Cisco WAP571 Bedienungsanleitung

Quick Start Guide

Cisco WAP571 Wireless-AC/N Premium Dual

Radio Access Point with PoE

1 Cisco WAP571 Wireless Access Point

Welcome

Thank you for choosing the Cisco WAP571 Wireless-AC/N Premium Dual

Radio Access Point with PoE. The Cisco WAP571 is an indoor dual radio

802.11ac + 802.11n access point.

This guide is designed to familiarize you with the general layout of the

access point, describe how to deploy the device in your network, and

describe how to configure the device. Your access point has more features

and functionality than what is described in this guide. For additional

information, see the Administration Guide. A link to the Administration

Guide is found in Where to Go From Here, page 12.

Package Contents

•Wireless Access Point

•Mounting kit

•This Quick Start Guide

•Ethernet cable

•Pointer Card with China RoHS

•Technical Support Contacts

•EU Directives 1999/5/EC Compliance Information (for EU SKU only)

Before You Begin

Before you begin the installation, make sure that you have the following

equipment and services:

•A computer with browser support for:

– Internet Explorer v7.0 or later

– Chrome v5.0 or later

– Firefox v3.0 or later

–Safariv3.0orlater

•Tools for installing the hardware

•One or more Ethernet network switches with PoE

Cisco WAP571 Wireless Access Point 2

Cisco WAP571 Wireless-AC/N Premium

Dual Radio Access Point with PoE Setup

Features

Front Panel

The front panel of the device consists of a single system LED. For a full

description of the colors of the light and its indications, see Verifying the

Hardware Installation, page 6.

A Kensington lock slot is found above the light.

Back Panel

The back panel of the device has two RJ-45 Ethernet ports. Facing the

back of the device, the right port (labeled “ETH0/PD”) is an 802.3at &

802.3af Power over Ethernet (PoE) port which is used to power your

device. The left port (labeled “ETH1”) is a general Gigabit Ethernet LAN

interface. Both are auto-sensing, Gigabit Ethernet (802.3) ports used to

connect your WAP devices to network devices, such as computers,

routers, or switches. We strongly recommend that you use a Category

5e or better cable for Gigabit connectivity.

The side panel of the device has a Reset button. See Rebooting the

Devices or Returning them to their Factory Default Settings, page 10

for information on the Reset button.

Default Setting

If you are using a Cisco RV Series router, the default range for the DHCP

assigned address is from 192.168.1.100 to 192.168.1.254. Any device

connecting to the same LAN will be assigned an IP address in this range.

If your network does not have an existing DHCP server, the WAP571 will

start a DHCP server for WLAN stations and stop the DHCP client when

WAP571 is in factory default. The DHCP server will assign the IP address

from 192.168.1.20 to 192.168.1.100.

Parameter Default Value

Username cisco

Password cisco

LAN IP Address DHCP address assigned

by server

Fallback LAN IP 192.168.1.245

Subnetwork Mask 255.255.255.0

3 Cisco WAP571 Wireless Access Point

Mounting the Cisco WAP571 Wireless-AC/

N Premium Dual Radio Access Point with

PoE Setup

You can place your access point on a desktop, or mount it on a wall or

ceiling.

Placement Tips

• Ambient Temperature—To prevent the access point from overheating,

do not operate it in an area that exceeds an ambient temperature of

104°F (40°C).

•AirFlow—Both side panels have vents that must be unobstructed to

prevent overheating.

• Mechanical Loading—The device should be level, stable, and secure

to prevent it from sliding or shifting out of position.

Wall and Ceiling Mounting

The Cisco WAP571 device can be wall or ceiling-mounted. A mounting kit

is packaged with your device. The kit is designed to install your device to

the wall or the ceiling.

The mounting bracket has some flexibility so that you can reuse existing

holes drilled for a Cisco WAP551 or WAP561 device. The installer can

remove the Cisco WAP551 or WAP561 and mount the Cisco WAP571.

The dimensions for the mount kit screws are as follows:

1.31 to .33 in

(7.8 to 8.3 mm)

2.86 to .88 in (21.8

to 22.3 mm)

3.22 to .24 in

(5.5 to 6.0 mm)

4.69 to .72 in

(17.5 to 18.2

mm)

196243

Cisco WAP571 Wireless Access Point 4

WARNING Insecure mounting might damage the device or cause injury.

Cisco is not responsible for damages incurred by insecure wall

or ceiling mounting.

To mount the Cisco WAP 571 device to a wall or ceiling:

STEP 1Determine where you want to mount the device. Verify that the

surface is smooth, flat, dry, and sturdy.

STEP 2Drill two pilot holes into the surface 2.75 inches (70 mm) apart for

your Cisco WAP device.

STEP 3Insert a screw into each hole, leaving a gap between the surface

and the base of the screw head.

STEP 4Place the upper slots of the bracket over the screws, adjust the

screws accordingly, and slide the bracket down until the screws fit

snugly into the slots.

STEP 5Using the bracket as a template, drill two more holes for the lower

screws.

STEP 6Insert a screw into each lower hole.

STEP 7Slide the WAP device into the bracket, placing the cable through

the break-out tab found in the back of the bracket.

Connecting the Cisco WAP571 Wireless-

AC/N Premium Dual Radio Access Point

with PoE Setup

The WiFi default SSID is “Cisco SB-Setup” with the passphrase “cisco123”

in WPA2-PSK AES. This wireless default configuration will not allow traffic

between WiFi and Ethernet; users will need to go through the setup wizard

to resume the traffic between WiFi and Ethernet.

The user can also perform the initial configuration using a wired Ethernet

connection.

To connect the device to the wired network:

STEP 1Connect the Ethernet cable to the Ethernet port of a PoE switch.

STEP 2Connect the other end of the network Ethernet cable to the

Ethernet port (PoE) of the wireless access point.

5 Cisco WAP571 Wireless Access Point

NOTE WAP571 bundles the two Ethernet ports to be link

aggregation mode. If the two Ethernet ports have been connected

at the same time, the link partner must also support link

aggregation.

After installation, all lights should be active. Refer to Verifying the

Hardware Installation, page 6 for details about the different lights on each

switch.

Cisco WAP571 Wireless Access Point 6

Verifying the Hardware Installation

To verify the hardware installation, complete the following tasks:

•Check the cable connections.

•Check the state of the indicator lights.

NOTE If you need help resolving a problem, visit the Cisco Support

Community at www.cisco.com/go/smallbizsupport.

Label Activity Description

Power Off The WAP571 is out of power.

Solid (Green) The Cisco WAP571 is normal; no wireless

client connected.

Solid (Blue) The Cisco WAP571 is normal; at least one

wireless client connected.

Flashing (Blue) The Cisco WAP571 is upgrading the firmware.

Solid (Red) The Cisco WAP571 fails to boot with both

firmware images.

LAN Off No Ethernet link; FE Ethernet link is active or

10Mbps.

Solid Green GE Ethernet link is active.

Flashing Green The WAP 571 is transmitting or receiving data.

7 Cisco WAP571 Wireless Access Point

Getting Started with the Configuration

To configure the wireless access points, you can either use Ethernet or

wireless. Please follow these steps to access the Wizard and then the

web-based configuration utility from your computer by Ethernet:

STEP 1Ethernet: Connect the wireless access point to the same network

(IP subnet) as your computer. The factory default IP address

configuration of the access points is DHCP. Make sure your DHCP

server is running and can be reached.

See Incorrect IP Address, page 10 for troubleshooting

information, or if you do not have a DHCP server.

Wireless: Search the wireless SSID "CiscoSB-Setup", and connect

to this SSID with the passphrase "cisco123".

STEP 2Locate the IP address of the wireless access point.

a. The wireless access points can be accessed and managed by

Cisco network tools and services including the Cisco FindIT

Network Discovery Utility that enables you to automatically

discover all supported Cisco devices in the same local

network segment as your computer. You can get a snapshot

view of each device or launch the product configuration utility

to view and configure the settings. For more information, see

www.cisco.com/go/findit.

b. The wireless access points are Bonjour-enabled and

automatically broadcast their services and listen for services

being advertised by other Bonjour-enabled devices. If you

have a Bonjour-enabled browser, such as Microsoft Internet

Explorer with a Bonjour plug-in, or the Apple Mac Safari

browser, you can find the wireless access point on your local

network without knowing its IP address.

You can download the complete Bonjour for Microsoft Internet

Explorer browser from Apple’s website by visiting:

http://www.apple.com/bonjour/

c. Locate the IP address assigned by your DHCP server by

accessing your router or DHCP server. See your DHCP server

instructions for more information.

STEP 3Launch a web browser, such as Microsoft Internet Explorer or

Mozilla Firefox.

STEP 4In the Address field, enter the default DHCP address and press the

Enter key.

Cisco WAP571 Wireless Access Point 8

STEP 5Enter the default user name of cisco and password of cisco in the

User Name and Password fields.

STEP 6Click Login. The Wireless Access Point Setup Wizard appears.

STEP 7Follow the Setup Wizard instructions to finish the WAP device

installation. We strongly recommend that you use the Setup

Wizard for the first installation.The Setup Wizard turns on the Wi-Fi

radio, which allows you to connect wirelessly. For more advanced

configurations, see the Administration Guide. A link to the

Administration Guide is found in Release the Reset button when

the system light turns on., page 11.

Congratulations, you can now start using your wireless access point.

Suggested Next Steps

Smart PoE

Smart PoE is designed for detecting the power level from the PSE (Power

Sourcing Equipment) side; it does not matter whether 802.3at or 802.3af

mode, the WAP571 will operate at the appropriate mode automatically.

Smart PoE ensures that the WAP571 remains functional once powered by

802.3af PSE, and intelligently to adjust operations below:

•Second Ethernet port disabled

•2.4-GHz 802.11n radio in 2x2:2 spatial-stream mode

•5-GHz 802.11ac radio operates without restrictions

In case of an error while installing, try the following troubleshooting

procedures described in this section:

Troubleshooting

If you cannot display the configuration utility, you can test the ability of the

computer to communicate with the device by using ping.

To u s e ping on a computer running Windows:

9 Cisco WAP571 Wireless Access Point

STEP 1Verify that the Cisco WAP571 is powered on and the lights indicate

the appropriate links.

STEP 2Locate the device’s IP address. While there are different ways to

locate your device’s IP address, this procedure uses Cisco FindIT.

a. If you have previously downloaded Cisco FindIT, open Internet

Explorer and launch Cisco FindIT. For more information on

downloading Cisco FindIT, see www.cisco.com/go/findit.

b. In the Cisco FindIT display, place your mouse over the device’s

name. The device IP address is displayed along with other

device information.

STEP 3Open a command window by choosing Start > Run and enter

cmd.

STEP 4At the command window prompt, enter ping and the device IP

address. In this example, we pinged 192.0.2.10.

If successful, you should get a reply similar to the following:

Pinging 192.0.2.10 with 32 bytes of data:

Reply from 192.0.2.10: bytes=32 time<1ms TTL=128

If it fails, you should get a reply similar to the following:

Pinging 192.0.2.10 with 32 bytes of data:

Request timed out.

Possible Cause of Installation Failure

No Power

•Power up the switch and your computer if they are turned off.

•Make sure your PoE switch is powered on and the lights indicate that

you have a link. See Verifying the Hardware Installation, page 6.

•Verify that the devices on your network are not plugged into a

switchable outlet.

Bad Ethernet Connection

•Check the state of the indicator lights. See Verifying the Hardware

Installation, page 6.

•Check the Ethernet cable to ensure that it is firmly connected to your

devices. Devices connected by the Ethernet cable can include the WAP

device, and routers, any switches, and your computer.

•Verify the connected switch has auto-negotiation enabled. The access

point and the switch need the same negotiation parameters set.

Andere Handbücher für WAP571

Inhaltsverzeichnis

Andere Cisco Drahtloser Zugangspunkt Handbücher

Cisco

Cisco Aironet 350 Series Handbuch

Cisco

Cisco Aironet 1815w Bedienungsanleitung

Cisco

Cisco MR18 Bedienungsanleitung

Cisco

Cisco Linksys WAP55AG Bedienungsanleitung

Cisco

Cisco aironet 2800 series Kurzanleitung

Cisco

Cisco Aironet 1200 Series Handbuch

Cisco

Cisco Catalyst 9166 Series Handbuch

Cisco

Cisco WAP361 Bedienungsanleitung

Cisco

Cisco GR10-HW Bedienungsanleitung

Cisco

Cisco Small Business WAP551 Bedienungsanleitung

Cisco

Cisco Meraki MR20 Bedienungsanleitung

Cisco

Cisco Linksys WAP55AG Bedienungsanleitung

Cisco

Cisco WAP200 - Small Business Wireless-G Access... Bedienungsanleitung

Cisco

Cisco Small Business WAP551 Bedienungsanleitung

Cisco

Cisco Aironet 1400 Series Handbuch

Cisco

Cisco AT&T U-VERSE VEN401 Bedienungsanleitung

Cisco

Cisco AIR-LAP1310G Bedienungsanleitung

Cisco

Cisco WAP121 Bedienungsanleitung

Cisco

Cisco WAP371 Bedienungsanleitung

Cisco

Cisco Aironet LAP1522 Handbuch

Cisco

Cisco Aironet 1520 Series Bedienungsanleitung

Cisco

Cisco AIR-AP1220B-A-K9 - Aironet 1200 - Wireless Access... Handbuch

Cisco

Cisco WAP121 Bedienungsanleitung

Cisco

Cisco AIR-AP1131G-A-K9 Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung

Draytek

Draytek VIGORAP 902 Bedienungsanleitung