Cisco Meraki MV63 Bedienungsanleitung

MV63 Installation Guide

MV63 Series Overview

The Cisco Meraki MV63 series are network cameras that are exceptionally simple to deploy and configure due to their integration into the Meraki Dashboard and

cloud-augmented edge storage. The MV family eliminates complex and costly servers and video recorders required by traditional solutions, removing the

limitations typically placed on video surveillance deployments.

Package Contents:

In addition to the MV camera, the following are provided:

Unit

MV63-HW

MV63X-HW

Mounting Equipment

1 x T10 Torx key

2 x desiccant pack

1 x base mount plate small

1x base mount plate large

1x Decorative cover

1 x conduit adapter

MV63 series does not ship with mounting screws and anchors as an included accessory in the packaging content.

Screw Recommendation:

Powering the MV63 Series

The MV63 features a 1000BASE-TX Ethernet port and requires 802.3at PoE+ minimally for operation. Route the Ethernet cable from an active port on a PoE

switch or injector.

Note: Power over Ethernet supports a maximum cable length of 300 ft (100 m).

Pre-Install Preparation

You should complete the following steps before going on-site to perform an installation:

Configure Your Network in the Dashboard

The following is a brief overview of the steps required to add an MV63 series camera to your network. For detailed instructions about creating, configuring and

managing Meraki Camera networks, refer to the online documentation (https://documentation.meraki.com/MV).

1. Login to http://dashboard.meraki.com. If this is your ﬁrst time, create a new account.

2. Find the network to which you plan to add your cameras or create a new network.

3. Add your cameras to your network. You will need your Meraki order number (found on your invoice) or the serial number of each camera, which looks

like Qxxx-xxxx-xxxx and is found on the bottom of the unit.

4. Verify that the camera is now listed under Cameras > Monitor > Cameras.

Check and Configure Firewall Settings

If a ﬁrewall is in place, it must allow outgoing connections on particular ports to IP addresses. The most current list of outbound ports and IP addresses for your

organization can be found under Help>Firewall Info on the dashboard.

DNS Configuration Best practices for LAN Streaming

Each camera will generate a unique domain name for secured direct streaming functionality. These domain names resolve an A record for the private IP address

of the camera. Any public recursive DNS server will resolve this domain.

If utilizing an on-site DNS server, please whitelist *.devices.meraki.direct or configure a conditional forwarder so that local domains are not appended to

*.devices.meraki.direct and that these domain requests are forwarded to Google public DNS.

•Type: Self-Tapping Screw

•Size: M4

•Length: Minimum 25mm

•Screw head diameter: Maximum 10mm

•Driver Type: ANY (eg: Philips)

•Head Type: ANY (Eg: Pan Head)

•Build Material: Stainless Steel

Note: The insertion diameter of the anchor should be smaller than that of the screw, and the length of the anchor should be longer than that of the

screw. The appropriate anchor should be selected based on the structure that it will be installed on, such as concrete, brick, wood, drywall, etc.

Assigning IP Addresses

Currently, the MV63 series camera does not support static IP assignment. MV63 units must be added to a subnet that uses DHCP and has available DHCP

addresses to operate correctly.

Installation Instructions

Note: During first-time setup, the MV93 series will automatically update to the latest stable firmware. Some features may be unavailable until this automatic

update is completed. This process may take up to 5 minutes to enable whole disk encryption. The state of this process can be monitored by referencing the MV

LED Status.

Mounting Instructions

For most mounting scenarios, the MV63 wall mount provides a quick, simple, and flexible means for mounting your device. The installation should be done in a

few simple steps:

Note: Leave the protective plastic cover on the optical dome throughout the installation process to prevent any damage to the dome. The protective cover should

be removed once the installation is completed.

1. Carefully loosen all four Torx head security screws and remove the optical dome from the base. A tether cable is attached to the optical dome and camera

base to simplify installation. Remove the desiccant pack included in the camera during product shipment and replace it with the provided 2x spare desiccant

pack. This is important to prevent moisture from accumulating within the sealed optical dome.

Microphone Cut-off Switch:

The MV63 Series has a new microphone cut-off switch at the camera's base. This switch can be used to disable audio and override the Dashboard Audio

Settings for an added layer of security. If the regulations require disabling audio or Dashboard control for Audio enablement needs to be disabled, the

microphone cut-off switch can be leveraged and set to Disabled.

Note: If the microphone switch is disabled and the camera is mounted, toggling the switch back ON would require accessing the camera's base.

1. Use the template to determine mounting hole locations for wall mounting before screwing in the base mount plate. Peel backing from the mounting template to

stick on the wall. Use template holes marked with the letter “A” for standard wall mounting. Screw the base mount plate onto the wall in pre-determined locations

using the provided wall screws.

2. Follow this in-depth cable gland assembly guide to connect the PoE cable to the camera cable gland and ensure the seal is water-tight. This step is very

important and may damage the camera if done improperly.

Note: If installing external conduit terminated at the camera, ensure the camera conduit adapter and terminal adapter are pulled over the camera pigtail before

making the connection to avoid the risk of water damage leading to hardware failure and warranty void.

3. If using a conduit adapter, attach the terminal adapter to the conduit adapter. Route the conduit over the water-tight cable gland assembly and terminate at

the terminal adapter. Ensure the camera conduit adapter is securely placed on the base mount plate as pictured.

Installing the conduit box to MV63 series: (optional)

4. MV63 series comes with two base mount plates, a small plate and a large plate. The functionality of both plates is identical. Please refer to the guidelines

below on using the base plate mounting to any surface or on top of a mounting accessory.

MV63 Mount using small base plate:

•Mount the small base plate onto the wall surface using the paper template provided.

•Use 3x Wall anchor and screws to fix the base plate to the wall.

•The MV63 Series cameras have a button to engage the locking mechanism. Press the button while aligning the MV63 series to the small base plate.

Inhaltsverzeichnis

Andere Cisco Sicherheitskamera Handbücher

Cisco

Cisco CIVS-IPC-5010 Bedienungsanleitung

Cisco

Cisco Small Business VC220 Bedienungsanleitung

Cisco

Cisco 6020 Bedienungs- und Sicherheitshinweise

Cisco

Cisco 3530 Bedienungsanleitung

Cisco

Cisco 7030E Bedienungsanleitung

Cisco

Cisco 253 Series Bedienungsanleitung

Cisco

Cisco Nexus 5010 Bedienungsanleitung

Cisco

Cisco Nexus 5010 Bedienungsanleitung

Cisco

Cisco WVC210 - Small Business Wireless-G PTZ Internet Video... Bedienungsanleitung

Cisco

Cisco Meraki MV32 Bedienungsanleitung

Cisco

Cisco PVC2300 - Small Business Internet Video... Bedienungsanleitung

Cisco

Cisco Meraki MV12 Bedienungsanleitung

Cisco

Cisco TelePresence MX700 Bedienungsanleitung

Cisco

Cisco 6020 Bedienungsanleitung

Cisco

Cisco 3421V Bedienungsanleitung

Cisco

Cisco Small Business VC220 Bedienungsanleitung

Cisco

Cisco Wireless Service Module 2 Bedienungsanleitung

Cisco

Cisco 4300E Bedienungsanleitung

Cisco

Cisco 4300 Bedienungsanleitung

Cisco

Cisco WVC200 - Wireless-G PTZ Internet Camera Bedienungsanleitung

Cisco

Cisco CIVS-IPC-2611 Bedienungsanleitung

Cisco

Cisco PVC300 - Small Business Pan Tilt Optical Zoom Internet Camera... Bedienungsanleitung

Cisco

Cisco WVC210 - Small Business Wireless-G PTZ Internet Video... Bedienungsanleitung

Cisco

Cisco WVC2300 - Small Business Wireless-G Internet Video... Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung