Cisco Meraki MR42E Bedienungsanleitung
MR42E Installation Guide
The Cisco Meraki MR42E is a dual-band enterprise class 802.11ac cloud-managed access point with support for
external antennas. Designed for high capacity and high density, the MR42E meets the needs of the most demanding
environments. The access point also includes a third radio dedicated to optimizing the RF environment and securing the
airwaves along with a BLE radio for supporting IoT applications.
Package Contents
The MR42E package contains the following:
• MR42E Cloud-Managed Access Point
• Mount cradle including built-in level tool
1
• Drop ceiling mount kit
• Wall screws, wall screw anchors, and security screws
• Spare hardware
Understanding the MR42E
Your Meraki MR42E has the following features:
2
The mount cradle has the following features:
3
Security Features
The MR42E features multiple options for physically securing the access point after installation:
1. Security screw – The accessory kit includes screws that can be used to secure the access point to the mount
cradle. Engaging the security screw prevents accidental dislodging and theft.
2. ensington lock – The access point contains a hard point that allows it to be secured to any nearby permanent
structure using a standard ensington lock.
External Antenna Ports
The MR42E has 5 external antenna ports:
The ports labeled 2.4/5 is meant for client serving radios
The port labeled Scan is meant for scanning wireless channels
4
The port labeled IoT is meant for BLE applications
Ethernet Ports
The MR42E features a Gigabit Ethernet RJ45 port that accepts 802.3at and 802.3af power (labeled “Eth0, PoE”). This
port should be used for uplink to your WAN connection.
Power Source Options
The MR42E access point can be powered using either the Meraki AC Adapter, PoE Injector (both sold separately), or a
third-party PoE switch.
The MR42E will function in low power mode when powered by a 802.3af power source. While in low power mode, the
MR42E will disable its Air Marshal radio as well as two out of three transmit streams on the 2.4 Ghz band. Despite being
in low power mode, the device can still supply full 802.11ac capabilities.
Factory Reset Button
If the button is pressed and held for at least five seconds and then released, the MR42E will reboot and be restored to
its original factory settings by deleting all configuration information stored on the unit.
LED Indicators and Run Dark Mode
Your MR42E is equipped with a multi-color LED light on the front of the unit to convey information about system
functionality and performance:
• Orange - AP is booting (permanent Orange suggests hardware issue)
• Rainbow - AP is initializing/scanning
• Blinking Blue - AP is upgrading
• Green - AP in Gateway mode with no clients
• Blue - AP in Gateway mode with clients
• Blinking Orange - AP can't find uplink
5
The MR42E may be operated in “Run Dark” mode for additional security and to reduce the visibility of the access point.
In this mode, the LED will not be illuminated. This mode may be enabled through Meraki dashboard.
Pre-Install Preparation
You should complete the following steps before going on-site to perform an installation.
Configure Your Network in Dashboard
The following is a brief overview only of the steps required to add an MR42E to your network. For detailed instructions
about creating, configuring and managing Meraki wireless networks, refer to the online documentation
(documentation.meraki.com).
1. Login to http://dashboard.meraki.com. If this is your first time, create a new account.
2. Find the network to which you plan to add your APs or create a new network.
3. Add your APs to your network. You will need your Meraki order number (found on your invoice) or the serial
number of each AP, which looks like Qxxx-xxxx-xxxx, and is found on the bottom of the unit. You will also need
your Enterprise license key, which you should have received via email.
4. Go to the map / floor plan view and place each AP on the map by clicking and dragging it to the location where you
plan to mount it.
Check and Upgrade Firmware
To ensure your MR42E performs optimally immediately following installation, it is recommended that you facilitate a
firmware upgrade prior to mounting your MR42E.
1. Attach your MR42E to power and a wired Internet connection. See the "Power the MR42E" section for details.
2. The MR42E will turn on and the LED will glow solid orange. If the unit does not require a firmware upgrade, the
LED will turn either green (no clients associated) or blue (clients associated) within thirty seconds.
* If the unit requires an upgrade, the LED will begin blinking orange until the upgrade is complete, at which point the LED
will turn solid green or blue. You should allow at least a few minutes for the firmware upgrade to complete, depending on
the speed of your internet connection.
Check and Configure Firewall Settings
If a firewall is in place, it must allow outgoing connections on particular ports to particular IP addresses. The most
current list of outbound ports and IP addresses for your particular organization can be found here.
Assigning IP Addresses to MR42Es
All gateway MR42Es (MR42Es with Ethernet connections to the LAN) must be assigned routable IP addresses. These
IP addresses can be dynamically assigned via DHCP or statically assigned.
6
Dynamic Assignment
When using DHCP, the DHCP server should be configured to assign a static IP address for each MAC address
belonging to a Meraki AP. Other features of the wireless network, such as 802.1X authentication, may rely on the
property that the APs have static IP addresses.
Static Assignment
Static IPs are assigned using the local web server on each AP. The following procedure describes how to set the
static IP:
1. Using a client machine (e.g., a laptop), connect to the AP wirelessly (by associating to any SSID
broadcast by the AP) or over a wired connection.
2. If using a wired connection, connect the client machine to the MR42E either through a PoE switch or a
PoE Injector. If using a PoE switch, plug an Ethernet cable into the MR42E’s Ethernet jack, and the
other end into a PoE switch. Then connect the client machine over Ethernet cable to the PoE switch. If
using a PoE Injector, connect the MR42E to the “PoE” port of the Injector, and the client machine to the
“LAN” port.
3. Using a web browser on the client machine, access the AP’s built-in web server by browsing
to http://my.meraki.com. Alternatively, browse to http://10.128.128.128.
4. Click on the “Uplink Configuration” tab. Log in. The default login is the serial number (e.g. Qxxx-xxxx-
xxxx), with no password (e.g., Q2DD-551C-ZYW3).
5. Configure the static IP address, net mask, gateway IP address and DNS servers that this AP will use on
its wired connection.
6. If necessary, reconnect the AP to the LAN.
Static IP via DHCP Reservations
Instead of associating to each Meraki AP individually to configure static IP addresses, an administrator can
assign static IP addresses on the upstream DHCP server. Through “DHCP reservations,” IP addresses are
“reserved” for the MAC addresses of the Meraki APs. Please consult the documentation for the DHCP server to
configure DHCP reservations.
Collect Tools
You will need the following tools to perform an installation:
7
Collect Additional Hardware for Installation
You will need the following hardware to perform an installation:
Installation Instructions
Choose Your Mounting Location
A good mounting location is important to getting the best performance out of your MR42E access point. eep the
following in mind:
1. The antenna attached to the access point should have unobstructed line of sight to most coverage areas. For
example, if installing in an office filled with workspaces divided by mid-height cubicle walls, installing on the ceiling
or high on a wall would be ideal.
2. Power over Ethernet supports a maximum cable length of 300 ft (100 m).
3. If being used in a mesh deployment, the MR42E should have line of sight to at least two other Meraki devices. A
Cisco Partner can help ensure that your AP placement is ideal.
Install the MR42E
For most mounting scenarios, the MR42E mount cradle provides a quick, simple, and flexible means of mounting your
device. The installation should be done in two steps. First, install the mount cradle to your selected location. Then,
attach the MR42E to the mount cradle.
8
Attach the mount cradle
The MR42E mount cradle can be used to install your access point in a wide range of scenarios: wall or solid ceiling,
below a drop ceiling, on various electrical junction boxes.
The mount cradle contains a variety of hole patterns that are customized for each installation scenario. The mounting
template (included inbox with mount cradle) should be used to drill holes for wall mounts and also to identify the correct
hole patterns in the mount cradle that should be used for each type of mount. The included mount cradle
template shows the hole patterns that should be used for each type of mount.
Wall or Solid Ceiling Mount Using mount cradle
Using included wall anchors and screws, attach the mount cradle to your mounting wall or ceiling. It is
recommended that the MR42E be mounted to a wall or solid ceiling using the mount cradle for physical security
reasons.
Drop ceiling mount using mount cradle
To mount your MR42E on a drop ceiling T-rail, use the included drop ceiling mounting accessory kit. The
accessory kit can be used to mount to most 9/16”, 15/16” or 1 ½” T-rails. The kit contains:
• Drop ceiling mounting clips with set screws
• 6-32x4 mm screws
• 6-32x7 mm screws only used for recessed rail mount (uncommon)
9
• 2 rubber spacers
1. Attach the T-rail clips to the T-rail by rotating them and snapping them into place as shown. The black foam
pads should be compressed slightly after installation.
2. Using the dashed lines on the mount cradle template as a guide, set the proper spacing of the T-rail clips on
the T-rail.
3. Tighten the set screws on the T-rail clips to secure the clips using a 5/64”(2 mm) hex key.
10
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Cisco Drahtloser Zugangspunkt Handbücher
Cisco
Cisco WAP351 Bedienungsanleitung
Cisco
Cisco CISCO673-RF - 673 Router Bedienungsanleitung
Cisco
Cisco 1130AG - Aironet - Wireless Access Point Handbuch
Cisco
Cisco FM1000 Gateway Handbuch
Cisco
Cisco AIR-AP352E2R - Aironet 350 - Wireless Access... Bedienungsanleitung
Cisco
Cisco AIR-AP1542I-*-K Bedienungsanleitung
Cisco
Cisco Catalyst IW6300 Series Handbuch
Cisco
Cisco WAP300N Bedienungsanleitung
Cisco
Cisco 1130AG - Aironet - Wireless Access Point Bedienungsanleitung
Cisco
Cisco MERAKI MR72 Bedienungsanleitung
Cisco
Cisco Linksys Wireless-G WBP54GV2 Bedienungsanleitung
Cisco
Cisco Linksys WET610N Bedienungsanleitung
Cisco
Cisco WAP4410N - Small Business Wireless-N Access... Bedienungsanleitung
Cisco
Cisco Aironet 1300 Series Bedienungsanleitung
Cisco
Cisco Catalyst 9166 Series Handbuch
Cisco
Cisco 1262 Bedienungsanleitung
Cisco
Cisco MERAKI MR44 Bedienungsanleitung
Cisco
Cisco WAP4410N - Small Business Wireless-N Access... Bedienungsanleitung
Cisco
Cisco AIR-LAP1310G Bedienungsanleitung
Cisco
Cisco Aironet 1815T Bedienungsanleitung
Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken
D-Link
D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung
Ubiquiti
Ubiquiti NanoStation NSM2 Bedienungsanleitung
Aruba
Aruba IAP-335 Bedienungsanleitung
Advantek Networks
Advantek Networks AWN-AP-54MR Bedienungsanleitung
IP-COM
IP-COM AP355 Bedienungsanleitung
Buffalo
Buffalo AirStation WLA-L11G Bedienungsanleitung
