse /dev#

Step 4 Connect to the USB port with the following command followed by the ASA USB port speed

Example:

root@usb-suse /dev# screen /dev/ttyACM0 9600

Step 5 To disconnect the Linux USB console from the Terminal window, enter Ctrl-a followed by : then quit.

Mount and Connect

Connect to the Console Port with Linux

Andere Handbücher für Cisco ASA Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cisco Firewall Handbücher

Cisco

Cisco 5510 - ASA SSL / IPsec VPN Edition Bedienungsanleitung

Cisco

Cisco Firepower 2120 Handbuch

Cisco

Cisco PIX-525-UR-BUN - PIX 525 Unrestricted Bundle Bedienungsanleitung

Cisco

Cisco 5505 - ASA Firewall Edition Bundle Bedienungsanleitung

Cisco

Cisco Small Business RV215W Bedienungsanleitung

Cisco

Cisco PIX 506E - Security Appliance Bedienungsanleitung

Cisco

Cisco Cisco ASA 5500 Series Bedienungsanleitung

Cisco

Cisco 380 Series Handbuch

Cisco

Cisco Small Business RV220W Bedienungsanleitung

Cisco

Cisco TelePresence Server 7010 Bedienungsanleitung

Cisco

Cisco 5505 - ASA Firewall Edition Bundle Handbuch

Cisco

Cisco Meraki MX64 Bedienungsanleitung

Cisco

Cisco Firepower 4100 Series Bedienungsanleitung

Cisco

Cisco Firepower 9300 Handbuch

Cisco

Cisco MEREAKI MX65W Bedienungsanleitung

Cisco

Cisco ASA 5508-X Bedienungsanleitung

Cisco

Cisco S195 Handbuch

Cisco

Cisco 5505 - ASA Firewall Edition Bundle Bedienungsanleitung

Cisco

Cisco IronPort M1070 Bedienungsanleitung

Cisco

Cisco ASA 5506-X Bedienungsanleitung

Cisco

Cisco Spam Bedienungsanleitung

Cisco

Cisco IronPort C370 Bedienungsanleitung

Cisco

Cisco 881W - Integrated Services Router Wireless Bedienungsanleitung

Cisco

Cisco Cisco ASA 5510 Bedienungsanleitung

Beliebte Firewall Handbücher anderer Marken

Fortinet

Fortinet FortiGate Voice Series Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 2300 Bedienungsanleitung

SecureLogix

SecureLogix ETM System Bedienungsanleitung

NETGEAR

NETGEAR ProSafe FVX538 Bedienungsanleitung

Lanner

Lanner FW-8877 Bedienungsanleitung

Huawei

Huawei USG6000 Series Installations- und Betriebshandbuch

H3C

H3C SecPath F5000-AI-15 Bedienungsanleitung

Nexcom

Nexcom DNA 1150 Bedienungsanleitung

Fortinet

Fortinet FortiGate-60 series Bedienungsanleitung

Draytek

Draytek Vigor2860 Series Bedienungsanleitung

Lanner electronics

Lanner electronics FW-7650 Series Bedienungsanleitung

Swisscom

Swisscom Internet Backup Bedienungsanleitung

SonicWALL

SonicWALL NSa 5700 Bedienungsanleitung

DPtech

DPtech FW1000 SERIES Bedienungsanleitung

FEITIAN

FEITIAN MultiPass FIDO Bedienungsanleitung

EBLOCKER

EBLOCKER PRO Bedienungsanleitung

GTA

GTA GB-200 Bedienungsanleitung

Trend Micro

Trend Micro Deep Edge Bedienungsanleitung