Cisco ISA550 Bedienungsanleitung

Quick Start Guide

Cisco Small Business

ISA500 Series Integrated Security Appliances

(ISA550, ISA550W, ISA570, ISA570W)

Package Contents

•ISA500 Series Integrated Security Appliance

•Two Wi-Fi Antennas (for ISA550W and ISA570W only)

•Rack Mounting and Desktop Placement Kit

•Power Cord and Adapter

•RJ-45 Ethernet Cable

•Quick Start Guide

•Product CD

2 Cisco ISA500 Series Integrated Security Appliances Quick Start Guide

Welcome

Thank you for choosing the Cisco ISA500 Series Integrated Security

Appliance. This guide describes how to physically install the device and

how to launch the ISA500 Series Configuration Utility to configure it.

Before You Begin

Before you begin the installation, make sure that you have the following:

•An active Internet account.

•Mounting hardware and related tools. The mounting kit included with

the device contains four rubber feet for desktop placement, two

rack-mount brackets, two silicon rubber spacers, eight M3 screws, four

M5 screws, and four washers for rack mounting. Instructions are

provided for wall mounting, but the wall mounting hardware is

user-supplied.

•RJ-45 Ethernet cables (Category 5E or higher) for connecting

computers, WAN and LAN interfaces, or other devices.

•A computer with Microsoft Internet Explorer 8 or 9, or Mozilla Firefox

3.6.x, 5, or 6 for using the web-based device Configuration Utility.

Default Settings

To restore the factory defaults, choose one of the following actions:

•Press and hold the RESET button on the back panel of the unit for more

than 3 seconds while the unit is powered on and the POWER/SYS light

is solid green.

•Or launch the Configuration Utility and login. Click Device Management

> Reboot/Reset in the left hand navigation pane. In the Reset Device

area, click Reset to Factory Defaults.

Parameter Default Value

Username cisco

Password cisco

LAN IP 192.168.75.1

DHCP Range 192.168.75.100 to 200

Cisco ISA500 Series Integrated Security Appliances Quick Start Guide 3

Getting to Know the Cisco ISA500 Series

Integrated Security Appliances

This section lists the available model numbers to help you become familiar

with your security appliance, and shows the front panel and back panel of

the unit.

Product Models

NOTE Any configurable port can be configured to be a WAN, DMZ, or LAN

port. Only one configurable port can be configured as a WAN port at a

time. Up to 4 configurable ports can be configured as DMZ ports.

Front Panel

ISA550 Front Panel

ISA550W Front Panel

Model Description Configuration

ISA550 Cisco ISA550 Integrated

Security Appliance

1 WAN port, 2 LAN ports, 4 configurable

ports, and 1 USB 2.0 port

ISA550W Cisco ISA550 Integrated

Security Appliance with

Wi-Fi

1 WAN port, 2 LAN ports, 4 configurable

ports, 1 USB 2.0 port, and 802.11b/g/n

ISA570 Cisco ISA570 Integrated

Security Appliance

1 WAN port, 4 LAN ports, 5 configurable

ports, and 1 USB 2.0 port

ISA570W Cisco ISA570 Integrated

Security Appliance with

Wi-Fi

1 WAN port, 4 LAN ports, 5 configurable

ports, 1 USB 2.0 port, and 802.11b/g/n

282351

Small Business

VPN USB WAN LAN CONFIGURABLEPOWER/SYS

SPEED

LINK /ACT

234567

ISA550 Cisco

281983

Small Business

VPN USB WAN LAN CONFIGURABLEPOWER/SYS

SPEED

LINK /ACT

234567

WLAN

ISA550W Cisco

4 Cisco ISA500 Series Integrated Security Appliances Quick Start Guide

ISA570 Front Panel

ISA570W Front Panel

Front Panel Lights

The following table describes the lights on the front panel of the security

appliance. These lights are used for monitoring system activity.

Light Description

POWER/SYS Indicates the power and system status.

•Solid green when the system is powered on and is

operating normally.

•Flashes green when the system is booting.

•Solid amber when the system has a booting problem, a

device error occurs, or the system has a problem.

VPN Indicates the site-to-site VPN connection status.

•Solid green when there are active site-to-site VPN

connections.

•Flashes green when attempting to establish a site-to-site

VPN tunnel.

•Flashes amber when the system is experiencing problems

setting up a site-to-site VPN connection and there is no

VPN connection.

USB Indicates the USB device status.

•Solid green when a USB device is detected and is

operating normally.

•Flashes green when the USB device is transmitting and

receiving data.

WLAN

(ISA550W and

ISA570W only)

Indicates the WLAN status.

•Solid green when the WLAN is up.

•Flashes green when the WLAN is transmitting and

receiving data.

Small Business

VPN USB WAN LAN CONFIGURABLEPOWER/SYS

SPEED

LINK /ACT

910

2345678

282350

ISA570 Cisco

Small Business

VPN USB WAN LAN CONFIGURABLEPOWER/SYS

SPEED

LINK /ACT

910

2345678

WLAN

281980

ISA570W Cisco

Cisco ISA500 Series Integrated Security Appliances Quick Start Guide 5

Back Panel

The back panel is where you connect the network devices. The ports on

the back panel vary depending on the model.

ISA550 and ISA550W Back Panel

ISA570 and ISA570W Back Panel

SPEED Indicates the traffic rate of the associated port.

•Off when the traffic rate is 10 or 100 Mbps.

•Solid green when the traffic rate is 1000 Mbps.

LINK/ACT Indicates that a connection is being made through the port.

•Solid green when the link is up.

•Flashes green when the port is transmitting and receiving

data.

Light Description

281984

ANT02ANT01

RESET

OPOWER

12VDC

CONFIGURABLE

LAN

WAN

ANT01 ANT02

Reset

Button

Power

Switch

Power

Connector

WAN

Port

USB

Port Configurable

Ports

LAN

Ports

281981

RESET

ANT02ANT01

8910

WAN

CONFIGURABLE POWER

12VDC

LAN

ANT01 ANT02

Reset

Button

Power

Switch

Power

Connector

WAN

Port

USB

Port Configurable

Ports

LAN

Ports

6 Cisco ISA500 Series Integrated Security Appliances Quick Start Guide

Back Panel Descriptions

Mounting the Cisco ISA500 Series

Integrated Security Appliances

You can place your security appliance on a desktop, mount it on a wall, or

mount it in a rack.

Placement Tips

• Ambient Temperature: To prevent the security appliance from

overheating, do not operate it in an area that exceeds an ambient

temperature of 104°F (40°C).

•AirFlow:Be sure that there is adequate air flow around the security

appliance.

Feature Description

ANT01/ANT02 Threaded connectors for the antennas (for ISA550W and

ISA570W only).

USB Port Connects the unit to a USB device. You can use a USB

device to save and restore system configuration, or to

upgrade the firmware.

Configurable

Ports

Can be set to operate as WAN, LAN, or DMZ ports. The

ISA550 and ISA550W have 4 configurable ports. The

ISA570 and ISA570W have 5 configurable ports.

NOTE Only one configurable port can be configured as a

WAN port at a time. Up to 4 configurable ports can be

configured as DMZ ports.

LAN Ports Connects PCs and other network appliances to the unit.The

ISA550 and ISA550W have 2 dedicated LAN ports. The

ISA570 and ISA570W have 4 dedicated LAN ports.

WAN Port Connects the unit to a DSL or cable modem, or other WAN

connectivity device.

RESET Button To reboot the unit, push and release the RESET button for

less than 3 seconds.

To restore the unit to its factory default settings, push and

hold the RESET button for a minimum of 3 seconds while

the unit is powered on. The POWER/SYS light will flash

green when the system is rebooting.

Power Switch Powers the unit on or off.

Power Connector Connects the unit to power using the supplied power cord

and adapter.

Cisco ISA500 Series Integrated Security Appliances Quick Start Guide 7

• Mechanical Loading: Be sure that the security appliance is level and

stable to avoid any hazardous conditions.

To place your security appliance on a desktop, install the supplied four

rubber feet on the bottom of the security appliance. Place the security

appliance on a flat surface.

Wall Mounting

The wall mounting hardware is user-supplied. We recommend that you use

the following mounting screws to install your security appliance to the wall.

The wall-mounting features on the bottom of the unit allow the front of the

unit to face either upward or downward.

WARNING Insecure mounting might damage the device or cause injury.

Cisco is not responsible for damages incurred by improper

wall-mounting.

STEP 1Determine where you want to mount the security appliance. Verify

that the surface is smooth, flat, dry, and sturdy.

STEP 2Secure two M3 x 0.63 inch (16 mm) pan head wood screws, with

anchors, into the wall 9.21 inches (234 mm) apart horizontally.

Leave about 1/8 inch (3 to 4 mm) of the screw threads beneath the

screw head exposed.

STEP 3Place the wall-mount slots over the screws and slide the unit down

until the screws fit snugly into the wall-mount slots.

1 8 mm/0.32 in 2 25 mm/0.98 in 3 6.5 mm/0.26 in 4 18.6 mm/0.73 in

196243

8 Cisco ISA500 Series Integrated Security Appliances Quick Start Guide

Rack Mounting

You can mount the security appliance in any standard size, 19-inch (about

48 cm) wide rack. The security appliance requires 1 rack unit (RU) of

space, which is 1.75 inches (44.45 mm) high. The rack-mounting kit is

included with the unit.

CAUTION Do not overload the power outlet or circuit when installing

multiple devices in a rack.

STEP 1Place one of the supplied silicon rubber spacers on the side of the

security appliance so that the four holes align to the screw holes.

Place the rack mount bracket next to the silicon rubber spacer and

install the M3 screws.

STEP 2Install the security appliance into a standard rack as shown below.

Place the washers on the brackets so that the holes align to the

screw holes and then install the M5 screws.

Connecting the Cisco ISA500 Series

Integrated Security Appliances

STEP 1If you are installing the ISA550W or ISA570W, screw each antenna

onto a threaded connector on the back panel. Orient each antenna

to point upward.

STEP 2Connect the security appliance to power using the supplied

power cord and adapter. Make sure that the power switch is

turned off.

281985

Step 1 Step 2

Cisco ISA500 Series Integrated Security Appliances Quick Start Guide 9

STEP 3For a DSL or cable modem, or other WAN connectivity devices,

connect an Ethernet network cable from the device to the WAN

port on the back panel. Cisco strongly recommends using

Category 5E or better cable.

STEP 4(Optional) For network devices, connect an Ethernet network cable

from the network device to an available LAN port on the back panel.

STEP 5Power on the connected devices.

STEP 6Power on the security appliance. The lights on the front panel for

all connected ports light up to show active connections.

A sample configuration is illustrated below.

Getting Started with the Configuration

You can log in to the ISA500 Series Configuration Utility and complete the

initial configuration by using the Setup Wizard; follow these steps:

STEP 1Connect a computer to an available LAN port on the back panel of

the security appliance.

Your PC will become a DHCP client of the security appliance and

will receive an IP address in the 192.168.75.x range.

STEP 2Start a web browser. In the Address bar, enter the default LAN IP

address of the security appliance: 192.168.75.1.

STEP 3When the login page opens, enter the username and password.

The default username is cisco. The default password is cisco.

Usernames and passwords are case sensitive.

281982

RESET

ANT02ANT01

8910

WAN

CONFIGURABLE POWER

12VDC

LAN

Internet

Access

Device

Public

Web Server Power

Network

Devices

10 Cisco ISA500 Series Integrated Security Appliances Quick Start Guide

STEP 4Click Login.

For security purposes, you must change the default password of

the default administrator account.

STEP 5Enter the new administrator password and click OK.

The Setup Wizard will now launch.

STEP 6Follow the on-screen prompts to complete the initial configuration.

Suggested Next Steps

Congratulations, you are now ready to start using your security appliance.

You may want to configure some of the following items to secure your

network:

•Upgrade your firmware to the latest version.

•Configure the VLANs, DMZs, and WLANs.

•Configure the zones.

•Configure the WAN redundancy if you have two ISP links.

•Configure the zone-based firewall.

•Configure the UTM services such as Intrusion Prevention (IPS),

Anti-Virus, Application Control, Spam Filter, Web URL Filtering, and Web

Reputation.

•Configure the VPNs for site-to-site and remote secure access.

•Configure the WAN, LAN, and Wireless QoS settings.

To configure these features, you can use the wizards or menus in the left

navigation pane of the Configuration Utility. For complete details, see the

Cisco ISA500 Series Integrated Security Appliances Administration Guide

at: www.cisco.com/go/isa500resources.

Andere Handbücher für ISA550

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cisco Sicherheitssystem Handbücher

Cisco

Cisco PIX 501 - Security Appliance Bedienungsanleitung

Cisco

Cisco ISA 3000 Bedienerhandbuch

Cisco

Cisco PIX 525 Bedienungsanleitung

Cisco

Cisco ISA 3000 Bedienungsanleitung

Cisco

Cisco PIX-515-RPS - PIX 515-R - Firewall Bedienungsanleitung

Cisco

Cisco 4116 - EtherFast Switch Leitfaden

Cisco

Cisco ISA550 Bedienungsanleitung

Cisco

Cisco Firepower 2100 Series Handbuch

Cisco

Cisco Small Business Pro SA 500 Series Bedienungsanleitung

Cisco

Cisco Firepower 1100 Series Bedienungsanleitung

Cisco

Cisco Telepresence MX200 Bedienungsanleitung

Cisco

Cisco Meraki MX67 Bedienungsanleitung

Cisco

Cisco Firepower 2100 Series Handbuch

Cisco

Cisco MS410-16 Bedienungsanleitung

Cisco

Cisco MARS Gebrauchsanweisung

Cisco

Cisco ASA 55 Series Kurzanleitung

Cisco

Cisco 500 Series Bedienungsanleitung

Cisco

Cisco WVC200 - Wireless-G PTZ Internet Camera Bedienungsanleitung

Cisco

Cisco ASA 5506W-X Handbuch

Cisco

Cisco 6400E Bedienungsanleitung

Cisco

Cisco MEDVIEW-C-30XS-A01 Bedienungsanleitung

Cisco

Cisco Codec C Series Bedienungsanleitung

Cisco

Cisco C395 Handbuch

Cisco

Cisco M5 Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung

DSC

DSC PC 4010 Betriebsanleitung

UniPOS

UniPOS 6202L Bedienungsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Rondish

Rondish Nexus Bedienungsanleitung