Cisco SG300 series Bedienungsanleitung
Cisco SG300 Setup Guide
When used with ELAN Video Over IP products
Cisco SG300 SETUP GUIDE
02
www.elanhomesystems.com
Contents
Introduction 03
Cisco Feature Requirements 03
Connecting To The Web GUI Interface 04
Activating Layer 3 Mode 05
Jumbo Frames 06
IGMP Snooping 07-09
Turning On/O POE 10
Apply And Save Settings 11
Changing Your Computer IP Address 12-14
Cisco SG300 SETUP GUIDE
03
contact [email protected]
The ELAN Video Over IP solution requires a layer 3 Managed switch in order for
HDMI distribution to be achieved reliably and with no loss in performance.
The following guide is a step-by-step instruction on how to connect and congure
your Cisco SG300 Layer 3 Managed network switch.
Introduction
The following features need to be enabled on the Cisco network switch:-
1. Layer 3 mode
2. Jumbo Frame
3. IGMP Snooping/Video Over IP
4. POE (if utilised)
Feature explanation:
• Video Over IP (one-to-many or many-to-many distribution) is group communication where information is addressed to a
group of network devices simultaneously (ELAN Video Over IP products).
• Jumbo frames are Ethernet frames with more than 1500 bytes of payload. Conventionally, jumbo frames can carry up
to 9000 bytes of payload and must be activated in order to send large packets of data for HDMI distribution.
• IGMP management & snooping is the process of listening to Internet Group Management Protocol (IGMP) network trac.
The feature allows a network switch to listen in on the IGMP conversation between hosts, routers & receivers (Video
Over IP Transmitter, network switch and Video Over IP Receiver). By listening to this ow of trac the switch maintains
a map of which links need which IP Video Over IP streams. (which ELAN Video Over IP products are active and where
the signal is being distributed to).
Cisco feature requirements
Cisco SG300 SETUP GUIDE
04
www.elanhomesystems.com
Connecting to the switch Web GUI Interface
V2 Panel Description
To login into the Cisco network switch the factory default details are:
IP Address: 192.168.1.254
User: cisco
Password: cisco
In order to connect to the network switch your computer will need to be physically connected to the Cisco switch using a Ethernet
network cable.The computer must also be in the same IP range as the Cisco switch default IP address. If you are unsure how to update your
computer IP range follow the‘Changing your computer IP address’instructions at the rear of this guide.
1) Open your internet browser (Google Chrome, Mozilla, Internet Explorer etc)
2) Type the network switch default IP address into the web browser bar
3) Enter the default user name and password
Note: If the switch is not using the factory default settings you will need to know these login details or have to factory reset the unit.
For details how to factory reset the network switch please refer to the networks switch user manual.
Cisco SG300 SETUP GUIDE
05
contact [email protected]
The rst setting you MUST update is to turn the network switch to Layer 3 mode. This must be completed before all other setting
changes are made as this will default the factory settings when Layer 3 is activated.
Under ‘Administration’menu
Select ‘System settings’
Tick‘L3’(Layer 3) checkbox adjacent to System mode
Activating Layer 3 mode
Click‘Apply’to update the setting. A warning message will appear to make sure that you mean to factory reset the switch. Click
‘OK’to proceed.
Please note: The switch will reboot which will take 3-4 minutes. After this is complete you will have to re-enter new password
details
Cisco SG300 SETUP GUIDE
06
www.elanhomesystems.com
To enable Jumbo Frame,
Under ‘Port Management’menu
Select ‘Port settings’
Tick‘ENABLED’checkbox adjacent to Jmubo Frames
tick‘Jumbo Frame’checkbox under Port Settings
Jumbo Frame
Click‘Apply’to update the setting
Cisco SG300 SETUP GUIDE
07
contact [email protected]
To enable IGMP snooping, there are several steps required to enable this feature:-
• Bridge Video Over IP Filter Status
• IGMP Snooping Status
• IGMP Querier Status
• MRouter Ports Auto Learn
• Immediate Leave
• IGMP Querier Election
The following pages explain how to update the above settings.
IGMP Snooping
Under‘Video Over IP’menu
Select ‘Properties’
Tick‘Enabled’checkbox adjacent to‘Bridge Video Over IP Filter Status’
IGMP Snooping - Bridge Video Over IP Filter Status
Conrm other settings match those as shown in the above image
Click‘APPLY’to update the setting
Cisco SG300 SETUP GUIDE
08
www.elanhomesystems.com
Under‘Video Over IP’menu
Select ‘IPv4 Video Over IP Conguration’
Select ‘IGMP Snooping’
Tick‘Enabled’checkbox adjacent to IGMP Snooping Status
Tick‘Enabled’checkbox adjacent to IGMP Query Status
IGMP Snooping - IGMP Snooping Status
Conrm other settings match those as shown in the above image
Click‘APPLY’to update the setting
Cisco SG300 SETUP GUIDE
09
contact [email protected]
Under‘Video Over IP’menu
Select ‘IPv4 Video Over IP Conguration’
Select ‘IGMP Snooping’
Select Line 1 in the IGMP Snooping table and click the ‘EDIT’button
IGMP Snooping - IGMP Query Status, Mrouter ports auto
learn, Immediate leave & IGMP querier election
Tick‘Enabled’checkbox adjacent to IGMP Snooping Status
Tick‘Enabled’checkbox adjacent to Mrouter ports auto learn
Tick‘Enabled’checkbox adjacent to immediate leave
Tick‘Enabled’checkbox adjacent to IGMP querier status
Tick‘Enabled’checkbox adjacent to IGMP querier election
Conrm other settings match those as shown in the above image
Click‘APPLY’to update the setting
the following pop-up window will appear
Cisco SG300 SETUP GUIDE
10
www.elanhomesystems.com
Not all Cisco SG300 switches support POE. Those network switches that do support POE come with this as factory default to
‘ON’. If you are unsure of the port setting please follow the below instructions.
Under‘Port management’ menu
Select ‘POE’
Select ‘settings’
The following table shows the settings for each RJ45 LAN port on the network switch. POE administrative Status should be set to
‘Enabled’meaning the POE feature is active. Default settings are for POE to be active (Enabled) so changes shoudl not be required.
If status is‘Disabled please follow below instructions.
Turning On/O POE
To update the port settings click‘EDIT’which will open the following window:
Tick‘Enabled’checkbox for each interface (switch LAN connection) you wish POE to be active.
Click‘APPLY’to update the setting
Andere Handbücher für SG300 series
1
Inhaltsverzeichnis
Andere Cisco Schalten Handbücher
Cisco
Cisco SRW224G4P - Small Business Managed Switch Kurzanleitung
Cisco
Cisco AJ732A - MDS 9134 Fabric Switch Bedienungsanleitung
Cisco
Cisco Catalyst 3120G Gebrauchsanweisung
Cisco
Cisco WS-C2955T-12 Kurzanleitung
Cisco
Cisco Catalyst 2960 Series Bedienungsanleitung
Cisco
Cisco Nexus 9808 NX-OS Handbuch
Cisco
Cisco Catalyst 3560 Handbuch
Cisco
Cisco CBS 350 Series Technisches Datenblatt
Cisco
Cisco C9200L-24T-4X-A Handbuch
Cisco
Cisco Nexus 9508 Handbuch
Cisco
Cisco ME 3400E Handbuch
Cisco
Cisco Cisco Line Card 4500 E-Series Bedienungsanleitung
Cisco
Cisco 3020 - Cisco Catalyst Blade Switch Bedienungsanleitung
Cisco
Cisco HyperSwitch A100 Bedienungsanleitung
Cisco
Cisco Nexus 9200 Series Bedienungsanleitung
Cisco
Cisco ME 6500 Bedienungsanleitung
Cisco
Cisco Nexus 3000 series Bedienungsanleitung
Cisco
Cisco WS-C2950-12 Handbuch
Cisco
Cisco 3750 - Catalyst EMI Switch Installationshandbuch
Cisco
Cisco Nexus 9348GC-FX3PH Handbuch
