Cisco 7330 Bedienungsanleitung

QUICK START GUIDE

Cisco Universal Small Cell 7330

Revised: November, 2013, 78-21441-03

Table of Contents

1About Your Small Cell

2Before You Begin

3Safety Instructions

4Connect Your Small Cell

5Mount Your Small Cell

Mounting on a Wall or Hard Ceiling

Mounting on a Suspended Ceiling

Mounting on a Suspended Ceiling Using an Existing

Bracket

Mounting in a Plenum Space

6Verify that Your Small Cell is Operating Correctly

7Declarations of Conformity and Regulatory Information

8Specifications

9Obtaining Documentation and Submitting a Service

Request

1 About Your Small Cell

The Cisco Universal Small Cell (USC) 7330 is an indoor small

cell that provides Wideband Code Division Multiple Access

(WCDMA) coverage and capacity to public areas where macro

networks are not cost-effective. The USC 7330 supports up to

16 active third-generation (3G) users and supports Band 2/5 for

the American market and Band 1 for the rest of the world.

Package Contents

Your Cisco USC 7330 small cell is shipped with the following:

•Power supply unit—European Union (EU) compatible type

plug for Band 1 and US compatible plug for Band 2/5.

Other plug types must be ordered separately.

•Suspended ceiling mount bracket—to mount the small cell

on a ceiling.

•Rail mounting accessory pack, including screws.

•Ethernet cable.

•This Quick Start Guide.

Figure 1 Cisco USC 7330 Top View

1Power LED

2Ethernet connection LED

3Status LED

4External antenna port

361429

2 Before You Begin

Consider where you want to install your new small cell. The

ideal location is:

•somewhere central, away from windows—this will allow

your small cell to provide the best possible coverage.

•at least one 30 cm (1 foot) from other wireless broadcasting

devices to avoid possible interference.

•where you can connect to your broadband router or cable

modem.

Decide whether you will mount your small cell on a wall or

ceiling, or whether you will place it on a desktop or other flat

surface.

3 Safety Instructions

Translated versions of the following safety warnings are

provided in Cisco USC 7330 Regulatory Compliance and

Safety Information, located on Cisco.com.

Warning

IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a

situation that could cause bodily injury. Before you

work on any equipment, be aware of the hazards

involved with electrical circuitry and be familiar

with standard practices for preventing accidents.

Use the statement number provided at the end of

each warning to locate its translation in the

translated safety warnings that accompanied this

device.

Statement 1071

SAVE THESE INSTRUCTIONS

Warning

Read the installation instructions before you

connect the system to its power source.

Statement

1004

Warning

Installation of the equipment must comply with

local and national electrical codes.

Statement 1074

Warning

This product relies on the building’s installation

for short-circuit (overcurrent) protection. Ensure

that the protective device is rated not greater than:

20A.

Statement 1005

Warning

Do not operate the unit near unshielded blasting

caps or in an explosive environment unless the

device has been modified to be especially

qualified for such use.

Statement 364

Warning

In order to comply with FCC radio frequency (RF)

exposure limits, antennas should be located at a

minimum of 7.9 inches (20 cm) or more from the

body of all persons.

Statement 332

Caution The fasteners you use to mount an access point on

a ceiling must be capable of maintaining a

minimum pullout force of 20 lbs (9 kg) and must

use all indented holes on the mounting bracket.

Caution This product and all interconnected equipment

must be installed indoors within the same building,

including the associated LAN connections as

defined by Environment A of the IEEE 802.af

Standard.

Note Your small cell is suitable for use in environmental air

space in accordance with section 300.22.C of the

National Electrical Code and sections 2-128,

12-010(3), and 12-100 of the Canadian Electrical

Code, Part 1, C22.1. You should not install the power

supply or power injector in air handling spaces.

Note Use only with listed ITE equipment.

4 Connect Your Small Cell

Figure 2 Cisco USC 7330 Connections

110/100 Base-T Ethernet port supporting PoE+

2Power port

3GPS port (available on Band 2/5 only)

361430

Step 1 Connect one end of the network cable to the small cell

Ethernet port and the other end to your broadband

router or cable modem.

Step 2 Connect the power adaptor to the power port and then

switch on at the mains.

Step 3 (Optional) If you have a Band 2/5 small cell, you can

connect a GPS antenna to the GPS port.

Step 4 (Optional) You can connect an external antenna. For

the USC7330-T1-K9, connect an external antenna for

the Sniff bands (Bands 3 and 8) to connector 5 and

connect the external antenna for Band 1 to connector 6

(Figure 2). For the USC7330-T2-K9, connect an

external antenna for Band 5 to connector 5 and connect

the external antenna for Band 2 to connector 6

(Figure 2).

4Reset button

52G external antenna port for the Band 1 small cell

(USC7330-T1-K9) or UMTS Band V external antenna port

for the Band 2/5 small cell (USC7330-T2-K9)

63G external antenna port for the Band 1 small cell

(USC7330-T1-K9) or UMTS Band II external antenna port

for the Band 2/5 small cell (USC7330-T2-K9)

Inhaltsverzeichnis

Andere Cisco Drahtloser Zugangspunkt Handbücher

Cisco

Cisco Aironet 1600 Series Kurzanleitung

Cisco

Cisco Catalyst 9136I Series Handbuch

Cisco

Cisco Meraki MR20-HW Bedienungsanleitung

Cisco

Cisco GR10-HW-EU Bedienungsanleitung

Cisco

Cisco Meraki MR20 Bedienungsanleitung

Cisco

Cisco 800 Series Bedienungsanleitung

Cisco

Cisco Aironet 1100 Series Bedienerhandbuch

Cisco

Cisco WAP121 Bedienungsanleitung

Cisco

Cisco AIR-AP352E2R - Aironet 350 - Wireless Access... Bedienungsanleitung

Cisco

Cisco Cisco Aironet Wireless LAN Client Bedienungsanleitung

Cisco

Cisco Aironet 1300 Series Bedienungsanleitung

Cisco

Cisco Linksys WAP610N Bedienungsanleitung

Cisco

Cisco Catalyst 9164 Series Bedienungsanleitung

Cisco

Cisco AIR-BR1310G-A-K9-R - Aironet 1310 Outdoor Access... Bedienungsanleitung

Cisco

Cisco Aironet 2800I Series Bedienungsanleitung

Cisco

Cisco AIR-CAP3502I-A-K9 Bedienungsanleitung

Cisco

Cisco Small Business AP541N Bedienungsanleitung

Cisco

Cisco Meraki MR46E Bedienungsanleitung

Cisco

Cisco 15454-GBIC-LX= - 1000 Mbps GBIC Expansion... Handbuch

Cisco

Cisco WET200 Wireless-G Business Ethernet Bridge Bedienungsanleitung

Cisco

Cisco WAP200 - Small Business Wireless-G Access... Bedienungsanleitung

Cisco

Cisco 1130AG - Aironet - Wireless Access Point Handbuch

Cisco

Cisco WAP4410N - Small Business Wireless-N Access... Bedienungsanleitung

Cisco

Cisco Aironet 1830 Series Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung

Draytek

Draytek VIGORAP 902 Bedienungsanleitung