Cisco M5 Bedienungsanleitung
Maintenance and Upgrades
•Power Button Shut Down, on page 1
•Remove and Replace a Drive, on page 2
•Remove and Replace a Power Supply, on page 4
Power Button Shut Down
The Threat Grid M5 runs in two modes:
• Main power mode—Power is supplied to all Threat Grid M5 components and all operating systems can
run.
• Standby power mode—Power is supplied only to the service processor and certain components. You can
safely remove power cords from the Threat Grid M5 in this mode.
After you shut down the Threat Grid M5 to standby power, electric current is still present in the chassis. To
completely remove power as directed in some maintenance procedures, you must disconnect all power cords
from all power supplies on the Threat Grid M5.
Caution
You can shut down the Threat Grid M5 using the front panel Power button or use OpAdmin to initiate a reboot
or shutdown.
Step 1 Check the Power LED:
• Amber—The Threat Grid M5 is already in standby mode and you can safely remove power.
• Green—The Threat Grid M5 is in main power mode and you must shut it down before you can safely remove power.
Step 2 Perform a graceful shutdown or a hard shutdown:
To avoid data loss or damage to your operating system, perform a graceful shutdown of the operating system.
Caution
• Graceful shutdown—Press and release the Power button. The operating system performs a graceful shutdown and
the Threat Grid M5 goes into standby mode. The power LED is amber.
•Emergency shutdown—Press and hold the Power button for four seconds to force the main power off and immediately
enter standby mode.
Maintenance and Upgrades
1
Step 3 If a maintenance procedure instructs you to completely remove power from the Threat Grid M5, disconnect all power
cords from the power supplies.
Remove and Replace a Drive
The drives are hot-swappable. You do not have to shut down the Threat Grid M5 to remove or replace drives.
Note
You cannot add more drives to the chassis. You can only replace the drives in the slots that shipped with your
Threat Grid M5.
Note
Before you begin
Take note of the following warnings:
Statement 1018—Supply Circuit
To reduce risk of electric shock and fire, take care when connecting units to the supply circuit so that wiring
is not overloaded.
Warning
Statement 1019—Main Disconnecting Device
The plug-socket combination must be accessible at all times, because it serves as the main disconnecting
device.
Warning
Statement 1024—Ground Conductor
This equipment must be grounded. To reduce the risk of electric shock, never defeat the ground conductor or
operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical
inspection authority or an electrician if you are uncertain that suitable grounding is available.
Warning
Statement 1030—Equipment Installation
Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Warning
Maintenance and Upgrades
2
Maintenance and Upgrades
Remove and Replace a Drive
Statement 1073—No User-Serviceable Parts
There are no serviceable parts inside. To avoid risk of electric shock, do not open.
Warning
Statement 1074—Comply with Local and National Electrical Codes
To reduce risk of electric shock or fire, installation of the equipment must comply with local and national
electrical codes.
Warning
Step 1 Remove the drive that you are replacing:
a) Press the release button on the face of the drive tray.
b) Grasp and open the ejector lever and then pull the drive tray out of the slot.
Figure 1: Remove the Drive
Release button2Ejector handle1
Step 2 Remove the four drive-tray screws that secure the drive to the tray and then lift the drive out of the tray.
Maintenance and Upgrades
3
Maintenance and Upgrades
Remove and Replace a Drive
Figure 2: Remove the Drive Tray
Drive removed from drive tray2Drive tray screws (two on each side)1
Step 3 Install a new drive:
a) Place a new drive in the empty drive tray and install the four drive-tray screws.
b) With the ejector lever on the drive tray open, insert the drive tray into the empty drive bay.
c) Push the tray into the slot until it touches the backplane, and then close the ejector lever to lock the drive in place.
Remove and Replace a Power Supply
The Threat Grid M5 ships with two power supplies, which are redundant and hot-swappable. One is the active
power supply and the other is the standby power supply (1+1).
The Threat Grid M5 also supports cold redundancy. Depending on the power being drawn by the Threat Grid
M5, one power supply might actively provide all power to the system while the remaining power supply is
put into a standby state. For example, if the power consumption can be satisfied by power supply 1, then
power supply 2 is put into a standby state.
When you replace power supplies, do not mix power supply types in the Threat Grid M5. Both power supplies
must be the same wattage and Cisco PID.
Caution
Maintenance and Upgrades
4
Maintenance and Upgrades
Remove and Replace a Power Supply
Power supply health monitoring notifies you if the power supply loses power or malfunctions so that redundancy
is lost. Check the power supply cables to make sure they are functioning. If they are and errors are still
occurring, replace the power supply.
Trouble
Before you begin
Take note of the following warnings:
Statement 1018—Supply Circuit
To reduce risk of electric shock and fire, take care when connecting units to the supply circuit so that wiring
is not overloaded.
Warning
Statement 1019—Main Disconnecting Device
The plug-socket combination must be accessible at all times, because it serves as the main disconnecting
device.
Warning
Statement 1024—Ground Conductor
This equipment must be grounded. To reduce the risk of electric shock, never defeat the ground conductor or
operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical
inspection authority or an electrician if you are uncertain that suitable grounding is available.
Warning
Statement 1030—Equipment Installation
Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Warning
Statement 1073—No User-Serviceable Parts
There are no serviceable parts inside. To avoid risk of electric shock, do not open.
Warning
Statement 1074—Comply with Local and National Electrical Codes
To reduce risk of electric shock or fire, installation of the equipment must comply with local and national
electrical codes.
Warning
Step 1 Remove the power supply:
Maintenance and Upgrades
5
Maintenance and Upgrades
Remove and Replace a Power Supply
a) Grasp the power supply handle while pinching the release lever toward the handle.
b) Pull the power supply out of the bay.
Figure 3: Remove and Replace the AC Power Supply
Handle2Release lever1
Step 2 Install a new power supply:
a) Grasp the power supply handle and insert the new power supply into the empty bay.
b) Push the power supply into the bay until the release lever locks.
c) Connect the power cord to the new power supply.
d) If you shut down the Threat Grid M5, press the Power button to return it to main power mode.
Maintenance and Upgrades
6
Maintenance and Upgrades
Remove and Replace a Power Supply
Andere Handbücher für M5
2
Inhaltsverzeichnis
Andere Cisco Sicherheitssystem Handbücher
Cisco
Cisco Firepower 1100 Series Bedienungsanleitung
Cisco
Cisco IronPort S670 Bedienungsanleitung
Cisco
Cisco 4116 - EtherFast Switch Leitfaden
Cisco
Cisco Firepower 2100 Series Handbuch
Cisco
Cisco MEDVIEW-C-30XS-A01 Bedienungsanleitung
Cisco
Cisco ISA550 Bedienungsanleitung
Cisco
Cisco ISA 3000 Bedienerhandbuch
Cisco
Cisco Codec C Series Bedienungsanleitung
Cisco
Cisco ASA 5506W-X Handbuch
Cisco
Cisco NCS 4000 Series Bedienungsanleitung
Cisco
Cisco PIX 501 - Security Appliance Bedienungsanleitung
Cisco
Cisco PIX 525 Bedienungsanleitung
Cisco
Cisco MS410-16 Bedienungsanleitung
Cisco
Cisco ISA 3000 Bedienungsanleitung
Cisco
Cisco 6400E Bedienungsanleitung
Cisco
Cisco Meraki MX67 Bedienungsanleitung
Cisco
Cisco C195 Kurzanleitung
Cisco
Cisco WVC200 - Wireless-G PTZ Internet Camera Bedienungsanleitung
Cisco
Cisco Small Business Pro SA 500 Series Bedienungsanleitung
Cisco
Cisco Firepower 2100 Series Handbuch
Beliebte Sicherheitssystem Handbücher anderer Marken
EDM
EDM Solution 6+6 Wireless-AE Bedienungsanleitung
Highway Safety Group
Highway Safety Group EA401 Bedienungsanleitung
Siren
Siren LED GSM Bedienungsanleitung
Detection Systems
Detection Systems 7090i Montageanleitung
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung
Siemens
Siemens FDM273 Bedienungsanleitung