Cisco 8201 Bedienungsanleitung

Replace Chassis Components

•Replace Fan Modules for Cisco 8201 Routers, on page 1

•Replace Power Supply, on page 3

Replace Fan Modules for Cisco 8201 Routers

The fan module is designed to be removed and replaced while the system is operating without presenting an

electrical hazard or damage to the system. Please keep the replacement fan modules ready prior to attempting

this task.

The routers support FAN-1RU-PI (port-side intake airflow) and FAN-1RU-PE (port-side exhaust airflow)

fan modules.

Note

The airflow direction must be the same for all power supply and fan modules in the chassis.

Note

Step 1 To remove a fan module, follow these steps:

a) Press two latches on the fan module and grasp the handle of fan module.

Replace Chassis Components

Figure 1: Cisco 8201 Router —Remove Fans

Latched fan module1

b) As you simultaneously press the latches pull the fan module fully out of the chassis.

Step 2 To install a fan module, follow these steps:

a) Hold the fan module with the LED at the top.

b) Align the fan module to the open fan tray slot in the chassis, and press the module all the way into the slot until the

left and right latches click and are locked on the chassis.

Replace Chassis Components

Replace Fan Modules for Cisco 8201 Routers

If the fan module does not go all the way into the slot, do not force it. Remove the fan module and verify

that it is the correct type for your router and in the correct orientation. To verify the status of fans and the

speed, use the show environment fan command.

Note

c) If the chassis is powered on, listen for the sound of the fans in operation. You should immediately hear them in

operation. If you do not hear them, ensure that the fan module is inserted completely in the chassis.

During the fan module replacement, the other fans adjust their speed to allow for proper initialization of

the new module. When you insert a new fan module, the fans may run at lower or higher speeds for a few

minutes.

Note

d) Verify that the fan module LED is green. If the LED is not green, one or more fans are faulty. If this situation occurs,

contact your customer service representative for replacement parts.

Replace Power Supply

Use this procedure to replace the AC or DC power supply units. Be sure to power down the fixed configuration

PDU (power distribution unit) before removing it from the chassis.

Step 1 If the power supply is connected to a AC or DC circuit, shut off the circuit at the circuit breaker.

Step 2 Disconnect the PSU cable.

Step 3 Press the tab inward to unlatch the PSU, and pull the handle to remove the PSU.

Step 4 Insert the new PSU.

If the PSU does not go all the way into the slot, do not force it. Remove the PSU and verify that it is the correct

type for your router and in the correct orientation.

Note

Step 5 Connect the PSU cable.

Step 6 If the power supply is connected to a DC circuit, turn on the circuit breaker for the DC power source. After replacing the

PSU, verify the power using the show environment power command.

Replace Chassis Components

Replace Power Supply

Figure 2: Cisco 8201 Router —Remove Power Supply

Power supply1

Replace Chassis Components

Replace Power Supply

Inhaltsverzeichnis

Andere Cisco Netzwerk-Router Handbücher

Cisco

Cisco 15310-CL Bedienungsanleitung

Cisco

Cisco 8600 Handbuch

Cisco

Cisco CRS-1 - Carrier Routing System Router Handbuch

Cisco

Cisco SN 5428-2 Anleitung zur Verwendung

Cisco

Cisco OmniPeek NetFlow Analyzer s Bedienungsanleitung

Cisco

Cisco ASR 900 Series Bedienungsanleitung

Cisco

Cisco 2821 - Integrated Services Router Unified Communications... Installationsanleitung

Cisco

Cisco EF4116 Bedienungsanleitung

Cisco

Cisco SFE1000P - Small Business Managed Switch Bedienungsanleitung

Cisco

Cisco 1905 Bedienungsanleitung

Cisco

Cisco cBR 8 Bedienungsanleitung

Cisco

Cisco ASR 903 Bedienungsanleitung

Cisco

Cisco 2524 - Router - EN Bedienungsanleitung

Cisco

Cisco RV160 Bedienungsanleitung

Cisco

Cisco ASR 907 Handbuch

Cisco

Cisco WS-SUP720-3B - Supervisor Engine 720 Bedienungsanleitung

Cisco

Cisco Catalyst 2900 Series XL Bedienungsanleitung

Cisco

Cisco 7200 VXR Series Bedienungsanleitung

Cisco

Cisco 7201 Bedienungsanleitung

Cisco

Cisco RV130 Bedienungsanleitung

Cisco

Cisco Small Business RV215W Bedienungsanleitung

Cisco

Cisco Linksys WRT54GS Original Betriebsanleitung

Cisco

Cisco MWR 1941-DC - 1941 Mobile Wireless Router Bedienungsanleitung

Cisco

Cisco 7246 - uBR Router Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

LevelOne

LevelOne FBR-1416 Bedienungsanleitung

Dynacord

Dynacord Promatrix 6000 Bedienungsanleitung

Lorex

Lorex F5D8230-4 Bedienungsanleitung