Cisco Aironet 1810W Series Bedienungsanleitung

GETTING STARTED GUIDE

Cisco Aironet 1810W Series Access Points

First Published: June 02, 2016

Last Modified: August 3, 2022

1About this Guide

2About the Access Point

3Safety Instructions

4Unpacking the AP

5Ports and Connectors on the AP

6Preparing the AP for Installation

7Installation Overview

8Performing a Pre-Installation Configuration

9Mounting the Access Point

10 Powering the Access Point

11 Configuring and Deploying the Access Point

12 Checking the Access Point LEDs

13 Miscellaneous Usage and Configuration Guidelines

14 Related Documentation

15 Declarations of Conformity and Regulatory Information

1 About this Guide

This guide provides instructions on how to install and configure your Cisco Aironet 1810W series

access points. This guide also provides mounting instructions and limited troubleshooting procedures.

The Aironet 1810W series access point is abbreviated as AP in this document.

2 About the Access Point

The Cisco Aironet 1810W series access point is an 802.11 a/b/g/n/ac (Wave 2) access point, with

internal antennas.

The Cisco Aironet 1810W has multiple mounting options to standard junction boxes. The AP can be

vertically mounted on a wall or on a desk/horizontal surface using the optional cradle kit. Physical

security is offered with the included Torx screw and the option to add a Kensington lock.

The AP supports 2.4 GHz 2x2 802.11 b/g/n MU-MIMO and 5 GHz 2x2 802.11 a/n/ac (Wave 2)

MU-MIMO applications simultaneously.

Access Point Features

The features of the 1810W series access points are:

•Supported mode(s) of operation:

–

Centralized

•Radio features supported are:

–

2.4 GHz and 5 GHz concurrent radios

–

2.4GHz radio with 2TX x 2RX and 2 spatial steams

–

5GHz radio with 2TX x 2RX and 2 spatial steams

–

802.11ac based Transmit Beamforming

–

Quality of Service (QoS)

–

Radio Resource Management (RRM)

–

Rogue Detection

–

BandSelect

–

Integrated Bluetooth LE 4.1 radio for location and asset tracking.

•The AP supports the following hardware external interfaces:

–

Three local GigE Ethernet Ports, one uplink GigE port, and one passive pass-through RJ45

port.

–

One 10/100/1000BASE-T PoE uplink port.

–

RS-232 management console interface through RJ-45.

Note The AP may face issues while booting if you use an unterminated console cable (not

plugged into any device or terminal) or a console cable that is more than one meter in

length.

–

Three 10/100/1000BASE-T ports (local Ethernet ports), one of which also serves as a PoE-Out

port.

The PoE-Out port provides 802.3af power when the AP is powered by Cisco local power

supply (AIR-PWR-D=) and ~6.5W power when the AP is powered by 802.3at power. The

PoE-Out port does not provide any power output when the AP is powered by 802.3af power.

–

DC power connector.

–

One RJ-45 passive pass-through port (back to bottom).

–

Mode button. For information on how to use the Mode button, see “Using the Mode Button”

section on page 36.

–

One multi-color LED status indicator for the AP status. LEDs are also present to indicate

per-port status for local the Ethernet ports. For information, see the “Checking the Access

Point LEDs” section on page 33.

–

Three local Gigabit Ethernet ports available to securely connect wired devices to the network.

•Two integrated 2.4 GHz/5 GHz dual-band antennas located on the sides of the 1810W access

point under the top housing. Peak antenna gain is approximately 2 dBi and 4 dBi in the 2.4 GHz

and 5 GHz bands respectively.

A full listing of the access point's features and specification are provided in the Cisco Aironet 1810W

Series Access Point Data Sheet, at the following URL:

http://www.cisco.com/c/en/us/products/collateral/wireless/aironet-1810w-series-access-points/datashe

et-c78-736869.html

Access Point Model Numbers and Regulatory Domains

The Cisco Aironet 1810W series access point comes in the model number format AIR-AP1810W-x-K9.

The ‘x’ in the model number is a placeholder for the regulatory domain. For information on supported

regulatory domains, see the following page:

http://www.cisco.com/go/aironet/compliance

3 Safety Instructions

Translated versions of the following safety warnings are provided in the translated safety warnings

document that is shipped with your access point. The translated warnings are also in the Translated

Safety Warnings for Cisco Aironet Access Points, which is available on Cisco.com.

Warning

IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury.

Before you work on any equipment, be aware of the hazards involved with electrical

circuitry and be familiar with standard practices for preventing accidents. Use the

statement number provided at the end of each warning to locate its translation in the

translated safety warnings that accompanied this device.

Statement 1071

SAVE THESE INSTRUCTIONS

Warning

Read the installation instructions before you connect the system to its power source.

Statement 1004

Warning

Installation of the equipment must comply with local and national electrical codes.

Statement 1074

Warning

This product relies on the building’s installation for short-circuit (overcurrent)

protection. Ensure that the protective device is rated not greater than:

20A.

Statement 1005

Warning

Do not operate your wireless network device near unshielded blasting caps or in an

explosive environment unless the device has been modified to be especially qualified for

such use.

Statement 245B

Caution The fasteners you use to mount an access point on a ceiling must be capable of

maintaining a minimum pullout force of 20 lbs (9 kg) and must use a minimum of 4 holes

on the mounting bracket, or a minimum of 2 holes when mounting on a network box.

Caution This product and all interconnected equipment must be installed indoors within the same

building, including the associated LAN connections as defined by Environment A of the

IEEE 802.3af/at Standard.

Note The access point is suitable for use in environmental air space in accordance with section

300.22.C of the National Electrical Code and sections 2-128, 12-010(3), and 12-100 of the

Canadian Electrical Code, Part 1, C22.1. You should not install the power supply or power

injector in air handling spaces.

Note Use only with listed Information Technology Equipment (ITE) equipment. For more

information on ITE equipment, refer to article 645 of the latest National Electrical Code

(NEC).

4 Unpacking the AP

To unpack the access point, follow these steps:

Step 1 Unpack and remove the access point and the mounting accessories, from the shipping box.

Step 2 Return any packing material to the shipping container and save it for future use.

Step 3 Verify that you have received the items listed below. If any item is missing or damaged, contact

your Cisco representative or reseller for instructions.

–

The access point

–

Mounting bracket AIR-AP-BRACKET-W2=

–

Torx security screw and mylar label to cover the screw

The following accessories can be ordered separately from Cisco:

•Spacer kit AIR-AP1810W-KIT=, includes spacer and RJ-45 jumper cable.

•Cradle kit AIR-OEAP1810-CRD=, includes back cover and RJ-45 jumper cable.

•Cisco local power supply AIR-PWR-D=.

•Physical security kit AIR-SEC-50=, which includes 50 security screws used to secure the access

point onto the wall-mounting bracket, 50 RJ-45 block-out plugs and 2 unlock keys for blocking

physical access to the RJ45 Ethernet ports.

5 Ports and Connectors on the AP

Figure 1 Face of the AP

Location of the Status LED, along with ports

and connectors, on the base of the AP 2

Location of the 48V DC port on the left side

of the AP

354635

Figure 2 Base of the AP with the Ports and Connectors

Note A physical security kit AIR-SEC-50=, which is sold separately, includes RJ-45 block-out plugs

and two unlock keys using which you can restrict physical access to the Ethernet and console

Location of the concealed Status LED. You

can see the LED only when it lights up. 4

LAN port 3.

Console port.

The AP is shipped with an RJ-45 block-out

plug in this port. You can get an unlock key

for this by ordering physical security kit

AIR-SEC-50=. 5

LAN port 2.

Passive Pass-Through port.

It is an RJ-45 port, from the base of AP to the

back of the AP.

PSE / LAN port 1.

This port provides 802.3af/at Power

Sourcing Equipment (PSE) PoE-Out power

on the LAN 1 Ethernet interface. With

802.3at input the PoE-Out is 6.95W (Class

2).With DC input the PoE-Out is 12.95W

(Class 0).

354633

2 3 4 5 6

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cisco Drahtloser Zugangspunkt Handbücher

Cisco

Cisco FM1000 Gateway Handbuch

Cisco

Cisco 500 Series Bedienerhandbuch

Cisco

Cisco Linksys Wireless-G WBP54GV2 Bedienungsanleitung

Cisco

Cisco WAP571E Bedienungsanleitung

Cisco

Cisco CISCO673-RF - 673 Router Bedienungsanleitung

Cisco

Cisco Meraki CW9163E Bedienungsanleitung

Cisco

Cisco AIR-AP1232AG-A-K9 - Aironet 1230AG - Wireless Access... Bedienungsanleitung

Cisco

Cisco AIR-AP1220B-A-K9 - Aironet 1200 - Wireless Access... Handbuch

Cisco

Cisco Meraki MR28 Bedienungsanleitung

Cisco

Cisco WAP4410N - Small Business Wireless-N Access... Bedienungsanleitung

Cisco

Cisco AT&T U-VERSE VEN401 Bedienungsanleitung

Cisco

Cisco Aironet 1530 Series, 1532 Bedienungsanleitung

Cisco

Cisco WAP371 Bedienungsanleitung

Cisco

Cisco IW3702 Bedienungsanleitung

Cisco

Cisco Aironet OfficeExtend AIR-OEAP602I-E-K9 Bedienungsanleitung

Cisco

Cisco MERAKI MR72 Handbuch

Cisco

Cisco WAP121 Bedienungsanleitung

Cisco

Cisco Wap581 Bedienungsanleitung

Cisco

Cisco WAP121 Bedienungsanleitung

Cisco

Cisco WAP125 Bedienungsanleitung

Cisco

Cisco Aironet 1400 Series Handbuch

Cisco

Cisco Digistar EoC Bedienungsanleitung

Cisco

Cisco MR18 Bedienungsanleitung

Cisco

Cisco WAP131 Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung

Draytek

Draytek VIGORAP 902 Bedienungsanleitung