Cisco MERAKI CW9166D1 Bedienungsanleitung

CW9166D1 Installation Guide

The Cisco Catalyst Wireless 9166D1 is a tri-band enterprise-class WiFi 6E cloud-managed access point supporting the 2.4 G z, 5 G z, and the newly opened

unlicensed 6 G z frequency bands. Designed for the ultra-high capacity and highest density, these APs meet the needs of the most demanding and mission-

critical environments. The Catalyst Wireless 9166D1 is designed with an integrated directional antenna allowing the coverage pattern to favor the area the AP is

facing - ideal for warehouse, auditoriums, etc. The access point includes a fourth radio dedicated to optimizing the RF environment and securing the airwaves.

The AP also has an additional Bluetooth Low Energy (BLE) capable radio used for location and other IoT applications. In addition, the CW9166D1 has a USB

port.

About this Guide

This guide provides instructions on how to install and configure your CW9166D1 access points. This guide also provides mounting instructions and limited

troubleshooting procedures. For more wireless installation guides, refer to the wireless installation guides section on our documentation website.

Product Overview

Physical Specifications

CW9166D1

Interfaces

• 1x 100/1000/2.5G/5G BASE-T Ethernet (RJ45)

• 1x DC power connector (8 mm, center positive)

Power

• Power over Ethernet: 42.5 - 57 V (802.3at and 802.3bt compliant)

• Power consumption: 30W to 40W (802.3at required)

• Power over Ethernet injector (MA-INJ-6) and DC adapter (MA-PWR-50WAC)

Power over Ethernet injector and DC adapter sold separately

Actual power consumption may vary depending on the AP usage

USB will be disabled when powered by 802.3 at/PoE+

It is recommended that you ensure that LLDP is enabled to allow proper power negotiation

Environment

• Operating temperature: -4 °F to 122 °F (-20°C to 50 °C)

• Storage and Transportation Temperature: -4 °F to 122°F (-20 °C to 50 °C)

• umidity: 0 to 90% non-condensing

Physical Security

• Kensington lock hardpoint

* Screws that can be attached to the security hasp of the universal mounting bracket

• Concealed mount plate with anti-tamper cable bay

Product View and Physical Features

Your CW9166D1 has the following features:

A - Cable access bay

B - LED indicator

C - USB Slot - with protective cover

D - USB Slot - with protective cover

E - Rubber stands

F - Ports location

G - Kensington lock slot

H - USB Slot - with protective cover

I - 5Gb ethernet port

J - RJ45 console port (Not Available in Meraki Mode)

K - Reset button

L - Kensington lock slot

M - DC 54V power input port

N - Security hasp for padlocking AP to mounting bracket

The Meraki AP comes with the default Cisco universal mounting bracket (AIR-AP-BRACKET-2) that has the following features:

O - Security Hasp

P - Access Point Mounting Keyholes

Q- T-rail attachment points

R - Cable access slot

The Meraki AP comes with an articulating arm (CW-MNT-ART2-00) that has the following features:

1 - M4 X 10mm screw with washer

2 - AIR-AP-BRACKET-2 (Not included in this kit.)

3 - Access point bracket plate

4 - M8 x40 Hex bolts

5 - Mounting arm

6 - M8 washer (external-tooth)

7 - M8 flanged lock nut

8 - Pole or wall mounting flange

Security Features

These AP feature multiple options for physically securing the access point after installation:

1. Security hasp – The universal mounting bracket has a security hasp and can be used to secure the access point to the universal mounting bracket. Engaging

the security screw prevents accidental dislodging and theft.

2. Kensington lock – The access point contains a hard point that allows it to be secured to any nearby permanent structure using a standard Kensington lock.

Ethernet Ports

The CW9166D1 features one RJ45 port capable of operating at 100/1000/2.5G/5G BASE-T Ethernet (RJ45).

5G, ?

The labeled “5G, ?” accepts 802.3at and 802.3bt power. This port is typically used as the primary uplink to your LAN/WAN.

Warning: AP does not support 802.3af as a power source

Power Source Options

These AP can be powered by a single M-Gig 802.3bt capable UPoE port, allowing for full operation including providing up to 4.5W of power to the USB port. The

AP is capable of operating at its full capacity when powered by a single 802.3at power source, however, the USB port will be disabled.

The table below indicates the different modes of PoE power input and the expected operation of the AP

Port0 2.4GHz 5GHz 6GHz Scan IoT USB

AT 4x4 4x4 4x4 ON ON OFF

BT 4x4 4x4 4x4 ON ON ON

CW9166D1 AP can be powered by PoE power in different modes as mentioned above when using a PoE capable switch. They can also be powered by a single

802.3bt capable PoE injector MA-INJ-6 Meraki multiGigabit 802.3bt Power over Ethernet Injector. It can also be powered by an AC power adaptor MA-

PWR-50WAC - Meraki AC Adapter for MR Series.

Factory Reset Button

If the button is pressed and held for at least five seconds and then released, the AP will reboot and be restored to its original factory settings by deleting all

configuration information stored on the unit.

Package Contents

The access point packages contain the following:

CW9166D1 Cloud-Managed Access Point

Cisco Universal Mount Bracket - AIR-AP-BRACKET-2

Cisco Articulating Arm - CW-MNT-ART2-00 (Optional)

Inhaltsverzeichnis

Andere Cisco Netzwerk-Hardware Handbücher

Cisco

Cisco Secure Network Server 3700 Series Handbuch

Cisco

Cisco ASA 5506-X Handbuch

Cisco

Cisco CVPN3002-K9 - Fast Ethernet VPN Gateway Bedienungsanleitung

Cisco

Cisco ASR 901S Series Betriebsanleitung

Cisco

Cisco WBPN Bedienungsanleitung

Cisco

Cisco Catalyst 8300 Series Handbuch

Cisco

Cisco NTP-E157 Stücklistenhandbuch

Cisco

Cisco MA-UMNT-MR-A3 Bedienungsanleitung

Cisco

Cisco 1230AG - Aironet - Wireless Access Point Bedienungsanleitung

Cisco

Cisco ONS 15216-MD-40-ODD Bedienungsanleitung

Cisco

Cisco CGR 1000 Series Bedienungsanleitung

Cisco

Cisco AIR-BR1410A-A-K9 - Aironet 1410 Wireless... Bedienungsanleitung

Cisco

Cisco ASR 5000 Bedienungsanleitung

Cisco

Cisco ONS 15454 SDH Handbuch

Cisco

Cisco NCS 1000 Bedienungsanleitung

Cisco

Cisco ONS 15540 ESP Handbuch

Cisco

Cisco NSS2000 - Gigabit Storage System Chassis Anleitung zur Verwendung

Cisco

Cisco Remote PHY Shelf 7200 Installationshandbuch

Cisco

Cisco NCS 1001 Handbuch

Cisco

Cisco Fourth-Generation Versatile Interface Processor... Bedienerhandbuch

Cisco

Cisco TELEPRESENCE MCU ACCESSING CONFERENCES - Bedienungsanleitung

Cisco

Cisco Cisco ASA Series Bedienungsanleitung

Cisco

Cisco ONS 15454 Bedienungsanleitung

Cisco

Cisco CSC-C2FCIT Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Arista

Arista CCA-ETM-Q12 Bedienungsanleitung