Cisco 8608 Bedienungsanleitung

Replace Chassis Components

The images in this chapter are only for representation purposes, unless specified otherwise. The chassis' actual

appearance and size may vary.

Note

Whenever you replace any card, you must always ensure to secure the ejector thumbscrews properly.

Caution

•Replace a Route Processor Card, on page 1

•Replace Modular Port Adapters, on page 6

•Replace a Switch Card, on page 11

•Replace a Fan Spinner, on page 15

•Replace a Fan Module, on page 17

•Replace Power Modules, on page 20

Replace a Route Processor Card

The router supports up to two redundant Route Processor (RP) cards. When two RP cards are installed in the

router, one acts as an active card and the other as the standby card. If the router has only one RP card installed,

a new RP can be installed in the empty RP slot during operation.

• The replacement procedure for the RP cards is only applicable to the standby RP card. You need to

shutdown the router to replace an RP on a single-RP system. When you shutdown the standby RP card,

the router automatically shuts down the standby Switch Card (SC) as both of them belong to the same

operational domain. For example, when you shutdown RP0, the router shuts down the corresponding

SC0. When you shutdown RP1, the router shuts down SC1.

• To replace an active RP card, you must trigger a failover using the redundancy switchover command.

Note

Replace Chassis Components

Statement 1029—Blank Faceplates and Cover Panels

Blank faceplates and cover panels serve three important functions: they prevent exposure to hazardous voltages

and currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other

equipment; and they direct the flow of cooling air through the chassis. Do not operate the system unless all

cards, faceplates, front covers, and rear covers are in place.

Warning

Statement 1034—Backplane Voltage

Hazardous voltage or energy is present on the backplane when the system is operating. Use caution when

servicing

Warning

Before you begin

Before replacing the Route Processor (RP) card, you must perform a graceful shutdown of the card to avoid

disk corruption. Use one of the following procedures to perform graceful shutdown of the card:

• unscrew the captive screws, pull the release latch down, and open ejector lever to trigger auto-shutdown

of the card, and then verify that the Status LED is in Off state.

• use the shutdown location location command in admin EXEC mode to shutdown the card. Then use

the show platform command to verify that the Status LED is in Off state.

Procedure

Step 1 Open the packaging for the new RP card, inspect the card for damage, and verify that the card is the same

type as the other RP cards installed in the chassis.

If the RP card is damaged, alert the Technical Assistance Center (TAC).

Step 2 If you are installing the RP card in an empty slot, remove the blank card that is already in that slot by unscrewing

its captive screw and pulling it out of the slot. Go to Step 4.

Step 3 If you are replacing an RP card that is currently in the chassis, remove the existing card from the chassis by

following these steps:

a) Disconnect the following cables from the card:

• Console cable

• Ethernet Management cable

b) If there are any external drives attached to the card through its USB ports, detach those drives.

c) Perform the graceful shutdown of the RP. Run the shutdown location location command in admin EXEC

mode, which gracefully shuts down RP module to prevent any of the file systems from being corrupted.

d) Verify that the RP Status LED for the slot that you specified turns off. Also, you can verify that the card

is in the powered off state by running the show platform command.

e) Rotate the captive screw, press the latch, and rotate the ejector lever away from the front of the card (see

Callouts 1 and 2 in the following figure).

Replace Chassis Components

Replace a Route Processor Card

The card unseats its connectors from the midplane and moves slightly out of the chassis.

Figure 1: Remove Route Processor Card from Chassis

Release the latch.2Unscrew the captive screw.1

Pull on the lever to slide the card partly out of

the chassis. Release the lever, hold the front of

the card, and pull the card all the way out of the

chassis.

4Rotate the ejector lever away from the card.3

f) Use one hand to hold the front of the card, place your other hand under the card to support its weight, pull

the card out of the chassis, and set it on an antistatic surface or inside an antistatic bag.

Step 4 To install a new card, follow these steps:

a) Pull the middle section of the ejector lever toward the end of the lever and rotate the lever away from the

front of the card.

This action opens the lever so that the card can be fully inserted into the slot.

b) Hold the front of the card with one hand and place your other hand under the card to support its weight.

c) Align the back of the card to the guides in the open route processor slot and slide the card all the way into

the slot (see the following figure).

The card stops when its front is about 0.25 inches (0.6 cm) outside the front of the chassis.

Replace Chassis Components

Replace a Route Processor Card

Figure 2: Install Route Processor Card into Chassis

Press the latch upwards.3Slide the back end of the card into the open

route processor slot.

Rotate the captive screw to secure the route

processor card.

4Rotate the ejector lever towards the card.2

d) Rotate the lever all the way to the front of the chassis until it locks in place with a click.

Ensure that the other end of the lever engages behind the front of the slot so that the card fully seats onto

the connectors on the midplane.

e) Rotate the captive screw to secure the card to the chassis. Tighten the screws to 9.7 in-lbs (1.09 N-m) of

torque.

f) Attach the following cables to the card:

• Console cable—Attach to the Console port.

• Management cable—Attach to the Management Ethernet port.

Reload an RP card by using the reload location location command. Verify that the reloaded

RP card is again in the Operational state by using the show platform command.

To verify the mode of RP card, if it is in standby or active mode, use the show platform

domain command.

Note

Replace Chassis Components

Replace a Route Processor Card

g) Verify that the route processor card LEDs turn on and appear as follows:

• The Status LED is in solid amber color and later turns to solid green color.

Figure 3: Route Processor LEDs

Sync1

Status2

Attention3

Management Activity4

GPS5

Active6

MigratingfromSingleRouteProcessorSystemtoDual-RouteProcessorSystem

The Cisco 8608 router supports a single Route Processor (RP) system and a dual Router Processor system.

This section provides step-by-step instructions for migrating from a single-RP system to a dual-RP system.

Replace Chassis Components

Migrating from Single Route Processor System to Dual-Route Processor System

1. From the SC slot, where you want to install a new SC, remove the fan trays, and then remove the Fan

Spinner. For more information, see Remove a Fan Spinner.

2. In the slot from where you removed the fan spinner, insert the standby Switch Card (SC). For more

information, see Install a Switch Card.

3. After you're done installing the SC, install the fan trays, and then install the RP card. For more information,

see Replace a Route Processor Card.

Migrating from Dual-Route Processor System to Single Route Processor System

This section provides step-by-step instructions for migrating from a dual-RP system to a single-RP system.

1. Remove the fan trays from the standby SC that you want to remove.

2. Remove the standby SC from the slot. For more information, see Remove a Switch Card.

3. Install a Fan Spinner in the slot where you've removed the standby SC. For more information, see Install

a Fan Spinner.

4. After you're done installing the Fan Spinner, install the fan trays. For more information, see Replace a

Fan Module.

Replace Modular Port Adapters

The following sections describe how to remove or install an MPA:

Remove a Modular Port Adapter

Before you begin:

Before replacing the Modular Port Adapter (MPA), you must perform a graceful shutdown of the module to

avoid disk corruption. Use one of the following procedures to perform graceful shutdown of the card:

• unscrew the captive screws, pull the release latch down, and open ejector lever to trigger auto-shutdown

of the card, and then verify that the Status LED is in Off state.

• use the shutdown location location command in admin EXEC mode to shutdown the card. Then use

the show platform command to verify that the Status LED is in Off state.

To remove an MPA, perform the following steps:

1. Ensure the router is in the NSR-ready state. Use the show redundancy command as shown in the following

example:

Router#show redundancy

Thu Jun 1 21:44:12.842 UTC

Redundancy information for node 0/RP0/CPU0:

==========================================

Node 0/RP0/CPU0 is in ACTIVE role

Partner node (0/RP1/CPU0) is in STANDBY role

Standby node in 0/RP1/CPU0 is ready

Standby node in 0/RP1/CPU0 is NSR-ready

Reload and boot info

Replace Chassis Components

Replace Modular Port Adapters

----------------------

RP reloaded Wed May 31 16:03:53 2023: 1 day, 5 hours, 40 minutes ago

Active node booted Wed May 31 16:03:53 2023: 1 day, 5 hours, 40 minutes ago

Standby node boot Wed May 31 16:04:06 2023: 1 day, 5 hours, 40 minutes ago

Standby node last went not ready Wed May 31 16:07:06 2023: 1 day, 5 hours, 37 minutes

ago

Standby node last went ready Wed May 31 16:08:53 2023: 1 day, 5 hours, 35 minutes ago

Standby node last went not NSR-ready Wed May 31 16:06:49 2023: 1 day, 5 hours, 37 minutes

ago

Standby node last went NSR-ready Wed May 31 16:13:26 2023: 1 day, 5 hours, 30 minutes

ago

There have been 0 switch-overs since reload

Active node reload "User initiated chassis reload"

Standby node reload "User initiated chassis reload"

2. Perform the graceful shutdown of the MPA. Run the shutdown location location command in admin

EXEC mode, which gracefully shuts down MPA to prevent any of the file systems from being corrupted.

3. Verify that the MPA Status LED for the slot that you specified turns off. Also, you can verify that the

card is in the powered off state by running the show platform command.

4. To remove the MPA from the chassis, loosen the captive screws (marked as 1 in the image) on the MPA.

5. Press the tab down (marked as 2 in the image).

6. Pull the ejector lever away from the MPA (marked as 3 in the image).

7. Grasp the MPA and pull the MPA from the chassis (marked as 4 in the image). (You have already

disconnected the cables from the MPA.)

Figure 4: Remove an MPA

Press the tab down.2Rotate the captive screw to loosen the MPA.1

Pull the ejector lever away from the MPA.3

Replace Chassis Components

Remove a Modular Port Adapter

8. Verify that the router is in the NSR-ready state. Use the show redundancy command as shown in the

following example:

Router#show redundancy

Thu Jun 1 21:52:36.811 UTC

Redundancy information for node 0/RP0/CPU0:

==========================================

Node 0/RP0/CPU0 is in ACTIVE role

Partner node (0/RP1/CPU0) is in STANDBY role

Standby node in 0/RP1/CPU0 is ready

Standby node in 0/RP1/CPU0 is NSR-ready

Reload and boot info

----------------------

RP reloaded Wed May 31 16:03:53 2023: 1 day, 5 hours, 48 minutes ago

Active node booted Wed May 31 16:03:53 2023: 1 day, 5 hours, 48 minutes ago

Standby node boot Wed May 31 16:04:06 2023: 1 day, 5 hours, 48 minutes ago

Standby node last went not ready Wed May 31 16:07:06 2023: 1 day, 5 hours, 45 minutes

ago

Standby node last went ready Wed May 31 16:08:53 2023: 1 day, 5 hours, 43 minutes ago

Standby node last went not NSR-ready Wed May 31 16:06:49 2023: 1 day, 5 hours, 45 minutes

ago

Standby node last went NSR-ready Wed May 31 16:13:26 2023: 1 day, 5 hours, 39 minutes

ago

There have been 0 switch-overs since reload

Active node reload "User initiated chassis reload"

Standby node reload "User initiated chassis reload"

9. Proceed with installing an MPA.

Install a Modular Port Adapter

This section provides step-by-step instructions for installing a modular port adapter (MPA) in a Cisco 8600

Series router.

After you remove the MPA from the slot, wait for 60 seconds before you reinsert an MPA.

Note

During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly

touch the backplane with your hand or any metal tool, or you could shock yourself. Statement 94

Warning

To install an MPA, perform the following steps:

1. Ensure the router is in the NSR-ready state. Use the show redundancy command as shown in the following

example:

Router#show redundancy

Thu Jun 1 21:44:12.842 UTC

Redundancy information for node 0/RP0/CPU0:

==========================================

Node 0/RP0/CPU0 is in ACTIVE role

Partner node (0/RP1/CPU0) is in STANDBY role

Standby node in 0/RP1/CPU0 is ready

Standby node in 0/RP1/CPU0 is NSR-ready

Replace Chassis Components

Install a Modular Port Adapter

Reload and boot info

----------------------

RP reloaded Wed May 31 16:03:53 2023: 1 day, 5 hours, 40 minutes ago

Active node booted Wed May 31 16:03:53 2023: 1 day, 5 hours, 40 minutes ago

Standby node boot Wed May 31 16:04:06 2023: 1 day, 5 hours, 40 minutes ago

Standby node last went not ready Wed May 31 16:07:06 2023: 1 day, 5 hours, 37 minutes

ago

Standby node last went ready Wed May 31 16:08:53 2023: 1 day, 5 hours, 35 minutes ago

Standby node last went not NSR-ready Wed May 31 16:06:49 2023: 1 day, 5 hours, 37 minutes

ago

Standby node last went NSR-ready Wed May 31 16:13:26 2023: 1 day, 5 hours, 30 minutes

ago

There have been 0 switch-overs since reload

Active node reload "User initiated chassis reload"

Standby node reload "User initiated chassis reload"

2. To insert the MPA, locate the guide rails inside the chassis that hold the MPA in place.

3. Carefully slide the MPA all the way in the chassis until the MPA is firmly seated in the MPA interface

connector. When fully seated, the MPA might be slightly behind the faceplate.

The MPA will slide easily into the slot if it is properly aligned on the tracks. If the MPA does not slide easily,

do NOT force it. Remove the MPA and reposition it, paying close attention to engaging it on the tracks. Push

the MPA inside the slot until you hear a click. Continue to push the MPA further until you hear a second click.

The MPA is fully seated only after the second click is heard.

Note

4. After the MPA is properly seated, pull the ejector lever towards the chassis (marked as 2 in the image).

5. Pull the tab up (marked as 3 in the image).

6. Use a number 2 Phillips screwdriver to tighten the captive screws(marked as 4 in the image) on the MPA.

Figure 5: Install an MPA

Replace Chassis Components

Install a Modular Port Adapter

Pull the ejector lever towards the MPA.2Slide the back end of the MPA into the open

MPA slot.

Rotate the captive screw to tighten the MPA.4Pull the tab up.3

Tighten the captive screws on the MPA within 10 seconds.

Note

Do not over-torque the MPA captive screws when installing the MPA. Tighten the captive screws on the MPA

to a torque of 9.7 in-lbs (1.09 N-m).

Note

7. Verify that after you've installed MPA, the router is in the NSR-ready state. Use the show redundancy

command as shown in the following example:

Router#show redundancy

Thu Jun 1 21:52:36.811 UTC

Redundancy information for node 0/RP0/CPU0:

==========================================

Node 0/RP0/CPU0 is in ACTIVE role

Partner node (0/RP1/CPU0) is in STANDBY role

Standby node in 0/RP1/CPU0 is ready

Standby node in 0/RP1/CPU0 is NSR-ready

Reload and boot info

----------------------

RP reloaded Wed May 31 16:03:53 2023: 1 day, 5 hours, 48 minutes ago

Active node booted Wed May 31 16:03:53 2023: 1 day, 5 hours, 48 minutes ago

Standby node boot Wed May 31 16:04:06 2023: 1 day, 5 hours, 48 minutes ago

Standby node last went not ready Wed May 31 16:07:06 2023: 1 day, 5 hours, 45 minutes

ago

Standby node last went ready Wed May 31 16:08:53 2023: 1 day, 5 hours, 43 minutes ago

Standby node last went not NSR-ready Wed May 31 16:06:49 2023: 1 day, 5 hours, 45 minutes

ago

Standby node last went NSR-ready Wed May 31 16:13:26 2023: 1 day, 5 hours, 39 minutes

ago

There have been 0 switch-overs since reload

Active node reload "User initiated chassis reload"

Standby node reload "User initiated chassis reload"

After you install an MPA, you can use the show interfaces command to verify the traffic on that MPA.

Note

Replace Chassis Components

Install a Modular Port Adapter

Inhaltsverzeichnis

Andere Cisco Netzwerk-Router Handbücher

Cisco

Cisco 12000 - Series Chassis Modular Expansion... Handbuch

Cisco

Cisco 2801 - Integrated Services Router Bedienungsanleitung

Cisco

Cisco ASR 5000 Bedienungs- und Wartungshandbuch

Cisco

Cisco ASR1006-10G-SEC/K9 - ASR 1006 VPN+FW Bundle... Bedienungsanleitung

Cisco

Cisco 1801 Bedienungsanleitung

Cisco

Cisco RV042 - Small Business Dual WAN VPN Router Bedienungsanleitung

Cisco

Cisco Linksys WET610N Bedienungsanleitung

Cisco

Cisco 3800 Series Bedienungsanleitung

Cisco

Cisco 7600 Series Bedienungsanleitung

Cisco

Cisco SGE2000 Bedienungsanleitung

Cisco

Cisco 1700 series Bedienungsanleitung

Cisco

Cisco IOS Router Bedienungsanleitung

Cisco

Cisco OL-4387-02 Bedienungsanleitung

Cisco

Cisco Cisco 760 Series Bedienungsanleitung

Cisco

Cisco ASR 9000 Series Bedienungsanleitung

Cisco

Cisco 761M Bedienungsanleitung

Cisco

Cisco ASR 902U Handbuch

Cisco

Cisco ME-C6524GS-8S Bedienungsanleitung

Cisco

Cisco 12000 - Series Chassis Modular Expansion... Bedienungsanleitung

Cisco

Cisco Linksys EA2700 Bedienungsanleitung

Cisco

Cisco ASR 903 Handbuch

Cisco

Cisco 1760 - VPN Bundle Router Handbuch

Cisco

Cisco 1601-R Bedienungsanleitung

Cisco

Cisco Router Cisco 831 Anleitung zur Verwendung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

LevelOne

LevelOne FBR-1416 Bedienungsanleitung

Dynacord

Dynacord Promatrix 6000 Bedienungsanleitung

Lorex

Lorex F5D8230-4 Bedienungsanleitung