Cisco Aironet 1520 Series Bedienungsanleitung

GETTING STARTED GUIDE

Cisco Aironet 1520 Series Outdoor Mesh Access Points

INCLUDING LICENSE AND WARRANTY

1About this Guide

2Introduction to the Access Point

3Unpacking the Access Point

4Becoming Familiar With the Access Point

5Network Deployment Examples

6Preparing the Access Point

7Deploying the Access Point

8In Case of Difficulty

9Cisco 90-Day Limited Hardware Warranty Terms

1 About this Guide

This guide is designed to familiarize yourself with your Cisco Aironet 1520 Series Outdoor Mesh

Access Point and prepare it for use in your wireless network. Due to the complexity and number of

product options available, this guide does not provide detailed mounting and configuration

instructions. Those instructions can be found in the following documents:

•Cisco Mesh Networking Solution Deployment Guide

•Cisco Aironet 1520 Series Outdoor Mesh Access Point Hardware Installation Guide

•Cisco Aironet 1520 Series Access Point Power Injector Installation Instructions

Detailed configuration information can also be found in the Cisco wireless LAN controller

documentation for the controller and software release you are using. These and other documents are

available on Cisco.com. Follow these steps to access these documents:

Step 1 Browse to http://www.cisco.com.

Step 2 Click Support.A pop-up window appears.

Step 3 Click Wireless under View Information by Product Type. The Select Your Product or

Technology page appears.

Step 4 Enter Cisco Aironet 1520 Series in the Search for a Specific Product field and click Go. The

Cisco Aironet 1520 Series Introduction page appears.

Step 5 Choose the appropriate link for the documentation you want to view or download.

FCC Safety Compliance Statement

The FCC with its action in ET Docket 96-8 has adopted a safety standard for human exposure to radio

frequency (RF) electromagnetic energy emitted by FCC certified equipment. When used with approved

Cisco Aironet antennas, Cisco Aironet products meet the uncontrolled environmental limits found in

OET-65 and ANSI C95.1, 1991. Proper installation of this radio according to the instructions found

in this manual will result in user exposure that is substantially below the FCC recommended limits.

Declaration of Conformity with Regard to the EU Directive 1999/5/EC

(R&TTE Directive)

This declaration is only valid for configurations (combinations of software, firmware and hardware)

provided and/or supported by Cisco Systems. The use software or firmware not supported/provided

by Cisco Systems may result that the equipment is no longer compliant with the regulatory

requirements.

General Safety Guidelines

Warnings

Safety warnings appear throughout this guide in procedures that may harm you if performed

incorrectly. A warning symbol precedes each warning statement. The warnings below are general

warnings that are applicable to the entire guide. Specific warnings are included in the sections to which

they apply.

Translated versions of the safety warnings in this guide are provided in the Safety Warnings for

Cisco Aironet 1520 Series Outdoor Mesh Access Points document that accompanies this guide.

The translated warnings are also in Appendix A of the Cisco Aironet 1520 Series Outdoor Mesh

Access Point Hardware Installation Guide, which is available at cisco.com.

Warning

This warning symbol means danger. You are in a situation that could cause bodily injury.

Before you work on any equipment, be aware of the hazards involved with electrical

circuitry and be familiar with standard practices for preventing accidents. Use the

statement number provided at the end of each warning to locate its translation in the

translated safety warnings that accompanied this device.

Statement 1071

SAVE THESE INSTRUCTIONS

Warning

There is the danger of explosion if the battery is replaced incorrectly. Replace the battery

only with the same or equivalent type recommended by the manufacturer. Dispose of

used batteries according to the manufacturer’s instructions.

Statement 1015

Warning

Do not operate the unit near unshielded blasting caps or in an explosive environment

unless the device has been modified to be especially qualified for such use.

Statement 364

Warning

This equipment must be externally grounded using a customer-supplied ground wire

before power is applied. Contact the appropriate electrical inspection authority or an

electrician if you are uncertain that suitable grounding is available.

Statement 366

Warning

Read the installation instructions before connecting the system to the power source.

Statement 1004

Warning

Only trained and qualified personnel should be allowed to install, replace, or service

this equipment.

Statement 1030

Warning

Ultimate disposal of this product should be handled according to all national laws and

regulations.

Statement 1040

2 Introduction to the Access Point

The Cisco Aironet 1520 Series Outdoor Mesh Access Point (hereafter called the access point) is a

modularized outdoor access point designed for service in mesh networks. The access point can be

configured for one or two radio operation. Its 802.11b/g radio is used primarily for local access and

its 802.11a radio is used to provide wireless backhaul in the mesh. The access point is LWAPP

compliant based on Cisco’s Internetwork Operating System (IOS).

With two radios installed, the access point provides client access on its 802.11b/g radio, point-to-point

bridging, point-to-multipoint bridging and mesh networking on its 802.11a radio. With one radio

installed, the access point provides client access and wireless backhaul over its 802.11b/g radio.

The 5-GHz radio incorporates an Unlicensed National Information Infrastructure (UNII) radio

transceiver that can operate in either the Upper ISM 5.8-GHz frequency band or the 4.9-GHz Public

Safety Band. The 5-GHz radio on the access point is used for backhaul operations to the controller.

Note The 4.9-GHz Public Safety band requires a license and may be used only by qualified Public

Safety operators as defined in section 90.20 of the FCC rules.

The access point is a standalone unit that can be cable strand or tower mounted. The access point can

also operate as a relay node for other access points not directly connected to a wired network.

Intelligent wireless routing is provided by the patent-pending Adaptive Wireless Path Protocol

(AWPP). This enables each access point to identify its neighbors and intelligently choose the optimal

path to the wired network by calculating the cost of each path in terms of signal strength and the

number of hops required to get to a controller. The access point is configured, monitored, and operated

through a Cisco wireless LAN controller (hereafter called a controller) as described in the appropriate

Cisco Wireless LAN Controller Configuration Guide. The Cisco Mesh Networking Solution

Deployment Guide describes how to plan and initially configure the Cisco mesh network, which

supports wireless point-to-point, point-to-multipoint, and mesh deployments. The controllers use a

browser-based management system, a command-line interface (CLI), or the Cisco Wireless Control

System (WCS) network management system to manage the controller and the associated access points.

The access point is compliant with Wi-Fi Protected Access 2 (WPA2) and employs hardware-based

Advanced Encryption Standard (AES) encryption between wireless nodes to provide end-to-end

security.

3 Unpacking the Access Point

Note When you are unpacking the access point, do not remove the foam blocks attached to the

antenna connectors. The foam protects the antenna connectors during installation.

Follow these steps to unpack the access point:

Step 1 Open the shipping container and carefully remove the contents.

Step 2 Return all packing materials to the shipping container and save it.

Step 3 Ensure that all items listed in the “Package Contents” section are included in the shipment.

Check each item for damage. If any item is damaged or missing, notify your authorized Cisco

sales representative.

Package Contents

Each access point package contains the following items:

•One 1520 series access point

•Installed mounting plate (attached to the back of the access point)

•Ground lug with screw and washer

•Cisco Aironet 1520 Series Outdoor Mesh Access Point Mounting Instructions

•Translated Safety Warnings for Cisco Aironet 1520 Series Outdoor Mesh Access Points

•This guide

Optional Equipment

Depending on what you ordered, the following optional equipment may be part of your shipment:

•Cable modem (AIR-1520-CM-D2=)

•Battery, 6 amp hour (AIR-1520-BATT-6AH=)

•100BASE-BX10-U rugged SFP (GLC-FE-100BX-URGD=)

•Take-up reel for fiber cable (AIR-1520-FIB-REEL=)

•Pole mount kit (AIR-ACCMK1520=)

•Strand mount kit (AIR-ACCSMK1520=)

•Cable power module and supply (AIR-1520-CAB-PWR=)

•Band installation tool for pole mount kit (AIR-BAND-INS-TL=)

•Street light power tap (AIR-PWR-ST-LT-R3P=)

•AC power cord, 40 ft. (12.2 m) with North American plug (AIR-CORD-R3P-50NA=)

•Power injector (AIR-PWRINJ1500-2=)

•FIPS kit (AIRLAP-FIPSKIT=)

•Third-party lightning arrestors as required by local authorities

4 Becoming Familiar With the Access Point

The following illustrations show identify the access point connections. Before you begin the

installation process, use these illustrations to familiarize yourself with the access point.

Note The illustrations show all available connections for the configuration ordered. Unused

connections are capped to ensure the access point’s watertight integrity. Liquid tight

connectors are provided for all ports, which can be installed prior to or after deploying the

access point.

Figure 1 shows the access point bottom connectors.

Figure 1 Access Point Bottom Connectors

Note Antenna port 5 is not shown in this illustration. The port is reserved for future use and will

be located midway between antenna ports 4 and 6.

1AC power connector 5Power-over-Ethernet (PoE) Out Ethernet connector

2Reserved for future use 6LEDs

3Antenna port 6 7Antenna port 4

4Fiber optic connector 8PoE-In Ethernet connector

Figure 2 shows the access point left side and top connectors.

Figure 2 Access Point Left Side and Top Connectors

1Fiber connector 4Antenna port 2

2Cable Power over Cable (PoC) connector 5Antenna port 3

3Antenna port 1

Figure 3 shows the access point right side connections.

Figure 3 Access Point Right Side Connections

Radio Operation

The 2.4-GHz radio supports three antennas for multi-input, single output (MISO) operation. The

radio uses three receivers to support maximum ratio combining (MRC) to enhance receiver

performance. MRC is a technique that combines the signals from multiple receivers in a manner to

optimize the signals. MRC can provide up to 3 dB of increased receive signal strength.

The access point does not support both radios configured for backhaul support.

1Ground screw holes 2DC power connector

External Antennas

Warning

In order to comply with radio frequency (RF) exposure limits, the antennas for this

product should be positioned no less than 6.56 ft (2 m) from your body or nearby persons.

Statement 339

Warning

Do not locate the antenna near overhead power lines or other electric light or power

circuits, or where it can come into contact with such circuits. When installing the

antenna, take extreme care not to come into contact with such circuits, because they

may cause serious injury or death. For proper installation and grounding of the antenna,

please refer to national and local codes (for example, U.S.:NFPA 70, National Electrical

Code, Article 810, Canada: Canadian Electrical Code, Section 54).

Statement 1052

Warning

Only trained and qualified personnel should be allowed to install, replace, or service this

equipment.

Statement 1030

The access point is equipped with three N-type radio frequency (RF) connectors (antenna ports 1, 2,

and 3) on the top of the unit for external antennas to support multiple input single output (MISO)

operation as shown in Figure 1. The access point also has three N-type RF connectors (antenna ports

4, 5, and 6) on the bottom of the unit for external antennas as shown in Figure 2. When using the

optional Cisco compact omnidirectional antennas, the 2.4- and 5-GHz antennas connect directly to

the access point. The Cisco omnidirectional antennas use vertical polarization.

The access point can also be equipped with specific third-party external antennas (see Table 1), subject

to local regulatory requirements. If you install third-party antennas, be sure to install them with all

waterproofing steps recommended by the third-party manufacturer. For additional information, see

the documentation shipped with the antenna.

Note The FCC limits the amount of power this device can transmit. Power transmitted is a

combination of the amplification of the signal and the antenna gain. The access point has been

designed to operate with the antennas listed below having a maximum gain of 8 dBi for

2.5-GHz and 17 dBi for 5-GHz antennas. Antennas not included in this list or having a higher

gain are strictly prohibited for use with the access point. The required antenna impedance is

50 ohms.

Andere Handbücher für Aironet 1520 Series

Inhaltsverzeichnis

Andere Cisco Drahtloser Zugangspunkt Handbücher

Cisco

Cisco 1130AG - Aironet - Wireless Access Point Handbuch

Cisco

Cisco Aironet 1200 Series Bedienungsanleitung

Cisco

Cisco Cisco Aironet Wireless LAN Client Bedienungsanleitung

Cisco

Cisco Catalyst 9124AX Series Handbuch

Cisco

Cisco Linksys WAP54G LA Bedienungsanleitung

Cisco

Cisco Mesh Access Points Kurzanleitung

Cisco

Cisco Meraki MR70 Bedienungsanleitung

Cisco

Cisco Aironet 2600 Series Bedienungsanleitung

Cisco

Cisco aironet 2800 series Kurzanleitung

Cisco

Cisco AIR-AP1832I K9C Series Bedienungsanleitung

Cisco

Cisco AIR-LAP1310G Bedienungsanleitung

Cisco

Cisco Aironet 1250 Series Bedienungsanleitung

Cisco

Cisco AIR-AP1121G-E-K9 Handbuch

Cisco

Cisco WAP121 Bedienungsanleitung

Cisco

Cisco Aironet 700W Series Bedienungsanleitung

Cisco

Cisco WAP321 Bedienungsanleitung

Cisco

Cisco WAP121 Bedienungsanleitung

Cisco

Cisco Aironet 1200 Series Installations- und Betriebshandbuch

Cisco

Cisco Catalyst Wireless 9163E Bedienungsanleitung

Cisco

Cisco Meraki MR36-HW Handbuch

Cisco

Cisco Aironet 1240AG Series Handbuch

Cisco

Cisco Aironet 1400 Series Bedienungsanleitung

Cisco

Cisco Wap581 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung

Draytek

Draytek VIGORAP 902 Bedienungsanleitung