Citizen CH-432B Bedienungsanleitung

English Español

Português

DeutchItaliano Français

INSTRUCTION MANUAL

FOR

DIGITAL BLOOD PRESSURE MONITOR

MODEL CH-432B

- Eng 1 -

CH-432B

SYSTOLIC mmHg DIASTOLIC mmHg

PULSE/min

POWERSTART

After cleaning the cuff with a neutral detergent, lightly rinse

it with water and let it dry in the air. Hard rubbing or wash- ing in a washing machine will cause air leakage. Also, be

careful not to get water into the air hose.

CLEANING METHOD OF CUFF

GENERAL REMARKS

General Remarks on blood pressure

measurement

• If the cuff is to be deflated quickly, depress “POWER”

switch.

• The attached cuff is suited for an arm circumstance of 22cm to

32cm.

• When attaching the cuff, rubber cuff hose should be

placed on the inside of your arm on top of the arterial.

• Self measurement is no therapy! In no case may you

change the dosage of medication prescribed by your phy-

sician.

• In operation for blood pressure measurement, you should

urinate and should remain relatively still for 10 to 15 min-

utes prior to measurement.

• Exercise, eating and drinking, smoking, etc., prior to mea-

surement may affect the results.

• The blood pressure varies constantly throughout the day. Mea-

surement should be made regularly at the same time each day.

• Do NOT be impressed by the results of one measurement.

Keep a record of blood pressure variations. Many read-

ings tell a story.

• Emotional stress may tend to cause pressure to rise.

• This Product should not be used to monitor cardiac ar-

rhythmia.

For proper measurement of blood pressure

• Take a deep breath five or six time and then relax before

measuring blood pressure. If you are tense when taking

the measurement, you will not get a valid reading.

• Blood pressure will be elevated when you are in a worri-

some or irritated state, suffering from lack of sleep or

constipation, or after exercise or a meal.

NORMAL

HYPERTENSION

130 139 mmHg

mmHg

Diastolic Blood Pressure

Systolic Blood Pressure

HIGH NORMAL

- Eng 2 -

English Español

Português

DeutchItaliano Français

• Putting on the cuff is one of the most important tasks for

ensuring proper measurement of blood pressure. Wind

the cuff around the arm and tighten it so that one finger

may be inserted between the cuff and arm.

• Do NOT measure blood pressure after bathing or drink-

ing.

• When you feel like relieving yourself, you should do so

before measuring blood pressure.

• Measure blood pressure where the room temperature is

about 20˚C. Do NOT measure blood pressure when it is

too cold (below 10˚C) or too hot (above 40˚C) in the room.

• Do NOT measure blood pressure immediately after drink-

ing coffee or tea or smoking.

• Measure blood pressure with a relaxed and quiet pos-

ture. Keep the center of the cuff at the level of your heart,

and do NOT move your arm or talk during measurement.

• Do NOT keep on measuring so many times, as your arm

will have built up congestion of blood, and you will not

get a valid reading.

PRECAUTION FOR USE AND MAINTENANCE

Precautions for use

• If you suffer from heart disease, high blood pressure or

other circulatory disease, please consult your doctor first.

• If you feel abnormal pressure of the cuff during use or

any other irregularity, reduce the pressure by immedi-

ately switching off the power or removing the batteries

and consult the sales outlet where purchased.

• If you think the measured value is abnormal or if measur-

ing makes you feel unwell, discontinue use and consult

your doctor.

• Measurement of blood pressure may not be possible for

someone with a weak pulse or arrhythmia.

• Congestion, swelling, etc. may occur in some people.

• If blood pressure is measured repeatedly, an accurate re-

sult will not be achieved. An interval of about 10 minutes

should be allowed.

• The memory is erased if the batteries are removed for

replacement, etc. and a record should be kept of any nec-

essary data.

Precautions for maintenance

• Do NOT store the blood pressure monitor where it will be

exposed to direct sunlight, high temperature (over 60˚C),

low temperature (below –20˚C), high relative humidity

(over 95%) or in a dusty place.

• Do NOT expose the blood pressure monitor to under force

or vibration, or drop it.

• Remove the battery/batteries when not in use for a long pe-

riod.

• Do NOT disassemble the apparatus.

• Do NOT bend the cuff or air hose unnecessarily.

• NEVER wipe the blood pressure monitor with thinner or

benzene, as they may damage it.

- Eng 3 -

• When the monitor is very dirty, wipe it clean with a cloth

moistened with Sterilizing alcohol or a neutral detergent,

and then wipe it with a dry cloth. Do NOT use thinner or

benzene.

Nature and frequency of maintenance:

This products is designed for use over an extended period

of time; however, it is generally recommended that it be

inspected every two years to ensure proper function and

performance.

Protect the nature environment:

Please help protect natural environment by respecting na-

tional and/or local recycling regulations when disposing of

the batteries and the products at the end of their useful

lives.

Reference European standard:

This products complies with EC instructions 93/42/EEC

(Medical Device Directive) and with the following standards:

EN 1060-1: 1995 “Noninvasive Sphygmomanometers, Part

1 General Requirements” and EN 1060-3: 1997

“Noninvasive Sphygmo-manometers, Part 3 Supplemen-

tary Requirements for Electromechanical Blood-Pressure

Measuring Systems”.

Manufacturer:

Name: Premier Precision Ltd.

Address: Block E, G-H, 6th floor,

Phase 2, Yip Fat Factory Building,

73-75 Hoi Yuen Road,

Kwun Tong, Kowloon, Hong Kong

European Representative:

Name: WvW elektronische Geräte Vertrieb GmbH.

Address: Robert-Koch-Straße 20,

D-80538 München,

GERMANY

- Eng 4 -

English Español

Português

DeutchItaliano Français

- Eng 5 -

IDENTIFICATION OF PARTS

CH-432B

SYSTOLIC mmHgDIASTOLIC mmHg

PULSE/min

POWER START

Tube socket Systolic blood pressure

display section Diastolic blood pressure/

Pulse display section

Cuff

Cuff tube Air connector

Power/Start switch

Battry cover

- Eng 6 -

MEASUREMENTS

1. Attaching of Arm Cuff and Posture

During Measurement

Unfasten and open the cuff as shown in the figure.

Wind the arm cuff around the left upper arm tightly so that

bottom edge of the cuff is positioned about 1 –2cm above

the elbow joint.

•When you will wind the cuff, please wind the cuff next to

the skin of possible.

(If measurement is made by rolling the shirts or jacket

up over the arm, this will constrict the upper arm and

prevent accurate measurement.)

•Cuff tube should be placed on the inside of your arm as

figure.

•Please make sure that the cuff is fastened tightly. Note

that uneven cuff winding will prevent proper measure-

ments.

English Español

Português

DeutchItaliano Français

- Eng 7 -

Rest the elbow on a table so that the section of the upper

arm is at the height of the heart. Relax the lower arm across

the table and remain still, since movement - artifacts may

falsify the measuring result.

Make measurements in either a seated or reclining posture

with the palm turned upward.

Insert the air connector from the cuff into the tube socket

at the mainframe until it is tightly connected.

2. Carrying out the Measurement

Press the “POWER / START”switch.

When the “POWER / START”switch is pressed, the last-

measured systolic blood pressure and diastolic blood pres-

sure are displayed for about 2 seconds.

At the first measurement after battery replacement the mark

of “Q”is displayed for about 2 seconds.

SYSTOLIC mmHg DIASTOLIC mmHg

PULSE/min

SYSTOLIC mmHg DIASTOLIC mmHg

PULSE/min

- Eng 8 -

The pressure is automatically heightened to the level for

measurement of the blood pressure based on the last-mea-

sured systolic blood pressure.

At the first measurement after battery replacement the pres-

sure is heightened to 160mmHg.

If the level of the pressure is not enough, the pressure is

automatically heightened to the level for measurement of

the blood pressure again.

SYSTOLIC mmHg DIASTOLIC mmHg

PULSE/min

SYSTOLIC mmHg DIASTOLIC mmHg

PULSE/min

SYSTOLIC mmHg DIASTOLIC mmHg

PULSE/min

When the “POWER / START”switch pressing, the pressure

level for measurement will change at optional level over

160 mmHg.

But if the “POWER / START”switch is released before 160

mmHg, the pressure is heightened to 160mmHg.

When the pressure lowers by 15mmHg after pressuriza-

tion stops, the mark of “Q”is displayed.

If pulse is recognized, the pressure is shifted to the dias-

tolic blood pressure indicating section and change over,

synchronized with the pulse.

SYSTOLIC mmHg DIASTOLIC mmHg

PULSE/min

SYSTOLIC mmHg DIASTOLIC mmHg

PULSE/min

English Español

Português

DeutchItaliano Français

- Eng 9 -

SYSTOLIC mmHg DIASTOLIC mmHg

PULSE/min

SYSTOLIC mmHg DIASTOLIC mmHg

PULSE/min

When the measurement has been completed, the systolic

blood pressure, the diastolic blood pressure and the pulse

rate are alternately displayed and the air is discharged.

The systolic blood pressure and the diastolic blood pres-

sure are displayed for about 2 seconds and the pulse is

displayed for about 1 second.

The measured data are registered automatically, as long as

they are not error.

Whenapersonwithmaximumbloodpressureof170mmHg

or higher uses the unit for the first time, or after changing

batteries, measure blood pressure using the manual set-

ting. If the automatic pressure setting is used, it may not

work.

Automatic Pressure Setting

●This product automatically sets the pressure based on

the previous measurement, so you can easily measure

blood pressure by pressing one button without reset-

tingthepressureforeachmeasurement.Ifseveralpeople

use the unit, we recommend using the manual settings

as follows.

Manual Pressure Setting

●When several people use the unit, set the pressure value

manually. Please note that if the manual pressure set-

ting is not used, pressure will be automatically applied

based on the value set by the previous user.

If the previous user had a high pressure setting, that

high pressure will automatically be used for the current

user. If you feel pain in your arm, press the “POWER /

START”switch immediately to turn of the power.

1. Put the arm cuff around your arm, plug the air hose

into the unit, and keep your arm at the level of your

heart.

2. Keep the “POWER / START”switch depressed until

the pressure display shows the optimal pressure set-

ting. (The optimal pressure setting is about 40 mmHg

higher than your usual maximum blood pressure.)

3. When the pressure display reaches the optimal pres-

surevalue,releasethe“POWER /START”switch. When

the “POWER / START”switch is released pressuriza-

tionwillfinishandmeasurement willstart.Manual pres-

suresettingscanbeselectedbetween160mmHg-280

mmHg. If you release the “POWER / START”switch

before reaching 160 mmHg, the unit will pressurize to

160 mmHg. If the unit senses that the pressure is not

high enough, it will apply more pressure.

- Eng 10 -

3. Turn Power OFF

Press the “POWER / START”switch to turn off.

4. Subsequent Measurement

When a measurement is need again, 10 minutes, interval

is necessary between measurements.

5. Automatic Power OFF Function

If the unit is left without any operation after measure-

ment, an “Automatic Power-OFF Function”runs to turn

off the power after approximately 3 minutes. To continue

measurement, press the “POWER / START”switch again.

6. Battery Replacement

If the batteries are almost empty, the “ ” mark will be

displayed. In this case, batteries should be replaced with

new one.

Remove the battery cover at mainframe and replace four

type “AA”batteries.

Batteries are almost empty.

Batteries are normal.

Note: The memory data are erased when you replace the

batteries.

•The batteries that are included power the monitor. They

may not last as long as indicated.

•If manganese batteries are used at a low room tempera-

ture, such as in the winter or for other reasons, the bat-

teries may not function properly and you may not be able

to measure your blood pressure.

•Please dispose of used batteries properly to protect the

environmental.

Battery cover

Andere Handbücher für CH-432B

Inhaltsverzeichnis

Andere Citizen Blutdruckmessgerät Handbücher

Citizen

Citizen REF CH-657 Bedienungsanleitung

Citizen

Citizen CHU305 Bedienungsanleitung

Citizen

Citizen CH-608 Bedienungsanleitung

Citizen

Citizen CH-432B Bedienungsanleitung

Citizen

Citizen REF CH-308B Bedienungsanleitung

Citizen

Citizen CH-485E Bedienungsanleitung

Citizen

Citizen REF CHU503 Bedienungsanleitung

Citizen

Citizen CH-656C Bedienungsanleitung

Citizen

Citizen CH-432BS Bedienungsanleitung

Citizen

Citizen CH-311B Bedienungsanleitung

Citizen

Citizen CH-618 Bedienungsanleitung

Citizen

Citizen REF CH-491E Bedienungsanleitung

Citizen

Citizen CH-461C Bedienungsanleitung

Citizen

Citizen CH-403C Bedienungsanleitung

Citizen

Citizen CH607 Bedienungsanleitung

Citizen

Citizen CHUD514 Bedienungsanleitung

Citizen

Citizen CHU304 Bedienungsanleitung

Citizen

Citizen REF CH-456 Bedienungsanleitung

Citizen

Citizen CH-308B Bedienungsanleitung

Citizen

Citizen REF CH-657 Bedienungsanleitung

Citizen

Citizen CH-302B Bedienungsanleitung

Citizen

Citizen CH-650 Bedienungsanleitung

Citizen

Citizen CH-671F Bedienungsanleitung

Citizen

Citizen CHU305 Bedienungsanleitung

Beliebte Blutdruckmessgerät Handbücher anderer Marken

Little Doctor

Little Doctor LD7 Bedienungsanleitung

Microlife

Microlife WatchBP Office Targe Bedienungsanleitung

Omron

Omron M6W Handbuch

Mx Onda

Mx Onda MX-CP2395 Bedienungsanleitung

Braun

Braun VitalScan 1 Bedienungsanleitung

Little Doctor

Little Doctor LD-91 Bedienungsanleitung

Sanitas

Sanitas SBM 09 Bedienungsanleitung

A&D

A&D LifeSource UB-328 Bedienungsanleitung

König Electronic

König Electronic HC-BLDPRESS200 Bedienerhandbuch

Leicke

Leicke Sharon Bedienungsanleitung

Omron

Omron M6 Comfort Bedienungsanleitung

3B SCIENTIFIC

3B SCIENTIFIC U11395 Bedienungsanleitung

Soehnle

Soehnle SYSTO MONITOR 100 Bedienungsanleitung

Nasco Healthcare

Nasco Healthcare Simulaids Life/form LF01095U Referenzhandbuch

Microlife

Microlife WatchBP office Bedienungsanleitung

HoMedics

HoMedics MiBody 360 Bedienungsanleitung

ForaCare

ForaCare FORA P30 Plus Bedienungsanleitung

JOYTECH

JOYTECH DBP-6296B Bedienungsanleitung