Cisco Nexus 93108TC-FX3P Handbuch
Cisco Nexus 93108TC-FX3P ACI-Mode Switch Hardware Installation
Guide
First Published: 2021-02-01
Last Modified: 2023-03-01
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 527-0883
©2021 Cisco Systems, Inc. All rights reserved.
CONTENTS
Overview 1
CHAPTER 1
Overview 1
Preparing the Site 5
CHAPTER 2
Temperature Requirements 5
Humidity Requirements 5
Altitude Requirements 5
Dust and Particulate Requirements 6
Minimizing Electromagnetic and Radio Frequency Interference 6
Shock and Vibration Requirements 7
Grounding Requirements 7
Planning for Power Requirements 7
Airflow Requirements 8
Rack and Cabinet Requirements 9
Clearance Requirements 9
Installing the Switch Chassis 11
CHAPTER 3
Safety 11
Installation Options with Rack-Mount Kits 14
Airflow Considerations 15
Installation Guidelines 15
Unpacking and Inspecting the Switch 16
Installing the Switch Using the NXK-ACC-KIT-1RU Rack-Mount Kit 16
Installing the Switch into a Two-Post Rack Using the NXK-ACC-KIT-1RU Rack-Mount Kit 20
Installing the Airflow Sleeve (N9K-AIRFLOW-SLV) 23
Grounding the Chassis 24
Cisco Nexus 93108TC-FX3P ACI-Mode Switch Hardware Installation Guide
iii
Starting the Switch 25
Connecting the Switch to the ACI Fabric 29
CHAPTER 4
ACI Fabric Topology 29
Preparing to Connect to Other Devices 30
Connecting Leaf Switches to APICs 31
Connecting Leaf Switches to Spine Switches 33
FEX Conversion and Support 34
Leaf to FEX Conversion 34
FEX to Leaf Conversion 35
New FEX Setup 35
Change an Existing Leaf in the Topology to FEX 35
Change an Existing FEX in the Topology to Leaf 35
Installing a Gigabit Ethernet module (GEM) 36
Migration of Nodes From a First Generation Switch to a Second Generation Switch 36
Setting Up an Optional Console Interface 38
Setting Up an Optional Management Connection 39
Maintaining Transceivers and Optical Cables 39
Replacing Components 41
CHAPTER 5
Replacing a Fan Module 41
Removing a Fan Module 41
Installing a Fan Module 42
Replacing a Power Supply Module 42
Replacing an AC Power Supply 42
Replacing a DC Power Supply 43
Rack Specifications 45
APPENDIX A
Overview of Racks 45
General Requirements for Cabinets and Racks 45
Requirements Specific to Standard Open Racks 46
Requirements Specific to Perforated Cabinets 46
Cable Management Guidelines 46
Cisco Nexus 93108TC-FX3P ACI-Mode Switch Hardware Installation Guide
iv
Contents
System Specifications 47
APPENDIX B
Environmental Specifications 47
Switch Dimensions 47
Switch and Module Weights and Quantities 48
Transceiver and Cable Specifications 48
Switch Power Input Requirements 48
Power Specifications 49
715-W DC Power Supply Specifications 49
1100-W AC Power Supply Specifications 49
1900-W AC Power Supply Specifications 50
Power Cable Specifications 50
Power Cables for NXA-PAC-1100W Power Supplies 50
DC Power Cable Specifications 52
Regulatory Standards Compliance Specifications 52
LEDs 55
APPENDIX C
Switch Chassis LEDs 55
Fan Module LEDs 56
Power Supply LEDs 56
Additional Kits 59
APPENDIX D
Rack Mount Kit NXK-ACC-KIT-1RU 59
Airflow Sleeve 60
Cisco Nexus 93108TC-FX3P ACI-Mode Switch Hardware Installation Guide
v
Contents
Cisco Nexus 93108TC-FX3P ACI-Mode Switch Hardware Installation Guide
vi
Contents
CHAPTER 1
Overview
•Overview, on page 1
Overview
The Cisco Nexus 93108TC-FX3P switch (N9K-C93108TC-FX3P, N9K-C93108TC-FX3H) is a 1-rack unit
(RU), fixed-port switch designed for spine-leaf-APIC deployment in data centers. PoE is supported on ports
1-48. This switch supports the following ports:
• 48 100M/1/2.5/5/10GBASE-T ports (ports 1-48).
• 6 40/100-Gigabit ports QSFP28 (ports 49-54)
• Two management ports (one 10/100/1000BASE-T port and one SFP port)
• One console port (RS-232)
• 1 USB port
This switch includes the following user-replaceable components:
• Fan modules (four) with the following airflow choices:
• Port-side exhaust fan module with blue coloring (NXA-FAN-35CFM-PE)
• Port-side intake fan module with burgundy coloring (NXA-FAN-35CFM-PI)
Table 1: Fan Speeds for This Switch
Port-Side Exhaust
Fan Speed %
Port-Side Intake
Fan Speed %
70%50%Typical/Minimum
100%100%Maximum
Note
Cisco Nexus 93108TC-FX3P ACI-Mode Switch Hardware Installation Guide
1
Each fan module has two rotors. The switch can function normally if one rotor
inside the any one fan module fails. In case of more than one rotor failure, the
switch will issue a warning and power down in 2 minute.
Note
This switch runs with +1 redundancy mode, so that if one fan fails, the switch
can sustain operation. But if a 2nd fan fails, this switch is not designed to sustain
operation. Hence before waiting for major threshold temperature to be hit, the
switch will power down due to Powered-down due to fan policy trigger.
Note
• Power supply modules (two—One for operations and one for redundancy [1+1]) with the following
choices:
• 715-W port-side intake DC power supply with blue coloring (NXA-PDC-715W-PI)
• 1100-W port-side exhaust AC power supply with blue coloring (NXA-PAC-1100W-PE)
• 1100-W port-side intake AC power supply with burgundy coloring (NXA-PAC-1100W-PI)
• 1900-W port-side intake AC power supply with burgundy coloring (NXA-PAC-1900W-PI)
The NXA-PDC-715W-PI power supply is only supported from Release 6.0.4 and
later.
Additional limitations when using the NXA-PDC-715W-PI power supply include
the following:
• SNMP query is not supported
• Power statistics and power redundancy policy are not supported
•show environment power command is not supported
• APIC display is not supported
• Syslog and faults are not supported and can be ignored
Note
All fan modules and power supplies must use the same airflow direction.
Note
The details of the 1900-W power supply (NXA-PAC-1900W-PI) will not display
in the CLI show commands, until a working power source is connected to the
power supply.
Note
Cisco Nexus 93108TC-FX3P ACI-Mode Switch Hardware Installation Guide
2
Overview
Overview
This switch may present access issues if installed between switches with greater
chassis depth. Please consider this before installation.
Note
The following figure shows the switch features on the port side of the chassis.
6 40/100-Gigabit QSFP28 ports3BCN, STS, ENV, and P LEDs1
48 100M/1/2.5/5/10GT ports2
To determine which transceivers, adapters, and cables are support this switch, see the Cisco Transceiver
Modules Compatibility Information document.
The following figure shows the switch features on the power supply side of the chassis.
Management port (1—SFP optical port)4Fan modules (4) with slots
numbered from 1 (left) to 4 (right)
1
USB port (1)5Console port (1)2
Power supply modules (1 or 2) (AC power supplies shown)
with slots numbered 1 (left) and 2 (right)
6Management port (1—RJ-45
copper port)
3
The following figure shows the side of the chassis.
Cisco Nexus 93108TC-FX3P ACI-Mode Switch Hardware Installation Guide
3
Overview
Overview
Grounding pad3Screw holes for mounting brackets1
Depending on whether you plan to position the ports in a hot or cold aisle, you can order the fan and power
supply modules with port-side intake or port-side exhaust airflow. For port-side intake airflow, the fan and
power supplies have burgundy coloring. For port-side exhaust airflow, the fan and power supplies have blue
coloring.
The fan and power supply modules are field replaceable. You can replace one fan module or one power supply
module during operations so long as the other modules are installed and operating. If you have only one power
supply installed, you can install the replacement power supply in the open slot before removing the original
power supply.
All fan and power supply modules must have the same direction of airflow. Otherwise, the switch can overheat
and shut down.
Note
If the switch has port-side intake airflow (burgundy coloring for fan modules), you must locate the ports in
the cold aisle. If the switch has port-side exhaust airflow (blue coloring for fan modules), you must locate the
ports in the hot aisle. If you locate the air intake in a hot aisle, the switch can overheat and shut down.
Caution
Cisco Nexus 93108TC-FX3P ACI-Mode Switch Hardware Installation Guide
4
Overview
Overview
Andere Handbücher für Nexus 93108TC-FX3P
2
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Cisco Schalten Handbücher
Cisco
Cisco Cisco mds 9216 - fabric switch Handbuch
Cisco
Cisco Catalyst 2960 Series Bedienungsanleitung
Cisco
Cisco SG300-52P-K9-NA Bedienungsanleitung
Cisco
Cisco AJ732A - MDS 9134 Fabric Switch Bedienungsanleitung
Cisco
Cisco CBS Series Technisches Datenblatt
Cisco
Cisco ESW-520-24 Bedienungsanleitung
Cisco
Cisco Meraki MS250 Series Bedienungsanleitung
Cisco
Cisco Catalyst 3750-X Series Bedienungsanleitung
Cisco
Cisco Nexus 5596UP Handbuch
Cisco
Cisco SLM2005 - Small Business Smart Switch Bedienungsanleitung
Cisco
Cisco SRW2024P - Small Business Managed Switch Bedienungsanleitung
Cisco
Cisco Catalyst WS-X6704-10GE Bedienungsanleitung
Cisco
Cisco Catalyst 3550 Installationshandbuch
Cisco
Cisco SFS 3012R Handbuch
Cisco
Cisco BTS 10200 Softswitch Bedienungsanleitung
Cisco
Cisco Catalyst 3550 Bedienungsanleitung
Cisco
Cisco Catalyst 4948E Bedienungsanleitung
Cisco
Cisco Catalyst 3560 Bedienungsanleitung
Cisco
Cisco Nexus 3000 series Handbuch
Cisco
Cisco Nexus 1000V Bedienungsanleitung
