Cisco 2600 Series Bedienungsanleitung

CHAPTER

3-1

Cisco 2600 Series Routers Hardware Installation Guide

OL-2171-02

Installing the Router

This chapter guides you through the installation of the Cisco 2600 series routers and includes the

following sections:

•Required Tools and Equipment, page 3-1

•Setting Up the Chassis, page 3-2

•Connecting the DC Power Supply, page 3-12

•Power on the Router, page 3-17

•Connecting to a Network, page 3-17

•Connecting the Console Terminal and Modem, page 3-20

•What to Do After Installing Router Hardware, page 3-22

Warning

Onlytrainedandqualifiedpersonnelshouldbeallowedtoinstallorreplacethisequipment.To see

translations of the warnings that appear in this publication, refer to the

Regulatory Compliance

and Safety Information

document that accompanied this device.

Required Tools and Equipment

Installation might require some tools and equipment that are not provided as standard equipment with

the router. Following are the tools and parts required for a typical router installation:

•Number 2 Phillips screwdriver.

•Flat-blade screwdrivers: small, 3/16-in. (0.476 cm) and medium, 1/4-in. (0.625 cm).

•Electrostatic discharge (ESD)-preventive wrist strap.

•Screws to secure the rack-mount brackets to the router.

•Grounding lug with attaching screws.

•Cables for connecting a PC or modem to the router (included).

•Cables for connection to the WAN and LAN ports (dependent on configuration):

–

Ethernet 10BASE-T cable for connection to an Ethernet port (included).

–

Ethernet 100BASE-T cable for connection to a Fast Ethernet port (included).

–

Token Ring lobe cable for connection to the Token Ring port (included).

3-2

Cisco 2600 Series Routers Hardware Installation Guide OL-2171-02

Chapter 3 Installing the Router

Setting Up the Chassis

Note For more information on cable specifications, refer to the online document Cisco Modular Access

Router Cabling Specifications on the Documentation CD-ROM that accompanied your router

package and on Cisco.com. For cable ordering information, see “Obtaining Technical Assistance”.

•Ethernet 10BASE-T hub or PC with a network interface card for connection to the Ethernet (LAN)

port(s).

•Console terminal (an ASCII terminal or a PC running terminal emulation software) configured for

9600 baud, 8 data bits, no parity, and 2 stop bits. A terminal is required unless you are using the

AutoInstall procedure. See the “Connecting the Console Terminal and Modem” section on

page 3-20 for instructions on connecting a console terminal.

•Modem for connection to the auxiliary port for remote administrative access. (Optional)

Setting Up the Chassis

You can set the chassis on a desktop, install it in a rack, or mount it on a wall or other flat surface. Use

the procedure in this section that best meets the needs of your network. The sections are as follows:

•Setting the Chassis on a Desktop, page 3-2

•Mounting the Chassis in a Rack, page 3-4

•Mounting the Chassis on the Wall, page 3-10

Cisco 2600 series routers include the following models:

•Cisco 2610 and Cisco 2610XM

•Cisco 2611 and Cisco 2611XM

•Cisco 2612 and Cisco 2613

•Cisco 2620 and Cisco 2620XM

•Cisco 2621 and Cisco 2621XM

•Cisco 2650 and Cisco 2650XM

•Cisco 2651 and Cisco 2651XM

•Cisco 2691

Setting the Chassis on a Desktop

Before setting the router on a desktop, shelf, or other flat, secure surface, perform the following steps to

install the rubber feet:

Step 1 Locate the rubber feet on the black adhesive strip that shipped with the chassis. (See Figure 3-1.)

3-3

Cisco 2600 Series Routers Hardware Installation Guide

OL-2171-02

Chapter 3 Installing the Router Setting Up the Chassis

Figure 3-1 Identifying the Rubber Feet

Step 2 Place the router upside down on a smooth, flat surface.

Step 3 Peel off the rubber feet from the black adhesive strip and place them adhesive-side down onto the five

round, recessed areas on the bottom of the chassis. (See Figure 3-2 and Figure 3-3.)

Figure 3-2 Rubber Feet Location on Cisco 261x, Cisco 262x, Cisco 26xxXM, and Cisco 265x Series

Routers

Rubber feet (5)

Black adhesive strip

H4796

Fan

H4795

3-4

Cisco 2600 Series Routers Hardware Installation Guide OL-2171-02

Chapter 3 Installing the Router

Setting Up the Chassis

Figure 3-3 Rubber Feet Location on Cisco 2691 Router

Step 4 Place the router right-side up on a flat, smooth, secure surface.

Caution Do not place anything on top of the router that weighs more than 10 lb (4.5 kg). Excessive weight on

top could damage the chassis.

Mounting the Chassis in a Rack

This section describes the procedures for rack-mounting the chassis. Cisco 2600 series routers with a

chassis height of 1 rack-unit (1RU) ship with brackets for use with a 19-inch rack or, if specified in your

order, optional larger brackets for use with a 23- or 24-inch rack. Cisco 2600 series routers with a chassis

height of 2 rack-units (2RU) ship with brackets for use with a 19-inch rack. The brackets are shown in

Figure 3-4 and Figure 3-5.

Warning

To prevent bodily injury when mounting or servicing this unit in a rack, you must take special

precautions to ensure that the system remains stable. To see translations of the warnings that

appear in this publication, refer to the

Regulatory Compliance and Safety Information

document

that accompanied this device. The following guidelines are provided to ensure your safety:

•If the rack contains only one unit, mount the unit at the bottom of the rack.

•If the rack is partially filled, load the rack from the bottom to the top, with the heaviest component

at the bottom of the rack.

72099

Chassis bottom

3-5

Cisco 2600 Series Routers Hardware Installation Guide

OL-2171-02

Chapter 3 Installing the Router Setting Up the Chassis

•If the rack contains stabilizing devices, install the stabilizers before mounting or servicing the unit

in the rack.

Figure 3-4 Brackets for Cisco 261x, Cisco 262x, Cisco 26xxXM, and Cisco 265x Series Routers

Figure 3-5 Brackets for Cisco 2691 Router

Attaching the Brackets to Cisco 261x, Cisco 262x, Cisco 26xxXM, and Cisco 265x Series Routers

To install the chassis in a rack, attach the brackets in one of the following ways:

•With the front panel forward (see Figure 3-6 and Figure 3-7)

•With the rear panel forward (see Figure 3-8 and Figure 3-9)

•In a center-mount rack, with the rear panel forward (see Figure 3-10 through Figure 3-12)

Note Use the screws that came with your router package for attaching the brackets.

Note If you are installing a Cisco 2600 series router in a 19-inch rack with a 17.5-inch opening, orient the

rack-mount brackets so that, when installed, they do not increase the width of the chassis. (See

Figure 3-6.)

If you are installing a Cisco 2600 series router in a 19-inch rack with a 17.75-inch opening or a 23- or

24-inch rack, orient the rack-mount brackets so that, when installed, they increase the width of the

chassis. (See Figure 3-7.)

Bracket for use with a

23-inch or 24-inch rack

Bracket for use

with a 19-inch rack

27711

Narrow bracket for

chassis side opposite fans Wide bracket for

chassis side with fans

Slots for

cable tie

attachment

60289

LEFT

RIGHT

3-6

Cisco 2600 Series Routers Hardware Installation Guide OL-2171-02

Chapter 3 Installing the Router

Setting Up the Chassis

Note The following illustrations show how to connect the bracket to one side of the chassis. The second

bracket connects to the opposite side of the chassis.

Figure 3-6 Bracket Installation—Front Panel Forward (19-Inch Rack with a 17.5-Inch Opening)

Note When installed in a 19-inch rack with a 17.75-inch opening, the Cisco 2600 series routers will

protrude beyond the front of the rack.

Figure 3-7 Bracket Installation—Front Panel Forward (19-Inch Rack with a 17.75-Inch Opening or a

23- or 24-Inch Rack)

62676

Note: The second bracket attaches to the other side of the chassis.

62881

Note: The second bracket attaches

to the other side of the chassis.

Brackets for

19-inch rack Brackets for

23-inch or 24-inch rack

3-7

Cisco 2600 Series Routers Hardware Installation Guide

OL-2171-02

Chapter 3 Installing the Router Setting Up the Chassis

Figure 3-8 Bracket Installation—Rear Panel Forward (19-Inch Rack with a 17.5-Inch Opening)

Figure 3-9 Bracket Installation—Rear Panel Forward (19-Inch Rack with a 17.75-Inch Opening or a

23- or 24-Inch Rack)

72013

Note: The second bracket attaches

to the other side of the chassis.

Brackets for

19-inch rack

110V 60 Hz

1.6A MAX

72014

Note: The second bracket attaches

to the other side of the chassis.

110V 60 Hz

1.6A MAX

Brackets for

19-inch rack Brackets for

23-inch or 24-inch rack

3-8

Cisco 2600 Series Routers Hardware Installation Guide OL-2171-02

Chapter 3 Installing the Router

Setting Up the Chassis

Figure 3-10 Center-Mount Bracket Installation—Rear Panel Forward (19-Inch Rack with a 17.75-Inch

Opening or a 23- or 24-Inch Rack)

Figure 3-11 Center-Mount Bracket Installation—Rear Panel Forward (19-Inch Rack with a 17.5-Inch

Opening or a 23- or 24-Inch Rack)

Figure 3-12 Center-Mount Bracket Installation—Front Panel Forward (19-Inch Rack with a 17.5-Inch

Opening or a 23- or 24-Inch Rack)

72015

Note: The second bracket attaches

to the other side of the chassis.

110V 60 Hz

1.6A MAX

Brackets for

19-inch rack Brackets for

23-inch or 24-inch rack

62983

Note: The second bracket attaches

to the other side of the chassis.

Brackets for

19-inch rack Brackets for

23-inch or 24-inch rack

110V 60 Hz

1.6A MAX

72016

Note: The second bracket attaches

to the other side of the chassis.

Brackets for

19-inch rack Brackets for

23-inch or 24-inch rack

3-9

Cisco 2600 Series Routers Hardware Installation Guide

OL-2171-02

Chapter 3 Installing the Router Setting Up the Chassis

Attaching the Brackets to a Cisco 2691 Router

To install the chassis in a rack, attach the brackets in one of the following ways:

•With the front panel forward (see Figure 3-13.)

•With the rear panel forward (see Figure 3-14.)

•In a center-mount rack (see Figure 3-15 and Figure 3-16.)

Note Use the screws that came with your router package for attaching the brackets.

Figure 3-13 Bracket Installation—Front Panel Forward (19-Inch Rack)

Figure 3-14 Bracket Installation—Rear Panel Forward (19-Inch Rack)

LEFT

Wide bracket

(marked RIGHT)

62103

Narrow bracket

(marked LEFT)

RIGHT

SERIES

RIGHT

Wide bracket

(marked RIGHT)

62109

SEE MANUAL BEFORE INSTALLATION

Narrow bracket

(marked LEFT)

SEE MANUAL BEFORE INSTALLATION

DSU

56K

SEE MANUAL BEFORE INSTALLATION

DSU

56K

LEFT

BANK 4 BANK 3 BANK 2 BANK 1 BANK 0

NM-HDV

VWIC

2MFT-E1

SEE

MANUAL

BEFORE

INSTALLATION

CTRLR E2 CTRLR E1

3-10

Cisco 2600 Series Routers Hardware Installation Guide OL-2171-02

Chapter 3 Installing the Router

Setting Up the Chassis

Figure 3-15 Center-Mount Bracket Installation—Front Panel Forward (19-Inch Rack)

Figure 3-16 Center-Mount Bracket Installation—Rear Panel Forward (19-Inch Rack)

Installing the Router in a Rack

After the brackets are secured to the chassis, you can mount the chassis in a rack. Use the illustrations

in the previous section as a guide to attaching the brackets to the rack.

Note The screws for attaching the brackets to the rack are not included with the router.

Caution Always use two screws to attach each bracket to the rack.

Mounting the Chassis on the Wall

Cisco 2600 series routers with a chassis height of 1RU can be attached to a wall. Mounting a 2RU chassis

to a wall is not recommended and brackets are not provided for mounting to a wall.

LEFT

Wide bracket

(marked RIGHT)

62677

RIGHT

SERIES

Narrow bracket

(marked LEFT)

RIGHT

Wide bracket

(marked RIGHT)

62108

SEE MANUALBEFORE INSTALLATION

Narrow bracket

(marked LEFT)

SEE MANUALBEFORE INSTALLATION

DSU

56K

SEE MANUALBEFORE INSTALLATION

DSU

56K

LEFT

BANK 4 BANK 3 BANK 2 BANK 1 BANK 0

NM-HDV

VWIC

2MFT-E1

SEE

MANUAL

BEFORE

INSTALLATION

CTRLR E2 CTRLR E1

Andere Handbücher für 2600 Series

Inhaltsverzeichnis

Andere Cisco Netzwerk-Router Handbücher

Cisco

Cisco 7200 VXR Series Bedienungsanleitung

Cisco

Cisco RV120W Bedienungsanleitung

Cisco

Cisco RV130 Bedienungsanleitung

Cisco

Cisco E-Series Bedienungsanleitung

Cisco

Cisco 2650 - 2650 Router Handbuch

Cisco

Cisco 700 series Bedienungsanleitung

Cisco

Cisco Linksys WRT54GCV2 Bedienungsanleitung

Cisco

Cisco GRS Bedienungsanleitung

Cisco

Cisco CVR100W Bedienungsanleitung

Cisco

Cisco 1801 Bedienungsanleitung

Cisco

Cisco ASR 5500 Bedienungsanleitung

Cisco

Cisco Linksys E1200 Bedienungsanleitung

Cisco

Cisco Dial NMS Bedienungsanleitung

Cisco

Cisco RV042 - Small Business Dual WAN VPN Router Bedienungsanleitung

Cisco

Cisco IR8340 Kurzanleitung

Cisco

Cisco WRT150N Bedienungsanleitung

Cisco

Cisco 7401 Bedienungsanleitung

Cisco

Cisco 3640 Series Bedienungsanleitung

Cisco

Cisco 2524 - Router - EN Bedienungsanleitung

Cisco

Cisco Performance Routing Engine 5 Bedienungsanleitung

Cisco

Cisco 12010 series Bedienungsanleitung

Cisco

Cisco 4000-M series Stücklistenhandbuch

Cisco

Cisco Catalyst IR1800 Rugged Series Bedienungsanleitung

Cisco

Cisco 809 Kurzanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

LevelOne

LevelOne FBR-1416 Bedienungsanleitung

Dynacord

Dynacord Promatrix 6000 Bedienungsanleitung

Lorex

Lorex F5D8230-4 Bedienungsanleitung