Cisco UNIFIED COMMUNICATIONS UC320W Bedienungsanleitung
Quick Start Guide
Cisco Small Business
Unified Communications UC320W with FXO
Package Contents
•Unified Communications System
•Ethernet Network Cable
•Phone Cable
•Power Adapter
•Power Cord Retention Kit
•Quick Start Guide
•Phone Quick Reference Card
•Product CD-ROM
CAUTION Be sure to read Section 1 before installation.
2 Cisco UC320W Quick Start Guide
Welcome
Thank you for choosing the Cisco Small Business Unified Communications
Model UC320W. This guide describes how to install the equipment and
get started configuring the system.
Before You Begin
Minimum Requirements
•PC with web browser and Adobe Flash Player version 10.1 or later.
•Cisco SPA300 Series or Cisco SPA500 Series IP phones.
•Power adapters for the phones, as needed. Cisco SPA300 Series
phones always require power adapters. Cisco SPA500 Series phones
can receive power from a Power over Ethernet switch.
•Ethernet cables to connect IP phones and computers.
•Internet service.
•Voice over IP service or analog phone service.
Default Settings
NOTE Be sure to update to the latest firmware when asked at the
beginning of the installation.
CAUTION Before installing the Cisco UC320W into an existing network
with another DHCP server, refer to the Smart Designs (see links on
page 7). Carefully follow the instructions in this guide and in the UC320W
Simple Configuration Utility. IP address conflicts will result if two DHCP
servers are installed on your network.
Parameter Default Value
Username cisco
Password cisco
LAN IP
(Also the address for the web-
based configuration utility.)
192.168.10.1
DHCP Range
(DHCP server is enabled by default.)
192.168.10.100 to 149
Netmask 255.255.255.0
Voice VLAN 100
Default Voice VLAN Subnet 10.1.1.1
1
Cisco UC320W Quick Start Guide 3
Optional Equipment and Services
• Secure router for Internet access: Cisco recommends using a secure
router, such as a Cisco SRP500 Series Services Ready Platform or a
Cisco SA500 Series Security Appliance.
• Additional ports for IP phones and network devices: Connect a Cisco
ESW500 Series Power over Ethernet Switch to a LAN port. Other
switches may be used but may require configuration of VLAN and QoS
settings. Refer to the VLAN information in Default Settings, page 2. For
application notes, see the documentation links in Where to Go From
Here, page 7.
• Additional ports for analog devices and analog phone lines: Add up
to two Cisco SPA8800 IP Telephone Gateways with 4 FXO ports and 4
FXS ports. All added FXS ports count toward the 24 user maximum. A
device connected to the Cisco UC320W built-in FXS port (shown
below) is not counted.
•ISDNBRIservice:Install a Mediatrix™ 4400 Digital Gateway, Connect
both the Cisco UC320W and the BRI gateway to a secure router such as
Cisco SA500. For application notes, see the documentation links in
Where to Go From Here, page 7.
• Power cord retention kit: To prevent accidental removal of the power
cord, you can install the supplied power cord retention kit (not
illustrated). Remove the screw next to the power port. Connect the
clamp to the power cord. Insert the screw and install it onto the Cisco
UC320W. For detailed instructions, see the Cisco UC320W
administration guide.
NOTE For best results, install the latest firmware for any network devices,
such as routers and Ethernet switches, before proceeding.
Installing the Equipment and Configuring the
System
STEP 1Before you begin, gather the following information:
•Account information from your Internet Service Provider
•Phone numbers and account information for all phone services
•Names and phone settings for your users and groups
•Details for telephony features such as internal dialing, call
routing, and Auto Attendant
STEP 2Connect a network cable from the WAN port of the Cisco
UC320W to your Internet Service or Internet access device.
2
4 Cisco UC320W Quick Start Guide
STEP 3Connect the supplied power cord to the POWER port and to a
power outlet.
When the device is fully booted, the POWER/SYS light is steady
green.
STEP 4Connect your PC to a LAN port on the Cisco UC320W. Do not
connect any devices to the LAN ports at this point. You r P C
will receive an IP address in the 192.168.10.x range.
NOTE:
•You may need to adjust your PC’s connecting settings to
receive an IP address dynamically.
•For best results, set the screen resolution to 1024x768 or
higher.
STEP 5Start a web browser. In the Address bar, enter the IP address of the
Cisco UC320W (default 192.168.10.1).
STEP 6To log in, enter the username cisco and the password cisco.
Both the username and the password are case sensitive.
STEP 7When prompted, enter a new username and password. Neither
cisco nor admin is valid.
STEP 8Follow the instructions in the configuration utility to connect the
equipment and configure the system.
Notes:
•If you are installing the Cisco UC320W in a network with
another DHCP server, be sure to complete the Network
Topology step in the Getting Started menu.
•For best results, enable access to Cloud Services and accept
all available firmware updates.
Power
12VDC
LAN (10/100/1000)
WAN
(10/100/1000)
2341 1234
LINE (FXO) PHONE
(FXS) LINE
OUT LINE
IN
194793
UC 320W 192.168.10.x
Cisco UC320W Quick Start Guide 5
Getting to Know the Cisco UC320W
Installation Guidelines
•Ensure adequate air flow.
•Do not stack or place anything on top of the Cisco UC320W, or install it
on a hot surface.
•Ensure that the Cisco UC320W is secure and stable.
NOTE For mounting options, see the Cisco UC320W administration
guide.
Environmental Considerations
•Storage Temperature (sea level): -22° F to 140° F (-30° C to +60° C)
•Operating Temperature (sea level): 32°F to 104°F (0°C to 40°C)
•Relative Humidity (sea level): 5 to 95% RH (non-condensing)
Front Panel
1POWER/SYS On - Normal operation. Slow flashing - Booting up. Fast
flashing - Upgrading firmware. Off - No power.
2LAN On - Connected to a device. Flashing - Sending or receiving data.
Off- Not connected.
3WAN On - Connected to WAN. Flashing - Sending or receiving data. Off-
Not connected.
4PHONE (FXS) On - Service is available on the port, and the port is not in
use. Slow Flashing - Service is available and the attached phone is off
hook (in use). Off - The port is disabled.
5LINE (FXO) On - PSTN line loop detected. Slow Flashing - FXO port is in
use. Off - Not connected.
6WLAN On - Wireless radio is on. Flashing - Sending or receiving data.
Off - Disabled.
7VM On - Voice mail is enabled. Fast Flashing - System is full. Slow
flashing - Retrieving or recording voice mail. Off - Disabled.
8USB For future use.
3
195715
1 2 3 4 5 6 78
UC 320W
9
6 Cisco UC320W Quick Start Guide
Back Panel
Side Panel
9WPS On - WiFi Protected Setup succeeded. Slow flashing - Setup is in
progress. Fast flashing - Setup error. Off - Not in use. To configure a WiFi
connection by using WPS, make sure the wireless device is located near
the Cisco UC320W, and then press and hold this button until the WPS
light flashes.
1LINE (FXO) Connect phone lines for traditional phone service.
2PHONE (FXS) Connect an analog phone or fax machine.
3WAN Connect to the broadband network access device or to an uplink
port on an Ethernet switch that is connected to the Internet.
4LAN Connect IP phones and other network devices.
5LINE OUT Connect to an external speaker system.
6LINE IN Connect to an external music source for Music On Hold service
(optional).
7POWER Connect to a power source. Use only the provided power
adapter. Optionally, you can use the power cord retention clamp to
prevent accidental removal of the power cord. See instructions in the
Cisco UC320W administration guide.
1, 3 For future use.
2RESET - Using a paperclip or similar object, press this button briefly to
restart the unit. Press and hold for 10 seconds to restore the factory
default settings.
Power
12VDC
LAN (10/100/1000)
WAN
(10/100/1000)
2341 1234
LINE (FXO) PHONE
(FXS) LINE
OUT LINE
IN
1 2 3 4 5 6 7
195714
132
195716
Andere Handbücher für UNIFIED COMMUNICATIONS UC320W
5
Inhaltsverzeichnis
Andere Cisco WLAN-Router Handbücher
Cisco
Cisco RB-WRT54GS2 - Wireless-G Broadband Router Bedienungsanleitung
Cisco
Cisco CISCO861W-GN-A-K9 Bedienungsanleitung
Cisco
Cisco WRP400-G1 - Wireless Router Bedienungsanleitung
Cisco
Cisco WRT610N - Simultaneous Dual-N Band Wireless... Bedienungsanleitung
Cisco
Cisco Small Business RV315W Bedienungsanleitung
Cisco
Cisco BEFW11S4 Bedienungsanleitung
Cisco
Cisco 3230 Bedienungsanleitung
Cisco
Cisco Small Business WRP400 Bedienungsanleitung
Cisco
Cisco WRV210 - Wireless-G VPN Router Bedienungsanleitung
Cisco
Cisco 3825 Series Bedienungsanleitung
Cisco
Cisco QuickVPN - PC Bedienungsanleitung
Cisco
Cisco 3750G - Catalyst Integrated Wireless LAN... Bedienungsanleitung
Cisco
Cisco Linksys E1000 Bedienungsanleitung
Cisco
Cisco 881W - Integrated Services Router Wireless Handbuch
Cisco
Cisco 2000 Series Handbuch
Cisco
Cisco RB-WRT54GS2 - Wireless-G Broadband Router Bedienungsanleitung
Cisco
Cisco T-Mobile HIPORT+ Bedienungsanleitung
Cisco
Cisco Linksys WRT54GS Bedienungsanleitung
Cisco
Cisco Catalyst IR8140 Heavy Duty Series Handbuch
Cisco
Cisco 4402 - Wireless LAN Controller Leitfaden
