Cisco CIAG-GW-IP10 Bedienungsanleitung

CHAPTER

4-1

Cisco Physical Access Gateway User Guide

OL-20932-01

Connecting a Cisco Input Module

Overview

The optional Cisco Input Module (Figure 4-1) is attached to a Cisco Physical Access Gateway or Cisco

Reader Module to provide additional connections for up to ten input devices. Each connection can be

configured as supervised or unsupervised. A supervised connection is a four- state connection to

determine if the connection is (1) short (2) is open (3)normal state or (4) alarm state. An unsupervised

input indicates only normal or alarm.

Figure 4-1 Cisco Input Module

4-2

Cisco Physical Access Gateway User Guide

OL-20932-01

Chapter 4 Connecting a Cisco Input Module

Package Contents

The optional Cisco Input Module is connected to a Cisco Physical Access Gateway or Cisco Reader

Module using a CAN connection to provide connections for additional input devices, as, as shown in

Figure 4-2.

Figure 4-2 Cisco Reader Module connected to the Cisco Physical Access Gateway

Package Contents

Each Cisco Input Module includes the following:

•20 resistors (1K) for input supervision

•2 mounting brackets, with 4 screws for each bracket

•Regulatory compliance and safety information

•Quick start guide

271597

Cisco

IP Network

Additional

Input/Output devices

Additional

Input/Output devices

Door Readers

and Input/Output

devices

Door Readers

and Input/Output

devices

Cisco Input or Output

Module (Optional)

Cisco Input or Output

Module (Optional)

Cisco Reader

Module (Optional)

Cisco

Access Gateway

Cisco Access

Control Manager

CAN connection

Ethernet

Access Layer

switch

4-3

Cisco Physical Access Gateway User Guide

OL-20932-01

Chapter 4 Connecting a Cisco Input Module

Physical Overview and Port Description

•Connector plugs:

Physical Overview and Port Description

Each Cisco Input Module includes 10 ports for connecting additional input devices. as shown in

Figure 4-3.

Figure 4-3 Cisco Input Module Ports and Connectors

Type Quantity

3 Pin 1

2 Pin 13

187043

4-4

Cisco Physical Access Gateway User Guide

OL-20932-01

Chapter 4 Connecting a Cisco Input Module

Physical Overview and Port Description

Figure 4-4 Cisco Input Module Ports and Connectors: Top View

The following items are shown in Figure 4-3 and Figure 4-4:

45 6

187039

Type Description

1Power Two-pin connector for Voltage In (VIN) and Ground (GND) to

connect a 12 to 24 VDC external power source.

2CAN interface A 3-wire CAN bus is used to connect additional modules.

Note Modules are connected using the CAN1 interface. The

CAN2 interface is not supported in this release.

3CAN Terminator The CAN terminator switch is set to ON for the last device in a CAN

wiring bus. This switch is set to set to OFF for all other devices in

the CAN bus.

4Input connections Ten input interfaces used to sense the contact closure. Each input

can be configured as supervised or unsupervised and can be

configured to sense a Normally Open (NO) or Normally Closed

(NC) contact.

•An unsupervised input senses a simple contact closure state,

including Normal or Alarm. When connected to open contacts,

the terminal voltage range is 4V to 5V. For closed contacts, the

voltage range is 0V to 0.7V.

•A supervised input senses four contact states, including

Normal, Alarm, Open and Short. These inputs require 1K

End-Of-Line (EOL) termination resistors installed at the

contacts (two resistors are included in the accessory kits for

each Input port).

4-5

Cisco Physical Access Gateway User Guide

OL-20932-01

Chapter 4 Connecting a Cisco Input Module

Installing the Cisco Input Module

Status LEDs

Each input port includes a status LED that indicates the following information:

Installing the Cisco Input Module

Install a Cisco Input Module is provide additional input connections for a Cisco Reader Module or

Gateway

Before You Begin

Verify the following:

•Verify that the module has access to a power source. See Power Options and Requirements,

page 1-10 for more information.

•Verify that you have the necessary mounting brackets or other hardware. See Mounting a Gateway

or Optional Module, page 1-12.

Installation Procedure

To install the module, perform the following procedure:

Step 1 Mount the module to a wall. See Mounting a Gateway or Optional Module, page 1-12 for more

information.

8PF Power fail input: an unsupervised input that raises a “power fail”

alarm when the circuit is open. Can be configured as an additional

unsupervised port. The corresponding LED is red when circuit is

open (when no input is connected).

9TM Tamper input: an unsupervised input that raises a “tamper” alarm

when the circuit is open. Can be configured as an additional

unsupervised port. The corresponding LED is red when circuit is

open (when no input is connected).

Type Description

Table 4-1 Input Module LEDs

Status Description

OFF Input is not configured

GREEN Input is configured and in normal state

BLINKING GREEN Input is configured, and is receiving and alarm or other data.

BLINKING RED Input is configured, short

RED Input is configured, open

4-6

Cisco Physical Access Gateway User Guide

OL-20932-01

Chapter 4 Connecting a Cisco Input Module

Installing the Cisco Input Module

Step 2 Connect the module to the DC power source:

a. Insert a two-pin connector plug into the DC power port (Figure 4-5)

b. Connect the Voltage In (VIN) and ground (GND) wires.

See Power Options and Requirements, page 1-10 for more information.

Figure 4-5 Power Connections for the Input and Output Modules

The following items are shown in Figure 4-5:

Step 3 Connect the module to the CAN bus:

a. Insert a three-pin connector plug into the CAN1 port, as shown in Figure 4-6.

b. Connect the CAN wires to the CAN bus, as shown in Figure 4-7

c. Turn the CAN terminator ON if the device is the last device in a CAN wiring bus.

Note The CAN terminator switch in included on the Reader, Input and Output modules only (the Gateway is

always the first device in the CAN bus). Set the terminator switch to OFF for all other modules in the

CAN bus.

Note The CAN2 interface is not supported in this release.

See Optional Expansion Modules, page 1-6 for more information.

271599

Configuration Description

1DC power

GND (ground)

Connects the DC ground wire to the module.

2DC power

Voltage In (VIN)

Connects the DC Voltage In (VIN) wire to the module.

4-7

Cisco Physical Access Gateway User Guide

OL-20932-01

Chapter 4 Connecting a Cisco Input Module

Installing the Cisco Input Module

Figure 4-6 CAN Connections: Input and Output Modules

The following items are shown in Figure 4-6:

Figure 4-7 CAN Bus Wiring

Step 4 Connect input devices to the module:

a. Insert two-pin connector plugs into the input ports.

b. (Optional, for supervised input connections only). Install two End-Of-Line (EOL) 1K termination

resistors in each supervised input interface (one terminator in each connector). Figure 4-8 shows the

terminator installation for a Normally Closed (NC) and Normally Open (NO) input connection.

271598

Configuration Description

1CAN+ Connects to the positive terminal of the CAN bus.

2CAN- Connects to the negative terminal of the CAN bus.

3Shield Connects to GND and/or Shield.

3CAN Terminator Turn the terminator ON if the device is the last device in a CAN wiring

bus.

271589

Gateway Module Reader Module Input Module Output Module

CAN+

CAN-

Sheild

4-8

Cisco Physical Access Gateway User Guide

OL-20932-01

Chapter 4 Connecting a Cisco Input Module

Installing the Cisco Input Module

Figure 4-8 Input Connections: Cisco Physical Access Gateway and Reader Module

c. Connect the wires from the input devices.

Note Each of the input connections can be configured as supervised or unsupervised. The tamper

(TM) and power fail (PF) inputs can be configured as additional unsupervised ports. A

supervised input supports four states: normal, alarm, open and short. An unsupervised input

indicates only normal or alarm.

Step 5 See the Cisco Physical Access Manager User Guide for information to configure the module ports.

1K,, 1%

187838

Inhaltsverzeichnis

Andere Cisco E/A-System Handbücher

Cisco

Cisco Nexus 7000 Series Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung