Cisco 5509 - Catalyst Chassis Switch Bedienungsanleitung

Quick Installation Guide

CATALYST 5509

Prepare for Installation

Rack-Mount the Switch

Connect the Switch to the Network

Connect the Power

Start the System

INSTRUCTIONS FOR INSERTING AND REMOVING MODULES AND POWER SUPPLIES BEGIN ON PAGE 13.

OK FAN

OK OUTPUT

FAIL

OK FAN

OK OUTPUT

FAIL

PORT 2

Switch Load PCMCIA EJECT

100%

10/100Mbps

LINK

CONSOLE AUX

PORT 1

RESET

FAN

SLOT1

SLOT0

ACTIVE

PS1

PS2

SUPERVISORENGINE II I

10/100 FAST ETHERCHANNEL

MDIX MDIX

WS-U5531-FETX

WS-x5530

10/100Mbps

LINK

SYSTEM

STATUS

PORT 2

Switch Load PCMCIA EJECT

100%

10/100Mbps

LINK

CONSOLE AUX

PORT 1

RESET

FAN

SLOT1

SLOT0

ACTIVE

PS1

PS2

SUPERVISORENGINE II I

10/100 FAST ETHERCHANNEL

MDIX MDIX

WS-U5531-FETX

WS-x5530

10/100Mbps

LINK

SYSTEM

STATUS

FASTETHERNET SWITCHING MODULE

STATUS

FASTETHERNET SWITCHING MODULE

STATUS

FASTETHERNET SWITCHING MODULE

OK FAN

OK OUTPUT

FAIL

OK FAN

OK OUTPUT

FAIL

EJECT AUX

CONSOLE

UTP3

Prepare for Installation

Note: This Quick Installation Guide is intended for experienced installers. For detailed

hardware installation instructions, refer to the Catalyst 5000 Series Installation Guide and the

Catalyst 5000 Series Module Installation Guide.

1Check the packing slip to ensure that all the proper components are present.

2Ensure the site is set up properly:

• Prepare equipment racks

• Ensure the environment is within specification

• Prepare network connections

3Obtain the following equipment:

• ESD grounding strap and antistatic mat

• Numbers 1 and 2 Phillips screwdrivers and 3/16-inch flat blade screwdriver

• Tape measure and level

4Ensure your safety when installing the Catalyst 5509 switch:

• Lift the chassis safely

• Cooperate with the natural laws of electricity

• Ensure that the power service at your site is suitable for the chassis you are

connecting

5Take steps to prevent ESD damage to electronic

components:

• Use an ESD wrist strap when handling

modules or coming into contact with

internal components (see figure)

• Handle modules by the edges only

• Place modules in a static shielding bag

when not installed

Rack-Mount the Switch

Install the shelf brackets and crossbar bracket

1Secure each shelf bracket to the rack using six (three

per side) 12-24 or 10-32 screws.

2Attach the crossbar bracket to the back of the shelf

brackets using two (one per side) M3 screws.

Note: The shelf brackets and crossbar support the

chassis in the rack, so no shelf is required.

Attach the L brackets and cable guide to the chassis

1Attach the L brackets to the chassis using the eight M4 Phillips countersunk-head screws

provided in the rack-mount kit.

2(Optional) Attach the cable guide using the screws provided in the cable management kit.

Cable

guide

OK FAN

OK OUTPUT

FAIL

OK FAN

OK OUTPUT

FAIL

PORT 2

Switch Load PCMCIA EJECT

100%

10/100Mbps

LINK

CONSOLE AUX

PORT 1

RESET

FAN

SLOT1

SLOT0

ACTIVE

PS1

PS2

SUPERVISORENGINE II I

10/100 FAST ETHERCHANNEL

MDIX MDIX

WS-U5531-FETX

WS-x5530

10/100Mbps

LINK

SYSTEM

STATUS

PORT 2

Switch Load PCMCIA EJECT

100%

10/100Mbps

LINK

CONSOLE AUX

PORT 1

RESET

FAN

SLOT1

SLOT0

ACTIVE

PS1

PS2

SUPERVISORENGINE II I

10/100 FAST ETHERCHANNEL

MDIX MDIX

WS-U5531-FETX

WS-x5530

10/100Mbps

LINK

SYSTEM

STATUS

FASTETHERNET SWITCHING MODULE

STATUS

FASTETHERNET SWITCHING MODULE

STATUS

FASTETHERNET SWITCHING MODULE

L bracket

Shelf bracket

Crossbar bracket

Rack-Mount the Switch (continued)

Install the switch in the rack

Note: Three people are required to install the switch in an open rack. To make the switch

easier to lift, remove the power supplies and modules before installing the switch in the rack.

1Position one person on each side of the chassis. Lift the switch and position it on the shelf

brackets and crossbar.

2Align the mounting holes in the L brackets with the mounting holes in the rack.

3Have the third person secure the chassis by inserting the mounting screws through the holes

in the L brackets and into the threaded holes in the mounting posts.

4Use a tape measure and level to ensure the chassis is installed straight and level.

OK FAN

OK OUTPUT

FAIL

OK FAN

OK OUTPUT

FAIL

STATUS

FASTETHERNET SWITCHING MODULE

STATUS

FASTETHERNET SWITCHING MODULE

STATUS

FASTETHERNET SWITCHING MODULE

L bracket

OK FAN

OK OUTPUT

FAIL

OK FAN

OK OUTPUT

FAIL

PORT2

Switch Load PCMCIA EJECT

100%

10/100Mbps

LINK

CONSOLE AUX

PORT1

RESET

FAN

SLOT1

SLOT0

ACTIVE

PS1

PS2

SUPERVISORENGINE III

10/100 FAST ETHERCHANNEL

MDIX MDIX

WS-U5531-FETX

WS-x5530

10/100Mbps

LINK

SYSTEM

STATUS

PORT2

Switch Load PCMCIA EJECT

100%

10/100Mbps

LINK

CONSOLE AUX

PORT1

RESET

FAN

SLOT1

SLOT0

ACTIVE

PS1

PS2

SUPERVISORENGINE III

10/100 FAST ETHERCHANNEL

MDIX MDIX

WS-U5531-FETX

WS-x5530

10/100Mbps

LINK

SYSTEM

STATUS

FASTETHERNET SWITCHING MODULE

STATUS

STATUS 1

STATUS

FASTETHERNET SWITCHING MODULE

FASTETHERNETSWITCHINGMODULE

FASTETHERNET SWITCHING MODULE

STATUS

FASTETHERNET SWITCHING MODULE

CONSOLE AUX

RESET

ACTIVE

CONSOLE

Connect the Switch to the Network

Connect a terminal to the console port

Supervisor Engines I and II

To connect a terminal to the Supervisor Engine I

orII console port, plug an EIA/TIA-232 (RS-232)

DCE DB-25-to-DTE DB-25 straight-through

cable into the console port.

Supervisor Engine III

To connect a terminal to the Supervisor

Engine III console port, plug an

RJ-45-to-RJ-45 straight-through cable into

the console port jack. Use an RJ-45-to-DB-25

or RJ-45-to-DB-9 adapter to connect to the

terminal.

Caution TopreventESDdamagetoelectroniccomponents,alwaysuseanESDwrist

strap when handling modules or coming into contact with internal components.

LINK

100 MBPS

A411

PORT 1

MDIX

1-8

9-16

Connect the Switch to the Network (continued)

Connect the switch ports to the network

Note: If you are not sure which cable and connector to use for a particular module, refer to

the Catalyst 5000 Series Module Installation Guide.

RJ-45

To connect to modules with RJ-45 interfaces, use

Category 5 UTP (100BaseTX, 10/100BaseTX, CDDI,

Token Ring, ATM), Category 3 UTP (10BaseT), or Type 1

STP (Token Ring) cables with male RJ-45 interfaces.

Media-Independent Interface (MII)

Supervisor Engine I and II modules with 100BaseTX

uplinks have MII portsinaddition toRJ-45 ports.To

connect to the MII interfaces, use Category 5 UTP

cables with male MII connectors.

PORTS

1-12

10BaseT

Connect the Switch to the Network (continued)

RJ-21 Telco

Toconnecttomoduleswith RJ-21Telcointerfaces,use

Category 3 UTP cable with male RJ-21 Telco

connectors.

SC-Type Fiber Optic

To connect to modules with SC-type fiber-optic interfaces,

use single-mode or multimode fiber-optic cable with male

SC-type connectors.

ST-Type Fiber Optic

To connect to modules with ST-type fiber-optic

interfaces, use single-mode (FDDI) or multimode

(10BaseFL) fiber-optic cable with male ST-type

connectors.

ACTIVE

LINK

PORT A

UNI-155SM

LINK

DS3 (45 Mbps)

BNC

ACTIVE

LINK

PORT

Connect the Switch to the Network (continued)

MIC-Type Fiber Optic

To connect to the FDDI module MMF

(WS-X5101), use multimode fiber-optic cable

with a male MIC-type connector.

BNC

To connect to the ATM dual PHY DS3 module

(WS-X5166), use 75-ohm RG-59 coaxial cable with

male BNC connectors.

Connect the Power

AC power supplies

1Verify that each power supply is properly installed in its bay. Make sure the power supplies

are OFF (0).

2Connect an AC power cable to each power supply. Use the retaining clip to secure the cord

to each power supply connection.

3Attach each power cable to a grounded outlet. If possible, connect each cable to an outlet

on a separate circuit. Make sure that the source power is within range.

Warning Before you work on anyequipment, be awareof the hazards involved with

electrical circuitry and be familiar with standard practices for preventing accidents.

Caution TopreventESDdamagetoelectroniccomponents,alwaysuseanESDwrist

strap when handling modules or coming into contact with internal components.

OK FAN

OK OUTPUT

FAIL

4Connect the Power (continued)

DC power supplies

1Verify that each power supply is correctly installed in its bay and that the power switches

are OFF (0).

2On each power supply, remove the screws securing the terminal block cover and slide the

cover straight off the terminal block.

3Attach the appropriate lugs to the DC-input wires. (Suggested lugs are AMP 322985 or

52941; suggested DC-input wires are 10-AWG copper conductors.)

4Wire the DC-input power supply to the terminal block (see figure), ensuring that all wire

connections are secure:

a) Connect the ground wire to the ground terminal (you should always connect the

ground wire first and disconnect it last)

b) Connect the –48V wire to the “−” terminal

c) Connect the –48V return to the “+” terminal

Warning Before performing the following procedure, remove power to the

DC-input circuit by turning the circuit breaker OFF.

OK OK

FAN OUTPUT

FAIL

Positive (+)

Negative (-)

Ground

Inhaltsverzeichnis

Andere Cisco Schalten Handbücher

Cisco

Cisco Nexus 5596UP Handbuch

Cisco

Cisco Nexus 7000 Series Installations- und Betriebsanleitung

Cisco

Cisco SFS 7008 Montageanleitung

Cisco

Cisco Nexus 1000V Bedienungsanleitung

Cisco

Cisco Catalyst 9500 Series Handbuch

Cisco

Cisco 4900M - Catalyst Switch Bedienungsanleitung

Cisco

Cisco Linksys SGE2000P Bedienungsanleitung

Cisco

Cisco Catalyst Express 500 Bedienungsanleitung

Cisco

Cisco Nexus 9516 Handbuch

Cisco

Cisco Catalyst 6807-XL Betriebsanleitung

Cisco

Cisco N5K-M1600 - Expansion Module - 6 Ports Bedienungsanleitung

Cisco

Cisco Nexus 9516 Handbuch

Cisco

Cisco LightStream 100 Bedienungsanleitung

Cisco

Cisco 2950 - Catalyst Switch Bedienungsanleitung

Cisco

Cisco Nexus 9336PQ Handbuch

Cisco

Cisco SG200 Series Bedienungsanleitung

Cisco

Cisco RSP8 Bedienerhandbuch

Cisco

Cisco Nexus 3000 series Handbuch

Cisco

Cisco Catalyst X6816 Handbuch

Cisco

Cisco Catalyst 2924M XL Bedienungsanleitung

Cisco

Cisco 3750G-12S - Catalyst Switch - Stackable Handbuch

Cisco

Cisco Meraki MX64 Bedienungsanleitung

Cisco

Cisco SCE8000 GBE Bedienerhandbuch

Cisco

Cisco 300 Series Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung