Cisco Media Converter Bedienungsanleitung

QUICK START GUIDE

Installing the Cisco Coaxial Media Converter

Revised: April 24, 2014, 78-21661-01

Before installing the Cisco Coaxial Media Converter (CMC), review the safety precautions in the

Cisco Remote-PHY Solution Installation and Configuration Guide.

For more information see:

www.cisco.com/c/en/us/td/docs/cable/RemotePhy/InstallConfig/guide/b-remotePHY-install-config-guide.html

382520

CATV

Input

Power Fiber

RF Output

RJ-45

Grounding

Screw

Step 1 Install F-Connector on the Cisco CMC:

a. Unscrew the six ½-inch closure bolts on Cisco CMC lid using a torque wrench and open the lid.

b. Cisco CMC supports PG11 and 5/8” F-connectors. Trim the F-connector with a heavy-duty wire cutters to match the

F-connector strip on the Cisco CMC. To use PG11 F-connector, remove the PG11 to 5/8” adapter from the port with a

torque wrench.

c. Lightly loosen the seizure screw. Do not remove it. Install the F-connector into the RF port and tighten the connector

nut with a torque wrench and then tighten the seizure screw using a slot screwdriver.

d. Install a 5/8” port plug into each unused RF port.

e. Close the lid and lightly tighten the six ½-inch closure bolts.

Step 2 Mount the Cisco CMC either on a wall or strand. The maximum weight of the Cisco CMC is 11.8 kg (26 lb).

•Wall-Mounting

a. Drill four holes in the wall at a distance of 291 mm x 158.4 mm. Align the Cisco CMC horizontally with the holes on

the wall and ensure proper ventilation around it.

b. Insert an M8 or 5/16” expansion bolt into each hole.

382482

35mm

32mm

PG11 Strip

Strip

5/8” Strip

CATV IN Port

382483

PORT 1

F-Connector

Seizure Screw

382485

Mounting Holes

291mm

158.4mm

•Strand-Mounting

a. The minimum diameter of the strand should be 5/16”. Loosen the strand clamp bolts to separate the clamps enough to

insert the strand. Position the Cisco CMC on the strand and lightly tighten the strand clamp bolts with your finger.

b. Move the Cisco CMC on the strand as required for installing the cables and tighten the strand clamp bolts using a torque

wrench and ½-inch socket from 5 ft-lb to 8 ft-lb.

Step 3 Open the Cisco CMC lid to perform one or all of the following:

a. To connect the RJ-45 cable, remove the RJ-45 PG16 port plug. Insert the RJ-45 cable through the PG16 gland and the

RJ-45 port. Then, plug in the RJ-45 connector into the GE port. Tighten the PG16 gland into the RJ-45 port using a

torque wrench (4.44 ft-lb) and then tighten the dome cap using a torque wrench (2.44 ft-lb).

b. To connect the optical fiber to the SFP module, remove the 5/8” port plug. Insert the SFP module into the SFP cage, if

not already installed. Insert the optical fiber into the fiber port and then insert the connector into the SFP module port.

Secure the optical fiber using the cable clips as shown in the figure. Seal the fiber port after the installation. Supported

SFPs include EPON SFP, GPON SFP, and GE SFP.

c. To connect the optical fiber to the FRx module, remove the 5/8” port plug. Insert the optical fiber into the fiber port and

connect it to the SC-SC adapter as shown in the figure. Secure the optical fiber using the cable clips. Seal the fiber port

after the installation.

382486

Strand Clamps

Strand

GE1

GE0

SFP0 SFP1

Optical Fiber

PG16 Gland

Cable Clips

Fiber Port

RJ-45 Cable

382519

GE1

GE0

SFP0 SFP1

382518

Cable Clips

SC-SC Adapter

FRx Module

Fiber Port

Optical Fibers

Printed in the USA on recycled paper containing 10% postconsumer waste.

78-21661-01

Americas Headquarters

Cisco Systems, Inc.

San Jose, CA

Asia Pacific Headquarters

Cisco Systems (USA) Pte. Ltd.

Singapore

Europe Headquarters

Cisco Systems International BV Amsterdam,

The Netherlands

Cisco has more than 200 offices worldwide. Addresses, phone numbers, and fax numbers are listed on the Cisco Website at www.cisco.com/go/offices.

Step 4 Connect the coaxial cables as required.

Step 5 Attach one end of an 18-gauge or larger wire to the grounding screw on the Cisco CMC using the M4 panhead Phillips

screw. Then, attach the other end of the grounding wire to an appropriate ground source.

Step 6 For 220V, connect the AC power cord to an AC power source. For 60V, connect the coaxial cable to the CATV IN or

one of the RF output ports. Then, insert an AC shunt for the coaxial cable. Power on the Cisco CMC. It may take up

to three minutes for the Cisco CMC to come Online.

Step 7 Verify if the PWR and STATUS LEDs are green, UPLINK LED is green or blinking green, and ALARM LED is OFF, to

ensure that the Cisco CMC is operational.

Step 8 Close the lid and tighten the six ½-inch closure bolts from 5 ft-lb to 12 ft-lb in the correct sequence as shown in the

figure below using a torque wrench.

382484

Closure Bolts

3 1 5

2 4

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cisco Medienkonverter Handbücher

Cisco

Cisco D9054 Betriebsanleitung

Cisco

Cisco TwinGig CVR-X2-SFP Kurzanleitung

Cisco

Cisco UCS Bedienungsanleitung

Cisco

Cisco ONS 15454 SDH E1-75 Bedienungsanleitung

Cisco

Cisco D9040 Fehlerbehebungshandbuch

Cisco

Cisco 9865 Bedienungsanleitung

Cisco

Cisco Cisco Aironet 1100 Bedienungsanleitung

Cisco

Cisco 2000 Bedienungsanleitung

Cisco

Cisco GigaStack WS-X3500-XL Handbuch

Cisco

Cisco WS-G5486 Installations- und Betriebshandbuch

Cisco

Cisco Explorer Series Bedienungsanleitung

Beliebte Medienkonverter Handbücher anderer Marken

SoundTraxx

SoundTraxx Blunami BLU-2200 Bedienungsanleitung

SPROLINK

SPROLINK VA1 Bedienungsanleitung

Acclaim Lighting

Acclaim Lighting DDC-1-AC Bedienungsanleitung

Nikon

Nikon AF-S TC-20E III Bedienungsanleitung

Axis

Axis AXIS Q7406 Bedienungsanleitung

Omega

Omega TAC80B-J Bedienungsanleitung

Zoom

Zoom Thunderbolt TAC-2R Bedienungsanleitung

OST

OST iConverter 10/100M Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

birddog

birddog MINI Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Wallenstein

Wallenstein WX310 Bedienungsanleitung

Pace

Pace MSS 200-1 Bedienungsanleitung

Solar Converters

Solar Converters EQ 12/24-50 Bedienungsanleitung

CYP

CYP EL-7400V Bedienungsanleitung

TIE

TIE MIDI 1i1o Bedienungsanleitung

DCS

DCS Vivaldi Upsampler Bedienungsanleitung

Westermo

Westermo MCW-211 SERIES Bedienungsanleitung