Cisco Catalyst 3030 Bedienungsanleitung

1-1

Cisco Catalyst Blade Switch 3030 Getting Started Guide

78-17052-01

Cisco Catalyst Blade Switch 3030

Getting Started Guide

This guide provides instructions on how to install your Cisco Catalyst Blade

Switch 3030—hereafter referred to as the switch module—in the Dell Modular

Server Chassis and to set up and configure your switch module. The Dell Modular

Server Chassis—hereafter referred to as the server chassis—is a system that

supports up to ten server modules and up to four Ethernet switch modules. The

switch module is installed in one of the chassis I/O module bays on the rear panel

of the server chassis.

Also covered in this guide are switch management options and troubleshooting

help for the switch module.

For details on the number, types, and the location of the module bays and for

additional information on the entire modular server system, see the Dell

PowerEdge 1855 Systems User's Guide and the Dell PowerEdge 1855 Systems

Installation and Troubleshooting Guide at www.support.dell.com.

For additional installation and configuration information about the switch

module, see the Cisco Catalyst Blade Switch 3030 documentation on Cisco.com.

For system requirements, important notes, limitations, open and resolved caveats,

and last-minute documentation updates about the switch module, see the release

notes, also on Cisco.com.

When using the online publications, refer to the documents that match the Cisco

IOS software version that is running on the switch. You can order printed copies

of the manuals from the Cisco.com sites and from the telephone numbers listed in

the “Obtaining Documentation” section on page 1-24.

Cisco Catalyst Blade Switch 3030 Getting Started Guide

Contents

1-2

Cisco Catalyst Blade Switch 3030 Getting Started Guide

78-17052-01

For translations of the warnings that appear in this publication, see the Regulatory

Compliance and Safety Information for the Cisco Catalyst Blade Switch 3030

Getting Started Guide that accompanies this guide.

Note Before proceeding, read the release notes for the server chassis. The release notes

are available on the Dell support website at www.support.dell.com.

Contents

•Taking Out What You Need, page 1-2

•Dell Modular Server Chassis Architecture, page 1-5

•Installing the Switch Module in the Server Chassis, page 1-6

•Configuring the Switch Module, page 1-9

•Managing the Switch, page 1-16

•Installation Warning Statements, page 1-18

•In Case of Difficulty, page 1-22

•Obtaining Documentation, page 1-24

•Documentation Feedback, page 1-26

•Cisco Product Security Overview, page 1-26

•Obtaining Technical Assistance, page 1-28

•Obtaining Additional Publications and Information, page 1-30

•Hardware Warranty Terms, page 1-32

Taking Out What You Need

These items ship with your switch module:

•Console cable

•Cisco Catalyst Blade Switch 3030 Getting Started Guide (this book)

1-3

Cisco Catalyst Blade Switch 3030 Getting Started Guide

78-17052-01

Cisco Catalyst Blade Switch 3030 Getting Started Guide

Taking Out What You Need

•Regulatory Compliance and Safety Information for the Cisco Catalyst Blade

Switch 3030

•Registration card

Follow these steps:

1. Unpack and remove the switch module and the accessory kit from the

shipping box.

2. Return the packing material to the shipping container, and save it for

future use.

Note If the switch modules are ordered with the server chassis, the switch modules are

already installed, and no unpacking is required. The unpacking procedure applies

only if a switch module is ordered separately.

Cisco Gigabit Ethernet Switch Module Description

Figure 1 shows the switch module, which has these features:

•10 internal Gigabit Ethernet 1000BASE-X ports

•1 console port

•2 external 10/100/1000BASE-T copper Gigabit Ethernet ports

•4 external small form-factor pluggable (SFP) module uplink ports that

support 1000BASE-SX fiber and 10/100/1000BASE-T copper (only Cisco

SFP modules are supported)

Each port has an LED associated with it. Additionally, there is a System

Status/ID LED that is controlled by the Dell Remote Access Controller/Modular

Chassis (DRAC/MC) management board.

Cisco Catalyst Blade Switch 3030 Getting Started Guide

Taking Out What You Need

1-4

Cisco Catalyst Blade Switch 3030 Getting Started Guide

78-17052-01

Figure 1 The Cisco Gigabit Ethernet Switch Module

You need to supply this equipment to set up your switch module:

•PC

•Ethernet (Category 5) straight-through cable (as shown) or console cable

1Switch module 6Gigabit Ethernet port LEDs

2Console port 7SFP module ports

3Console port LED 8SFP module port LEDs

4System Status/ID LED 9Release latch

5Gigabit Ethernet ports

143470

11x 12x 13x 14x 15x 16x

Console

11x 12x

13x 14x 15x 16x

CON

1-5

Cisco Catalyst Blade Switch 3030 Getting Started Guide

78-17052-01

Cisco Catalyst Blade Switch 3030 Getting Started Guide

Dell Modular Server Chassis Architecture

The four chassis I/O module bays are on the rear panel (see Figure 2). You can

insert switch modules into the chassis I/O module bays 1 and 2. Use bays 3 and 4

for switch modules only if a Gigabit Ethernet daughter card is installed on the

server modules.

Figure 2 Dell Modular Server Chassis

1Bay 1 (populated with switch

module)

5Rear panel of server chassis

2Bay 2 6DRAC/MC management board

3Bay 3 7Ethernet port

4Bay 4 8RS-232 port

143471

11x 12x 13x 14x 15x 16x

Console

11x 12x

13x 14x 15x 16x

Cisco Catalyst Blade Switch 3030 Getting Started Guide

Installing the Switch Module in the Server Chassis

1-6

Cisco Catalyst Blade Switch 3030 Getting Started Guide

78-17052-01

Consider these prerequisites before installing your switch module:

•Bay 1 and bay 2 are a pair. Bay 1 must be populated before bay 2. If bay 2 is

used, the I/O module in bay 2 must be the same type as the one in bay 1.

•Bay 3 and bay 4 are a pair. Bay 3 must be populated before bay 4. If bay 4 is

used, the I/O module in bay 4 must be the same type as the one in bay 3.

For more information about the components of the information panel, see the Dell

PowerEdge 1855 Systems User's Guide and the Dell PowerEdge 1855 Systems

Installation and Troubleshooting Guide.

Installing the Switch Module in the Server Chassis

Before you install the switch module in the server chassis, consider these points:

•Review and become familiar with the safety and handling guidelines

specified in the Product Information Guide.

•Review the and the Regulatory Compliance and Safety Information for the

Cisco Catalyst Blade Switch 3030 that accompanies this guide.

•To help ensure proper cooling and system reliability, keep these points in

mind:

–

Each chassis I/O module bay must contain either a module or an end-cap

(blank plug).

–

When you remove a hot-swap module, you must replace it with an

identical module or an end-cap (blank plug) within 1 minute of removal.

Caution To prevent electrostatic-discharge (ESD) damage when installing switch modules,

follow your normal board and component handling procedures.

Note When you install a switch module, you do not need to power down the server

modules or the switch.

1-7

Cisco Catalyst Blade Switch 3030 Getting Started Guide

78-17052-01

Cisco Catalyst Blade Switch 3030 Getting Started Guide

Installing the Switch Module in the Server Chassis

Note The initial configuration assumes that the switch module was never configured,

that it is in the same state as when it was received, and that it is not configured

with a default username and password.

Follow these steps to install the switch module into the server chassis:

Step 1 Obtain and make note of this information from your network administrator before

you begin the switch module installation:

•Switch IP address

•Subnet mask (IP netmask)

•Default gateway (router)

•Enable secret password (encrypted)

•Enable password (not encrypted)

•Telnet password

•SNMP community strings (optional)

Step 2 Select a chassis I/O module bay in which to install the switch module. Follow the

prerequisites listed in the “Dell Modular Server Chassis Architecture” section on

page 1-5.

Step 3 Remove the end-cap (blank plug) from the selected bay. Store the end-cap (blank

plug) for future use.

Step 4 If you have not already done so, touch the static-protective package that contains

the switch module to an unpainted metal part of the server chassis for at least 2

seconds.

Step 5 Remove the switch module from its static-protective package.

Step 6 Ensure that the release latch on the switch module is in the open position

(perpendicular to the module):

143473

11x 12x 13x 14x 15x 16x

Console

11x 12x

13x 14x 15x 16x

CON

Cisco Catalyst Blade Switch 3030 Getting Started Guide

Installing the Switch Module in the Server Chassis

1-8

Cisco Catalyst Blade Switch 3030 Getting Started Guide

78-17052-01

Step 7 Slide the switch module into the appropriate bay until it stops.

Step 8 Push the release latch on the front of the switch module to the closed position.

Figure 3 shows the switch module being inserted into the server chassis.

Figure 3 Inserting the Switch Module into the Server Chassis

1Switch module 3Release latch

2Server chassis

143472

11x12x13x14x15x16x

Console

11x12x

13x 14x 15x 16x

1-9

Cisco Catalyst Blade Switch 3030 Getting Started Guide

78-17052-01

Cisco Catalyst Blade Switch 3030 Getting Started Guide

Installing the Switch Module in the Server Chassis

Configuring the Switch Module

Note To run the system configuration dialog, you must first connect the switch to a PC

to run a terminal emulation program. There are two ways you can connect the PC

to the switch: either through the switch console port or through the DRAC/MC

console port. Instructions for these two procedures are included in this section.

If you connect to the switch through the DRAC/MC, the switch console port is

disabled. After you have completed the configuration procedure, you must use the

disconnect command to close the active console port and re-enable the switch

console port. Type logout to log out of the switch, then type ~. to disconnect the

DRAC/MC from the switch.

Follow one of these procedures:

•To run the terminal emulation program through the switch module console

port, go to “Connecting through the Switch Module Console Port” section on

page 1-9.

•To run the terminal emulation program through the DRAC/MC port, go to

“Connecting through the DRAC/MC” section on page 1-11.

Connecting through the Switch Module Console Port

Follow these steps when connecting through the switch module console port:

Step 1 Connect one end of the console cable to the switch module console port. Connect

the other end of the cable to the serial port of the computer that is running the

terminal emulation application. (See Figure 4.)

Cisco Catalyst Blade Switch 3030 Getting Started Guide

Installing the Switch Module in the Server Chassis

1-10

Cisco Catalyst Blade Switch 3030 Getting Started Guide

78-17052-01

Figure 4 Connecting through the Switch Module Console Port

Step 2 Start the terminal emulation session so you will be able to see the output display

from the power-on self-test (POST). The terminal-emulation software—a PC

application such as Hyperterminal or ProcommPlus—makes communication

between the switch and your PC or terminal possible.

Configure the baud rate and character format of the PC or terminal to match these

console port default characteristics:

•9600 baud

•8 data bits

•1 stop bit

•No parity

•None (flow control)

Step 3 Go to “Waiting for POST to Complete” section on page 1-13 to finish configuring

the switch module.

11x 12x 13x 14x 15x 16x

Console

11x 12x

13x 14x 15x 16x

CON

Andere Handbücher für Catalyst 3030

Inhaltsverzeichnis

Andere Cisco Schalten Handbücher

Cisco

Cisco Ethernet Connectors Jackscrew Bedienungsanleitung

Cisco

Cisco ME 3400 Series Betriebsanleitung

Cisco

Cisco Catalyst 4900 Series Bedienungsanleitung

Cisco

Cisco Catalyst 2960 Series Betriebsanleitung

Cisco

Cisco IE 4010 Handbuch

Cisco

Cisco Catalyst 3850 Handbuch

Cisco

Cisco VCO/4K Bedienungsanleitung

Cisco

Cisco 8800 Series Bedienungsanleitung

Cisco

Cisco Nexus 93180YC-FX Handbuch

Cisco

Cisco SLM224G4PS Bedienungsanleitung

Cisco

Cisco AJ732A - MDS 9134 Fabric Switch Bedienungsanleitung

Cisco

Cisco Nexus 93120TX Handbuch

Cisco

Cisco MDS 9000 Series Bedienungsanleitung

Cisco

Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module... Bedienungsanleitung

Cisco

Cisco Nexus 93360YC-FX2 Handbuch

Cisco

Cisco 9124 - mds multilayer fabric switch Bedienungsanleitung

Cisco

Cisco Catalyst X6324 Bedienungsanleitung

Cisco

Cisco Catalyst 6500-E Series Bedienungsanleitung

Cisco

Cisco Catalyst Intelligent Switching Bedienungsanleitung

Cisco

Cisco MDS 9396S Bedienungsanleitung

Cisco

Cisco Catalyst 3750-X Series Installationshandbuch

Cisco

Cisco Nexus 7000 Series Bedienungsanleitung

Cisco

Cisco Nexus 5500 Series Bedienungsanleitung

Cisco

Cisco 100 Series Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung