Cisco Linksys SGE2010P Handbuch

ADMIN GUIDE

BUSINESS SERIES

48-port 10/100/1000 Ethernet

Switch

Model: SGE2010/SGE2010P

SGE2010/SGE2010P Administration Guide i

Table of Contents

1Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

What’s in this User Guide? 1

2Getting to Know the SGE2010/SGE2010P . . . . . . . . . . . . . . 2

SGE2010/P Front Panel 2

SGE2010/P Back Panel 3

3Connecting Devices to the SGE2010/SGE2010P . . . . . . . . . . . 4

Sample Network Configuration 4

Maximum Cabling Distances 4

Before You Install the Switch... 5

Placement Options 5

Desktop Placement 5

Rack-Mount Placement 6

Wall-Mount Placement 7

Connecting the Cables 7

4Using the Console . . . . . . . . . . . . . . . . . . . . . . . . . 9

Connecting to Your Switch with HyperTerminal 9

Connecting to the Switch with Telnet 12

Logging On to the Console 12

Selecting Menu Options and Actions 12

Using the Switch Main Menu 13

System Configuration 13

System Information 14

Management Settings 16

Username & Password Settings 21

Security Settings 22

VLAN Management 25

IP Configuration 26

File Management 40

Restore System Default Settings 43

Reset to Factory Settings 43

Reboot System 43

Stack Configuration 44

Port Status 44

SGE2010/SGE2010P Administration Guide ii

Table of Contents

Port Status 45

PoE Status 45

Port Configuration 46

Port Settings 46

PoE Settings 47

System Mode (Layer 2 / Layer 3) Selection 48

Help 49

Logout 50

5Web Utility Configuration . . . . . . . . . . . . . . . . . . . . 51

Connecting to the Switch with the Web-Based Utility 51

Using Menus in the Web-Based Utility 51

Viewing On-line Help 52

AContacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

US/Canada Contacts 53

BCustomer Site Survey. . . . . . . . . . . . . . . . . . . . . . . 54

CWarranty Information . . . . . . . . . . . . . . . . . . . . . . 56

Limited Warranty 56

Exclusions and Limitations 56

Obtaining Warranty Service 57

Technical Support 57

DFederal Communication Commission Interference Statement . . 58

Industry Canada Statement 58

EC Declaration of Conformity (Europe) 58

ESpecifications . . . . . . . . . . . . . . . . . . . . . . . . . . 59

SGE2010/SGE2010P Administration Guide 1

What’s in this User Guide?

Introduction

Welcome

Thank you for choosing a Linksys Switch. This Switch will allow you to quickly and economically

expand your Linksys system.

This new Linksys rack mount Switch delivers non-blocking, wire speed switching for your

network clients, plus multiple options for connecting to your network backbone. Forty eight

ports wire up your workstations or connect to other Linksys switches or devices.

The Switch features monitoring and configuration via your web browser, making it easy to

manage your Switch. Or if you prefer, you can use the console interface to configure the Switch.

Use the instructions in this guide to help you connect the switch, set it up, and configure it to

bridge your different networks. These instructions should be all you need to get the most out of

the Switch.

What’s in this User Guide?

This user guide covers the steps for setting up and using the Switch.

•Chapter 2, "Getting to Know the SGE2010/SGE2010P"

This chapter describes the ports, LEDs, and other features on the front and back panels of

the switch.

•Chapter 3, "Connecting Devices to the SGE2010/SGE2010P"

This chapter explains how to physically connect your network devices to the switch.

•Chapter 4, "Using the Console"

This chapter describes the use of the switch console, which allows you to perform basic

configuration of the switch.

•Chapter 5, "Web Utility Configuration "

This chapter provides an introduction to the features of the web-based configuration utility.

•Appendix A, "Contacts"

•Appendix B, "Customer Site Survey"

•Appendix C, "Warranty Information"

•Appendix D, "Federal Communication Commission Interference Statement"

•Appendix E, "Specifications"

SGE2010/SGE2010P Administration Guide 2

Getting to Know the SGE2010/SGE2010P

This chapter describes the ports, LEDs, and other features on the front and back panels of the

switch.

The SGE2010 and SGE2010P are 48-port, layer-2 Ethernet switches that affordably expand the

capability of the Linksys system. These two versions are functionally identical except the

SGE2010P model offers Power-over-Ethernet (PoE) which can be used to supply power to

various Linksys products over Ethernet cable.

SGE2010/P Front Panel

Feature Description

Reset The Switch can be reset by inserting a pin or paper clip into the RESET

opening.

CAUTION: If the RESET switch is pressed for more than 10 seconds, the

Switch will reset to its default settings. All customized user settings will be

lost.

LEDs The Switch uses Light Emitting Diodes (LEDs) to indicate the status of

numerous functions. These functions are listed below.

PWR A green PWR LED lights up to indicate that the Switch is powered on.

FAN A green FAN LED lights up to indicate that the cooling fan is operating

properly. A blinking red FAN LED indicates that the cooling fan has failed.

RPS A green RPS LED lights up to indicate that RPS is connected and operating

properly. A blinking red RPS LED indicates an RPS fault.

MST A green MST LED indicates that this Switch is a stack master.

Stack ID A green Stack ID LED indicates that this Switch is stacked and the

corresponding number indicates its stack ID.

Act/Link The green Act/Link LEDs light up to indicate a functional network link

through the corresponding port with an attached device. The Act

(Activity) LEDs flash to indicate that the Switch is actively sending or

receiving data over that port.

Speed On the SGE2010, a green Speed LED indicates that the port is linked to a

100Mbps device.

PoE On the SGE2010P, a green PoE LED indicates that PoE is active on that port.

SGE2010/SGE2010P Administration Guide 3

Getting to Know the SGE2010/SGE2010P

SGE2010/P Back Panel

1-48 The Switch is equipped with 48 auto-sensing, Ethernet (802.3) network

ports, which use RJ-45 connectors. The Fast Ethernet ports support

network speeds of 10Mbps, 100Mbps, or 1000Mbps. They can operate in

half and full-duplex modes. Auto-sensing technology enables each port to

automatically detect the speed of the device connected to it, and adjust

its speed and duplex accordingly.

The switch can deliver a maximum of 15.4W to a PoE port. With regular AC

power supply, there is 360W available to all PoE ports, and 280W available

with redundant power supply.

Ports 45, 46, 47 and 48 are shared with miniGBIC1, miniGBIC2, miniGBIC3,

and miniGBIC4, respectively.

NOTE: A switch is in stacking mode by default. In stacking mode, ports 24

and 48 are reserved for use as stacking ports. For more information

about stacking, refer to the SFE2010/SGE2010 Reference Guide.

miniGBIC1-4 The switch provides four mini-GBIC ports. The mini-GBIC (gigabit interface

converter) port is a connection point for a mini-GBIC expansion module,

so the Switch can be uplinked via fiber to another switch. Each mini-GBIC

port provides a link to a high-speed network segment or individual

workstation at speeds of up to 1000Mbps.

Use the Linksys MGBT1, MGBSX1, or MGBLH1 mini-GBIC modules with the

switch. The MGBSX1 and the MGBLH1 require fiber cabling with LC

connectors, while the MGBT1 requires a Category 5e Ethernet cable with

an RJ-45 connector.

NOTE: If shared ports are both connected, then the miniGBIC port has

priority.

Feature Description

Power The Power port is where you will connect the power cord.

Console The Console port is where you can connect a serial cable to a PC’s serial

port for configuration using your PC’s HyperTerminal program. Refer to

Chapter 4: Using the Console Interface for Configuration for more

information.

RPS Redundant Power Supply (Linksys RPS1000)

Feature Description

SGE2010/SGE2010P Administration Guide 4

Sample Network Configuration

Connecting Devices to the SGE2010/SGE2010P

Connecting Devices to the SGE2010/

SGE2010P

This chapter explains how to physically connect your network devices to the switch.

•”Sample Network Configuration,” on page 4

•”Maximum Cabling Distances,” on page 4

•”Before You Install the Switch... ,” on page 5

•”Placement Options,” on page 5

•”Connecting the Cables,” on page 7

Sample Network Configuration

For an example of a possible network configuration, see the application diagrams shown

below.

Maximum Cabling Distances

When you connect your network devices, make sure you don’t exceed the maximum cabling

distances, which are listed in the following table:

*A hub refers to any type of 100Mbps hub, including regular hubs and stackable hubs. A

10Mbps hub connected to another 10Mbps hub can span up to 100 meters (328 feet).

From To Maximum Distance

Switch Switch or Hub* 100 meters (328 feet)

Hub Hub 5 meters (16.4 feet)

Switch or Hub Computer 100 meters (328 feet)

SGE2010/SGE2010P Administration Guide 5

Before You Install the Switch...

Connecting Devices to the SGE2010/SGE2010P

Before You Install the Switch...

When you choose a location for the switch, observe the following guidelines:

• Make sure that the switch will be accessible and that the cables can be easily connected.

• Keep cabling away from sources of electrical noise, power lines, and fluorescent lighting

fixtures.

• Position the switch away from water and moisture sources.

• To ensure adequate air flow around the switch, be sure to provide a minimum clearance of

two inches (50 mm).

• Connect the supplied power cord to the switch’s power port, and plug the other end into an

electrical outlet.

CAUTION: Make sure you use the power cord that is supplied with the switch. Use of a

different power cord could damage the switch.

Placement Options

Before connecting cables to the Ethernet switch, first you will physically install the Ethernet

switch. Either set the Ethernet switch on its four rubber feet for desktop placement, mount it in

a standard-sized, 19-inch wide for rack-mount placement, or mount it on a wall with the wall-

mount brackets provided.

NOTE: The four supplied mounting brackets can be used for either wall mount or rack

mount installations.

Desktop Placement

1. Attach the rubber feet to the recessed areas on the bottom of the Ethernet switch.

2. Place the Ethernet switch on a desktop near an AC power source.

SGE2010/SGE2010P Administration Guide 6

Placement Options

Connecting Devices to the SGE2010/SGE2010P

CAUTION: Keep enough ventilation space for the Ethernet switch so it does not exceed the

environmental restrictions mentioned in the specifications.

Rack-Mount Placement

To mount the Ethernet switch in any standard-sized, 19-inch wide, (each Ethernet switch

requires 1RU of space in the rack), follow these instructions:

1. Remove the four front screws on one side of the Ethernet switch. Retain the screws for re-

installation.

2. Place one of the supplied spacers on the side of the Ethernet switch so the four holes align

to the screw holes.

3. Place a rack mount bracket next to the spacer and reinstall the four screws (removed in step

1).

4. Repeat steps 2 through 3 for the other side of the Ethernet switch.

5. Attach the Ethernet switch to the rack using the supplied screws.

SGE2010/SGE2010P Administration Guide 7

Connecting the Cables

Connecting Devices to the SGE2010/SGE2010P

Wall-Mount Placement

1. On one of the side corners, remove the four front screws on of the Ethernet switch. Retain

the screws for re-installation.

NOTE: The Ethernet switch, shown below, is mounted with the ports located on top. When

the switch is mounted to a wall, the ports can be oriented in any direction.

2. Place one of the supplied spacers on the side of the Ethernet switch so the four holes align

to the screw holes.

3. Place a rack mount bracket next to the spacer and reinstall the four screws (removed in step

1). The wall mount brackets should point towards the bottom of the Ethernet switch.

4. Repeat steps 1 through 3 for the other corners of the Ethernet switch.

5. Attach the Ethernet switch to a wall with appropriate screws (not supplied).

CAUTION: Ensure that the Ethernet switch is securely attached to the wall.

Connecting the Cables

To connect network devices to the Ethernet switch, follow these instructions:

1. For 10/100Mbps devices, connect a Category 5 Ethernet network cable to one of the

numbered ports on the Ethernet switch. For a 1000Mbps device, connect a Category 5e

Ethernet network cable to one of the uplink ports on the Ethernet switch.

NOTE: If connecting an Ethernet switch to an SVR3000 router, connect it to a Cascade port

on the SVR3000.

2. Connect the other end to a PC or other network device.

3. Repeat steps 2 and 3 to connect additional devices.

4. If you are using the mini-GBIC port, then insert the mini-GBIC module to the mini-GBIC port.

For detailed instructions, refer to the documentation supplied with the mini-GBIC module.

Andere Handbücher für Linksys SGE2010P

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cisco Netzwerk-Router Handbücher

Cisco

Cisco 761M Bedienungsanleitung

Cisco

Cisco Internet Router Cisco 12404 Bedienerhandbuch

Cisco

Cisco 7603 - Modular Expansion Base Bedienungsanleitung

Cisco

Cisco uBR10012 Universal Broadband Router... Bedienungsanleitung

Cisco

Cisco RV160 Bedienungsanleitung

Cisco

Cisco 2654T6 Bedienungsanleitung

Cisco

Cisco CISCO7201 Bedienerhandbuch

Cisco

Cisco 2821 - Integrated Services Router Unified Communications... Installationsanleitung

Cisco

Cisco ASR-920-12CZ-A Bedienungsanleitung

Cisco

Cisco 2600 Series Handbuch

Cisco

Cisco 2500 Series Bedienerhandbuch

Cisco

Cisco 7000 and 7507 LED Board MAS-7KLED Leitfaden

Cisco

Cisco Nexus 9000 Series Bedienungsanleitung

Cisco

Cisco RV160W Bedienungsanleitung

Cisco

Cisco CRM3 Bedienungsanleitung

Cisco

Cisco 2811 - Voice Security Bundle Router Bedienungsanleitung

Cisco

Cisco WRT300N Bedienungsanleitung

Cisco

Cisco LinkSys RTP300 Original Betriebsanleitung

Cisco

Cisco Nexus 7000 Series Bedienungsanleitung

Cisco

Cisco RV082 - Small Business VPN Router Bedienungsanleitung

Cisco

Cisco 811 Bedienungsanleitung

Cisco

Cisco ASR 9000 Series Bedienungsanleitung

Cisco

Cisco Firepower 1120 Bedienungsanleitung

Cisco

Cisco RV345 Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

LevelOne

LevelOne FBR-1416 Bedienungsanleitung

Dynacord

Dynacord Promatrix 6000 Bedienungsanleitung

Lorex

Lorex F5D8230-4 Bedienungsanleitung