Cisco Small Business SF200-24P Bedienungsanleitung

Quick Start Guide

Cisco Small Business

200 Series Smart Switches

2 200 Series Smart Switches

Welcome

Thank you for choosing the Cisco 200 Series Smart Switch, a Cisco Small

Business network communications device. This device is designed to be

operational right out-of-the-box as a standard bridge. In the default

configuration, it will forward packets between connecting devices after

powered up.

Package Contents

•Cisco SF 200-24, SF 200-24P, SF 200-48, SF 200-48P, SG 200-18, SG

200-26, SG 200-26P, SG 200-50, or SG 200-50P Smart Switch.

•Rackmount Kit.

•Power Cord.

•This Quick Start Guide.

•Product CD.

This guide will familiarize you with the layout of the smart switch and

describe how to deploy the device in your network. For additional

information, see www.cisco.com/smb.

Mounting the Cisco Switch

There are two ways to mount the switch:

• Set the switch on a flat surface.

• Mount the switch in a standard rack (1 rack unit high).

Do not mount the device in a location where any of the following conditions

exist:

High Ambient Temperature—The ambient temperature must not

exceed 104 degrees Fahrenheit (40 degrees Centigrade).

Reduced Air Flow—Both side panels must be unobstructed to prevent

overheating.

Mechanical Overloading—The device must be level, stable, and

secure to prevent it from sliding or shifting out-of-position.

Circuit Overloading—Adding the device to the power outlet must not

overload that circuit.

200 Series Smart Switches 3

Rack-Mount Placement

If your switch is rack-mount capable, it will come with a rack-mount kit. To

rack-mount the switch in any standard rack, attach the brackets to the

sides of the switch with the supplied hardware and secure the brackets.

CAUTION For stability, load the rack from the bottom to the top, with the

heaviest devices on the bottom. A top-heavy rack is likely to

be unstable and might tip over.

Connecting Network Devices

To connect the smart switch to the network:

STEP 1Connect the Ethernet cable to the Ethernet port of a computer,

printer, network storage, or other network device.

STEP 2Connect the other end of the Ethernet cable to one of the

numbered smart switch Ethernet ports.

The LED of the port lights if the device connected is active. Refer to

Features of the Cisco Small Business Smart Switch, page 7 for

details about the different ports and LEDs on each switch.

STEP 3Repeat Step 1 and Step 2 for each device you want to connect to

the smart switch.

NOTE Cisco recommends using Cat5 or better cable for Gigabit

connectivity. When you connect your network devices, do not exceed

the maximum cabling distance of 328 feet (100 meters). It can take up to

one minute for attached devices or the LAN to be operational after they

are connected. This is normal behavior.

Power over Ethernet Considerations

If your switch is one of the Power over Ethernet (PoE) models, consider the

following power requirement:

•As a Power Sourcing Equipment (PSE) device, the switch can deliver a

maximum of 15.4 Watts per PoE port to a Powered Device (PD).

4 200 Series Smart Switches

PoE is available on the following ports:

Use the following table to determine the total power budget available for

all devices on your switch.

Configuring the Cisco Small Business

Smart Switch

Before You Begin

Verify that a computer with Microsoft Internet Explorer (version 6 or higher)

or Firefox (version 2.0 or higher) is available.

Accessing and Managing Your Switch Using the Web-

Based Interface

In order to access the switch with a web-based interface, you must know

the management IP address of the switch. The default configuration of the

switch is to use its factory default IP address of 192.168.1.254 until it has

obtained an IP address from a DHCP server, or it has been changed to a

static IP address.

When the switch is using the factory default IP address, its System LED

flashes continuously. When the switch is using a DHCP assigned IP

address or an administrator configured static IP address, the System LED

lights steady.

NOTE If the smart switch IP address is changed, either by a DHCP server

or manually, your access to the smart switch will be lost and you must

use the new IP address to configure the device.

To configure the smart switch:

STEP 1Power on the computer and the switch.

STEP 2Connect the computer to the switch. You can connect to the same

IP subnet as the switch by connecting them directly with an

Model Ports

SF 200-24P and SG 200-26P 1—6 and 13—18

SF 200-48P and SG 200-50P 1—12 and 25—36

Model Power Dedicated to PoE

SF 200-24P 100 Watts

SF 200-48P 180 Watts

SG 200-26P 100 Watts

SG 200-50P 180 Watts

200 Series Smart Switches 5

Ethernet cable, or by connecting to the same LAN where the

switch is located through other switches. You can also connect

your computer to the switch from another IP subnet through one or

more IP routers.

STEP 3Set up the IP configuration on your computer.

a. If the switch is using the default static IP address of

192.168.1.254, you must choose an IP address in the range of

192.168.1.1—192.168.1.253 that is not already being used by

another device.

b. If the IP addresses will be assigned by DHCP, make sure your

DHCP server is running and can be reached from the switch

and the computer. You might need to disconnect and

reconnect the devices for them to discover their new IP

addresses from the DHCP server.

NOTE Details on how to change the IP address on your computer

depend upon the type of architecture and operating system you are

using. See your computer’s local Help and Support functionality

and search for “IP Addressing.”

STEP 4Open a Web browser window. If you are prompted to install an

Active-X plug-in when connecting to the device, follow the

prompts to accept the plug-in.

STEP 5Enter the switch IP address in the address bar and press Enter. For

example, http://192.168.1.254.

The Smart Switch Login page

displays.

STEP 6Enter the login information:

Username is cisco

Default password is cisco (passwords are case sensitive)

STEP 7If this is the first time that you have logged on with the default

username and password, the

Change Password

page opens. Enter

a new administrator password and then click Apply.

CAUTION Make sure that any configuration changes that you made are

saved before exiting from the web-based interface by

clicking on the Save icon, then clicking Apply. Exiting before

you save your configuration will result in all changes being

lost.

The Getting Started window displays. You are now ready to configure the

switch. Refer to the

Cisco Small Business Smart Switch Administration

Guide

for further information.

6 200 Series Smart Switches

Troubleshoot Your Connection

If you cannot access your switch from the web-based interface, the switch

might not be reachable from your computer. You can test network

connections by using the ping command. The following section shows

how to use “ping” in a Windows environment:

STEP 1Open a command window by using Start > Run and enter cmd.

STEP 2At the Command window prompt enter ping and the smart switch

IP address. For example ping 192.168.1.254 (the default IP address

of the smart switch).

If you can reach the switch, you should get a reply similar to the

following:

Pinging 192.168.1.254 with 32 bytes of data:

Reply from 192.168.1.254: bytes=32 time<1ms TTL=128

If you cannot reach the switch, you should get a reply similar to the

following:

Pinging 192.168.1.254 with 32 bytes of data:

Request timed out.

Possible Causes and Resolutions

No Power:

Power up the switch and your computer if they are turned off.

Bad Ethernet connection:

Check the LEDs for proper indications. Check the connectors of the

Ethernet cable to ensure they are firmly plugged into the switch and

your computer.

Wrong or conflicting IP address:

Make sure that you are using the correct IP address of the switch. You

can verify the current IP address of the switch with your network

administrator. The System LED provides an indication of where the

switch received the IP address, see Section 4 for details.

Make sure that no other device is using the same IP address as the

switch.

No IP route:

If the switch and your computer are in different IP subnets, you need

one or more routers to route the packets between the two subnets.

200 Series Smart Switches 7

Unusually long access time:

Due to the spanning tree loop detection logic, adding new connections

might take 30 to 60 seconds for the affected interfaces and/or LAN to

become operational.

Features of the Cisco Small Business

Smart Switch

This section describes the exterior of the smart switches including ports,

LEDs, and connections. Not all models will have all of the features

described.

Ports

RJ-45 Ethernet Ports—Use these ports to connect network devices, such

as computers, printers, and access points, to the switch.

MiniGBIC (if present)—The miniGBIC (gigabit interface converter) ports are

connection points for miniGBIC modules, so the smart switch can uplink to

other switches by using optical fiber.

•MiniGBIC ports are compatible with Cisco miniGBIC modules MGBSX1,

MGBLH1, MGBLX1, MGBBX1, MFELX1, MFEFX1, and MFEBX1, as well as

other brands of miniGBIC modules.

• MiniGBIC interface is a combination port, shared with one other RJ-45

interface. When the MiniGBIC is active, the adjacent RJ-45 port is

disabled.

•The LEDs of the corresponding RJ-45 port flashes green to respond to

the miniGBIC interface traffic.

8 200 Series Smart Switches

LEDs

System LED—(Green) Lights steady when the switch is powered on, and

flashes when booting, performing self tests, and acquiring an IP address. If

the LED flashes amber, the switch has detected a hardware failure.

LINK/ACT LED—(Green) Located on the left of the port. Lights steady

when a link between the corresponding port and another device is

detected. Flashes when the port is passing traffic.

NOTE The System and LINK/ACT LEDs are on each model of the switch.

The following LEDs are only present on switch models that have those

capabilities:

PoE (if present)—(Amber) Located on the right of the port. Lights steady to

indicate that power is being supplied to a device attached to the

corresponding port.

100M LED (if present)—(Green) Located on the right of the port. Lights

steady when another device is connected to the port, is powered on, and a

100 Mbps link is established between the devices. When the LED is off, the

connection speed is under 100 Mbps or nothing is cabled to the port.

Gigabit LED (if present)—(Green) Located on the right of the port. Lights

steady when another device is connected to the port, is powered on, and a

1000 Mbps link is established between the devices. When the LED is off,

the connection speed is under 1000 Mbps or nothing is cabled to the port.

MiniGBIC (if present)—(Green) Located on the right of the port. Lights

steady when a connection is made through the shared RJ-45 port. Flashes

when the port is passing traffic.

Additional Features

The switch might also have a reset button. The switch can be reset by

inserting a pin or paper clip into the reset opening. See “Returning the

Device to the Factory Default Settings” for details.

200 Series Smart Switches 9

Back Panel

The power port is located on the back panel of the smart switch.

Returning the Device to the Factory

Default Settings

To use the Reset button to reboot or reset the smart switch, do the

following:

•Toreboot the smart switch, press the Reset button for less than 10

seconds.

•To restore the smart switch configuration to the factory default settings:

1. Disconnect the smart switch from the network or disable all DHCP

servers on your network.

2. With the power on, press and hold the Reset button for more than

10 seconds.

10 200 Series Smart Switches

Where to Go From Here

Support

Cisco Small Business Support

Community

www.cisco.com/go/smallbizsupport

Cisco Small Business Support

and Resources

www.cisco.com/go/smallbizhelp

Phone Support Contacts www.cisco.com/en/US/support/tsd_cisco_

small_business_support_center_contacts.html

Cisco Small Business Firmware

Downloads

www.cisco.com/go/smallbizfirmware

Select a link to download firmware for Cisco

Small Business Products. No login is required.

Downloads for all other Cisco Small Business

products, including Network Storage Systems,

are available in the Download area on

Cisco.com at www.cisco.com/go/software

(registration/login required).

Product Documentation

Cisco Small Business Smart

Switches

www.cisco.com/go/smallbizsmartswitches

200 Series Smart Switches

Quick Start Guide

www.cisco.com/en/US/docs/switches/lan/

csbss/sf20x_sg20x/quick_start/78-19501-

01.pdf

200 Series Smart Switches

Administration Guide

www.cisco.com/en/US/docs/switches/lan/

csbss/sf20x_sg20x/administration_guide/OL-

22849-01.pdf

Regulatory, Compliance, and

Safety Information

www.cisco.com/en/US/docs/switches/lan/

csbms/sfe2000/release/notes/

Class_A_Switches_RCSI.pdf

Warranty Information www.cisco.com/go/warranty

Cisco Small Business

Cisco Partner Central for Small

Business (Partner Login

Required)

www.cisco.com/web/partners/sell/smb

Cisco Small Business Home www.cisco.com/smb

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cisco Schalten Handbücher

Cisco

Cisco Catalyst C3850 Series Handbuch

Cisco

Cisco Nexus 9332PQ Handbuch

Cisco

Cisco MDS 9000 Series Installationshandbuch

Cisco

Cisco 2950 - Catalyst Switch Installationshandbuch

Cisco

Cisco ME 6500 Bedienungs- und Sicherheitshinweise

Cisco

Cisco IE 4000 Bedienungsanleitung

Cisco

Cisco IGX 8 Bedienungsanleitung

Cisco

Cisco Laserjet,Color Laserjet 3020 Gebrauchsanweisung

Cisco

Cisco CSS-11051-AC Handbuch

Cisco

Cisco 2950 - Catalyst Switch Bedienungsanleitung

Cisco

Cisco SRW2048 - Small Business Managed Switch Bedienungsanleitung

Cisco

Cisco Network Analysis Module 6000 Bedienungs- und Wartungsanleitung

Cisco

Cisco AJ732A - MDS 9134 Fabric Switch Bedienungsanleitung

Cisco

Cisco Catalyst 8510 Bedienungsanleitung

Cisco

Cisco 2975 - Catalyst LAN Base Switch Bedienungsanleitung

Cisco

Cisco Catalyst Series Switch 2940 Bedienungsanleitung

Cisco

Cisco Nexus 7000 Series Bedienungsanleitung

Cisco

Cisco Catalyst 9400 Series Betriebsanleitung

Cisco

Cisco Catalyst 4124 Bedienungs- und Sicherheitshinweise

Cisco

Cisco MDS 9148T Handbuch

Cisco

Cisco Nexus 7000 Series Bedienungsanleitung

Cisco

Cisco Catalyst 4500 Series Bedienungsanleitung

Cisco

Cisco WS-C3750-48PS-S Bedienungsanleitung

Cisco

Cisco SG350XG-2F10 Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung