Cisco Firepower 2100 Series Kurzanleitung

Firepower Easy Deployment Guide for Cisco

Firepower 1000 or 2100 Firewalls

First Published: 2020-10-28

Last Modified: 2021-05-18

Firepower Easy Deployment Guide for Cisco Firepower 1000 or 2100

Firewalls

This document provides information about two easy deployment options for customers of Firepower Threat

Defense (FTD) version 6.7 and later: Low-Touch Provisioning for Cisco Defense Orchestrator (CDO) customers

and Remote Branch Office Deployment for Firepower Management Center (FMC) customers.

• See Low-Touch Provisioning Using CDO, on page 1 if your job is to connect a new Firepower firewall

to your network or to manage that new firewall with CDO.

• See Remote Branch Office Deployment of FTD Devices for Management by an FMC, on page 7 if

you are an FMC administrator and want to manage an FTD at a remote branch using FMC.

Low-Touch Provisioning Using CDO

Low-touch provisioning allows anybody to connect a new Firepower 1000 or 2100 series device to their

network so that their IT department can onboard the device to CDO and configure it remotely.

What do you want to do?

•Connect a New Cisco Firepower Firewall to Your Network. I work at the branch office.

•Onboard a Firepower Firewall to CDO Using its Serial Number. I am the CDO administrator.

Connect a New Cisco Firepower Firewall to Your Network

This topic describes the process of connecting your Firepower firewall to your network so that it can be

managed remotely by a CDO administrator.

If you received a Firepower firewall at your branch office and your job is to plug it in to your network,

watch this video.

The video describes your firewall and the LED sequences on the device that indicate the device's status. If

you need to, you'll be able to confirm the device's status with your IT department just by looking at the LEDs.

These are the steps described in the video:

1. Your Firepower firewall needs to be one of a certain model number and needs to have FTD version 6.7

installed on it for low-touch provisioning to work. The table below shows the Firepower models that

support low-touch provisioning.

Firepower Easy Deployment Guide for Cisco Firepower 1000 or 2100 Firewalls

To make sure the Firepower model has the right software installed, look on the cardboard box the device

came in. It should have a plain white sticker on it with a product identifier that looks similar to one in the

following table:

FTD 6.7 Product IdentifiersFirepower Model Numbers that Support Low-Touch

Provisioning

SF-F1K-TD6.7-K9Firepower 1000 series device models:

1010, 1120, 1140, 1150

SF-F2K-TD6.7-K9Firepower 2100 series device models:

2110, 2120, 2130, 2140

2. Before you rack the device or throw the cardboard box away, record your device's serial number and send

it to your IT department. They will need it to manage the device. The serial number of the device is located

on the cardboard box the device came in and on a sticker affixed to the device itself. See Find Your

Device's Serial Number, on page 4 for more information.

3. Unpack the box and take inventory of the contents.

Keep the cardboard box until you have plugged in the device, you have connected it to your network, and

the device has successfully contacted the Cisco cloud.

4. Connect the device to power.

5. Connect the network cable from the Ethernet 1/1 interface to your wide area network (WAN) modem.

Your WAN modem is your branch's connection to the internet and will be your Firepower firewall's route

to the Internet as well.

Do not connect the network cable from the device's Management interface to your WAN.

Note

Figure 1: Firepower 1010 Cabling

Firepower Easy Deployment Guide for Cisco Firepower 1000 or 2100 Firewalls

Connect a New Cisco Firepower Firewall to Your Network

Figure 2: Firepower 1100 Cabling

Figure 3: Firepower 2100 Cabling

6. Observe the Stauts/SYS LED light pattern on the device to determine if the device has reached the Cisco

cloud. The table below provides the LED light patterns and the approximate time they occur. It may take

a little more time or a little less time for the Firepower device to reach the Cisco cloud based on network

conditions and the Firepower model you are working with.

Time this ocurs after the

device is powered on.

(minutes:seconds)

DescriptionLight pattern of Stauts/SYS LED

01:00The device is booting up

correctly.

Fast flashing green

01:00The device failed to boot

correctly.

Fast flashing amber

10:00The application is loaded on the

device.

Solid green

Firepower Easy Deployment Guide for Cisco Firepower 1000 or 2100 Firewalls

Connect a New Cisco Firepower Firewall to Your Network

Time this ocurs after the

device is powered on.

(minutes:seconds)

DescriptionLight pattern of Stauts/SYS LED

10:00The application failed to load

correctly on the device.

Solid amber

15:00The device is connected to the

Cisco cloud.

Slow flashing green

15:00The device failed to connect to

the Cisco cloud.

Alternating green and amber

After you complete this task, your IT administrator will be able to configure the firewall remotely. You're

done.

Onboard a Firepower Firewall to CDO Using its Serial Number

If you are a Cisco Defense Orchestrator (CDO) administrator and someone at a branch office has connected

anew Cisco Firepower firewall running Firepower Threat Defense version 6.7 or later device to their network,

and your job is to onboard it to CDO using its serial number, see Procedure for Onboarding an FTD using the

Device's Serial Number

If you are a CDO administrator and your task is to onboard a fully configured Cisco Firepower firewall running

Firepower Threat Defense 6.7 or later, here are two other methods of onboarding the device to CDO:

•Onboard an FTD Using a Registration Key

•Onboard an FTD Using the Device's Serial Number

Find Your Device's Serial Number

Your IT department needs your Firepower firewall's serial number to connect to the device and manage it

remotely. You can find the serial number in a couple of different places.

The Sticker on the Cardboard Box

The serial number is printed on the sticker on the cardboard box the firewall came in. Here is an example:

Firepower Easy Deployment Guide for Cisco Firepower 1000 or 2100 Firewalls

Onboard a Firepower Firewall to CDO Using its Serial Number

The Sticker on the Chassis

Firepower 1010: The serial number is on a sticker on the bottom of the device:

Firepower 1100: The serial number is on a sticker on the back of the device or on the bottom of the device:

Firepower 2100: The serial number is on a sticker on a pull-out tab on the front of the device:

Firepower Easy Deployment Guide for Cisco Firepower 1000 or 2100 Firewalls

Find Your Device's Serial Number

Connecting to the Firewall Using a Console Cable

You can connect a console cable from a device like a laptop to your Firepower firewall, open up a terminal

window, and enter a few commands to display the device's serial number.

This procedure is for advanced users who are comfortable working with a command line interface and, possibly,

installing software drivers on their laptops. Here is the procedure to connect a computer to the Firepower

firewall using a console cable and to retrieve the device's serial number in a terminal window:

Note

1. See "Connect to the Console Port" for instructions on how to connect a laptop to your device using a

console cable. Though the commands are explained in the Firepower 1010 Hardware Installation Guide,

they will be the same for the 1100 series devices and 2100 series devices.

There are two types of console ports for the 1010 and 1100 series devices. You could use either the

"USB-A to B" console cable that came with the firewall or a DB-9 to RJ-45 serial cable.

The Firepower 2100 ships with only a DB-9 to RJ-45 serial cable. When using this cable, you will need

a third party serial-to-USB cable to make the connection. Be sure to install any necessary USB serial

drivers for your operating system.

2. Log in to the device as the admin user. If the device has not been configured, you will be asked to create

a new password for the admin.

3. At the firepower# prompt, type show chassis detail. Here is an example:

firepower# show chassis detail

Chassis:

Chassis: 1

Overall Status: Operable

Oper qualifier: N/A

Operability: Operable

Product Name: Cisco Firepower 1010 Security Appliance

PID: FPR-1010

VID: V01

Vendor: Cisco Systems, Inc

Serial (SN): JMX2405X0R9

Firepower Easy Deployment Guide for Cisco Firepower 1000 or 2100 Firewalls

Find Your Device's Serial Number

HW Revision: 0.6

PCB Serial Number: JAD24040S6L

Power State: Ok

Thermal Status: Ok

Boot Status: OK

Current Task:

firepower#

The output shows two serial numbers. Report the value of Serial (SN) field to your IT department.

Remote Branch Office Deployment of FTD Devices for Management by an

FMC

You can deploy the Firepower Threat Defense (FTD) at a remote branch office using a Firepower Management

Center (FMC) at a central headquarters.

• An administrator at the central headquarters pre-configures the FTD at the CLI, and then sends the FTD

to the remote branch office.

• The branch office administrator cables and powers on the FTD.

• The central administrator completes configuration of the FTD using the FMC.

See the getting started guide for your model for more information:

•Firepower 1010

•Firepower 1100

•Firepower 2100

Firepower Easy Deployment Guide for Cisco Firepower 1000 or 2100 Firewalls

Remote Branch Office Deployment of FTD Devices for Management by an FMC

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS,

INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND,

EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH

THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY,

CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB's public domain version of

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS" WITH ALL FAULTS.

CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF

MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT

LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS

HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network

topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional

and coincidental.

All printed copies and duplicate soft copies of this document are considered uncontrolled. See the current online version for the latest version.

Cisco has more than 200 offices worldwide. Addresses and phone numbers are listed on the Cisco website at www.cisco.com/go/offices.

Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL:

https://www.cisco.com/c/en/us/about/legal/trademarks.html. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a

partnership relationship between Cisco and any other company. (1721R)

Andere Handbücher für Firepower 2100 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cisco Firewall Handbücher

Cisco

Cisco ASA 5512-X Bedienungsanleitung

Cisco

Cisco ASA 5506-X Bedienungsanleitung

Cisco

Cisco ASA 5555-X Bedienungsanleitung

Cisco

Cisco Firepower 4110 Bedienungsanleitung

Cisco

Cisco Cisco ASA Series Bedienungsanleitung

Cisco

Cisco Small Business RV220W Bedienungsanleitung

Cisco

Cisco 881W - Integrated Services Router Wireless Bedienungsanleitung

Cisco

Cisco Spam Bedienungsanleitung

Cisco

Cisco Firepower 2100 Series Bedienungsanleitung

Cisco

Cisco Small Business RV220W Bedienungsanleitung

Cisco

Cisco Firepower 1010 Handbuch

Cisco

Cisco FPR1010-ASA-K9 Bedienungsanleitung

Cisco

Cisco PIX 506E - Security Appliance Bedienungsanleitung

Cisco

Cisco 5510 - ASA SSL / IPsec VPN Edition Bedienungsanleitung

Cisco

Cisco M195 Handbuch

Cisco

Cisco ASA 5512-X Handbuch

Cisco

Cisco Firepower 4100 Series Handbuch

Cisco

Cisco 5580-40 - ASA Firewall Edition Handbuch

Cisco

Cisco Firepower 4100 Series Installationshandbuch

Cisco

Cisco Firepower 1100 Bedienungsanleitung

Cisco

Cisco 5505 - ASA Firewall Edition Bundle Bedienungsanleitung

Cisco

Cisco M690 Bedienungsanleitung

Cisco

Cisco ASA 5506-X Montageanleitung

Cisco

Cisco RV110W Bedienungsanleitung

Beliebte Firewall Handbücher anderer Marken

Fortinet

Fortinet FortiGate Voice Series Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 2300 Bedienungsanleitung

SecureLogix

SecureLogix ETM System Bedienungsanleitung

NETGEAR

NETGEAR ProSafe FVX538 Bedienungsanleitung

Lanner

Lanner FW-8877 Bedienungsanleitung

Huawei

Huawei USG6000 Series Installations- und Betriebshandbuch

H3C

H3C SecPath F5000-AI-15 Bedienungsanleitung

Nexcom

Nexcom DNA 1150 Bedienungsanleitung

Fortinet

Fortinet FortiGate-60 series Bedienungsanleitung

Draytek

Draytek Vigor2860 Series Bedienungsanleitung

Lanner electronics

Lanner electronics FW-7650 Series Bedienungsanleitung

Swisscom

Swisscom Internet Backup Bedienungsanleitung

SonicWALL

SonicWALL NSa 5700 Bedienungsanleitung

DPtech

DPtech FW1000 SERIES Bedienungsanleitung

FEITIAN

FEITIAN MultiPass FIDO Bedienungsanleitung

EBLOCKER

EBLOCKER PRO Bedienungsanleitung

GTA

GTA GB-200 Bedienungsanleitung

Trend Micro

Trend Micro Deep Edge Bedienungsanleitung