Clarion Pro audio vrx 630 Gebrauchsanweisung

VRX630 43

English

Installation and Wire

connection manual

1. BEFORE STARTING................................................................43

2. PACKAGE CONTENTS............................................................43

3. GENERAL CAUTIONS.............................................................44

4. CAUTIONS ON INSTALLATION ..............................................44

5. INSTALLING THE MAIN UNIT .................................................45

6. REMOVING THE MAIN UNIT ..................................................47

7. CAUTIONS ON WIRING ..........................................................47

8. WIRE CONNECTION...............................................................48

9. SAMPLE SYSTEMS ................................................................50

■ Contents

VRX630

1. This set is exclusively for use in cars with a

negative ground 12 V power supply.

2. Read these instructions carefully.

3. Be sure to disconnect the battery “ ”termi-

nal before starting. This is to prevent short

circuits during installation. (Figure 1)

1Main unit

2Manuals

Owner’s manual & Installation manual

Warranty card

3Power supply lead

Bag for accessories of the main unit (No. 1)

Flat head screw (M5 ×8)............................4

Sems hexagonal bolt (M5 ×8)....................5

Bag for accessories of the main unit (No. 2)

Hook plate..................................................2

Cord clamp

Spacer

Special screw

6Universal mounting bracket

7Remote control unit

8Battery

(for remote control unit)

9Outer Escutcheon

0DCP Case

1. BEFORE STARTING

2. PACKAGE CONTENTS

Installation and Wire connection manual

44 VRX630

English

Installation and Wire

connection manual

1. Do not open the case.There are no user ser-

viceableparts inside.If you dropanythinginto

the unit during installation, consult your

dealer or an authorized CLARION service

centre.

2. Use a soft, dry cloth to clean the case.Never

use a rough cloth, thinner, benzine, or alco-

hol, etc. For tough dirt, apply a little cold or

warm water to a soft cloth and wipe off the

dirt gently.

1. Prepare all articles necessary for installing

the main unit before starting.

2. This model is used with the LCD panel slid

forwards (shell loading system). On some

types of cars, the LCD panel may touch the

dashboard or shift lever, in which case it can-

not be installed. Check that the set will not

hamper operation of the shift lever before

choosing the place of installation.(Figure 2)

3. Install the unit within 30°of the horizontal

plane. (Figure 3)

4. If you have to do any work on the car body,

such as drilling holes, consult your car dealer

beforehand.

5. Use the enclosed screws for installation.Us-

ing other screws can cause damage.

(Figure 4)

3. GENERAL CAUTIONS

4. CAUTIONS ON INSTALLATION

NNT

6. The source unit has mounting screw holes

for NISSAN(N marks)andTOYOTA(T marks)

vehicles.

VRX630 45

English

Installation and Wire

connection manual

■Universal Mount

1. Place the universal mounting bracket into the

instrument panel, use a screwdriver to bend

each stopper of the universal mounting

bracket inward, then secure the stopper as

shown in Figure 6.

2. Wire as shown in Section 8.

3. Insert the main unit into the universal mount-

ing bracket until it locks.

4. Mount the outer escutcheon so that all the

hooks are locked.

Notes:

1) Some car models require special mounting kits

for proper installation. Consult your Clarion

dealer for details.

2) Fasten the front stopper securely to prevent

the main unit from coming loose.

5. INSTALLINGTHE MAIN UNIT

• Console opening dimensions

Hole

Main unit

7-3/16" (182 mm)

2-1/16" (53 mm)

Screwdriver

Stoppers

Hole

Rear fastening hole (of vehicle)

Instrument panel

Rubber cap

Universal mounting bracket

Stoppers

2-Spring

Outer escutcheon

Note: Set the outer escutch-

eon so that its metallic

part on the back side

fits the upper edge of

the main unit.

Special Screw

46 VRX630

English

Installation and Wire

connection manual

This unit is designed for fixed installation in the

dashboard.

If the vehicle is equipped with a factory-installed

radio, install the main unit with the parts and

screws marked (∗). (Figure 8)

If the vehicle is not equipped with a factory-in-

stalled radio, obtain an installation kit to install

the main unit in the following procedure.

1. Remove the screws from both side of the

main unit. Then, at either side, lift the leaf

spring until the engaging claws are released

from the holes, and slide the spring to the

direction of arrow to remove it. Repeat the

■Fixed Mount (TOYOTA, NISSAN and other ISO/DIN equipped vehicles)

same for the other side to remove the springs

from the both sides. (Figure 7)

2. Secure the mounting brackets to the chassis

as shown in Figure 8. Holes are pre-tapped

for TOYOTA and NISSAN vehicles;modifica-

tion, such as drilling new holes, of the mount-

ing brackets may be required for other mod-

els.

3. Wire as shown in Section 8.

4. Secure the unit in the dashboard, and then

reassemble the dashboard and the centre

panel.

Note 1: In some cases, the centre panel may re-

quire some modification (trimming, filling,

etc.).

Note 2: If a hook on the installation bracket inter-

feres with the unit, bend and flatten it with a

nipper or a similar tool.

The parts and screws with this mark

are used to install radio or included in

the installation kit.

The screws with this mark are enclosed in

this set.

VRX630 47

English

Installation and Wire

connection manual

1. When the rear of the main unit has been se-

cured with the method shown in Figure 6

unfasten the special screw.

2. Remove the outer escutcheon.

3. Insert the hook plate between the spring and

the universal mounting bracket, fit tab

the spring into hole

of the hook plate, then

pull the main unit out by the hook plate. (In-

sert both the right and left edges of the hook

plate.) (Figure 9)

Note: Keep the hook plate.You cannot remove the

main unit without disengaging the hook plate.

6. REMOVINGTHE MAIN UNIT

1. Be sure to turn the power off before wiring.

2. Be particularly careful where you route the

wires.

Keep them well away from the engine, and

exhaust pipe, etc. Heat may damage the

wires.

3. If the fuse should blow, check to see if the

wiring is correct.

If it is, replace the fuse with a new one with

the same amperage rating as the original.

4. When any fuse is to be replaced, pull out the

fuse (15A) at the rear of the main unit and

put in a new one (Fig.10).

7. CAUTIONS ON WIRING

5. When connecting the ground lead, fasten the

ground lead (black) securely to a clean metal

plate on the car. (Figure 11)

If the set is insufficiently grounded, it may not

operate or there may be noise.

After the connection, fix the lead by a clamp

or insulation tape for protection.

CAUTION

Figure 11

Figure 10

48 VRX630

English

Installation and Wire

connection manual

∗1:Connect securely to the metal part of the vehicle with a screw, etc.

∗2:Connect to the power supply terminal which can be turned on and off by the ignition switch.

∗3:Connect to the power supply terminal where the power is always supplied regardless of whether the

ignition switch is turned on or off.

∗4:Connect to the remote turn-on lead of amplifiers.

∗5:Use the attached extension lead when necessary.

∗6:Connect the terminal to the lead wire on the lamp side of the parking brake lamp switch. After

connection, apply the parking brake, then check that the TV displays an image.

•If the PKB lead is not connected to the side brake, some units may not operate.

AUDIO 4CH. OUTPUT

terminal

Front right

Front left

Rear right

Rear left

Red

White

Gray

Brack

Gray

Brack

VISUAL/CCD/DVD changer terminal

8. WIRE CONNECTION

VRX630 49

English

Installation and Wire

connection manual

■Connecting the Accessories

•Connection to the external amplifier

The external amplifier can be connected to the AUDIO 4CH. OUTPUT terminal (RCA pin jack) on

the main unit. In other words, it can be connected provided the DSP is connected.

•Connection to the CCD camera for vehicle

The CCD CAMERA for vehicle can be connected to the system expansion terminal on the main

unit. For detailed information, refer to the instruction sheet or manual for the CCD CAMERA.

Notes:

• A power supply box (sold separately) is required for connection of the main unit and the CCD CAMERA.

• While the CCD CAMERA is used, the navigation cannot be turned on.

• The power supply box for camera CCA-147 can not be used. Please use The CCA-188 instead.

•If the specified lead of the cellular phone is connected to the phone mute

lead of the source unit, the audio mute is available when the cellular tele-

phone is used.

For audio mute setting in cellular telephone use, see page 32.

•TVTunner

When theTVTUNER is to be connected, connect the Ce NET connector and RCA PIN (yellow).For

detailed information, refer to the instruction manual of the TV TUNER.

■Connectingthe parking brake lead

Connect the lead to parking brake lamp earth

in the meter panel.

Notes:

• Connecting the parking brake lead to lamp earth

allows you to watch TV/VTR/DVD changer when

the parking brake is engaged.

• When the parking brake lead is not connected,

the monitor will stay off.

Parking brake

Parking brake lamp +lead to battery

Connect these three leads.

-cord

parking

brake signal

lead Parking brake lead

(bright green)

50 VRX630

English

Installation and Wire

connection manual

9. SAMPLE SYSTEMS

(VRX630)

(TTX7501z)

(VCZ625)

(CDC655z/655Tz/1255z/

DCZ625)

CeNET STAND

ALONE

TVTuner

CeNET cable

(included the TV tuner)

RCA video cable

(included the TV tuner)

DVD Changer

CD Changer

CeNET Y-adapter

(CCA-519-601,

sold separately)

Ferrite clamp

(Included the DVD changer)

CeNET Cable

(included the Changer)

Set the [CeNET/STAND ALONE]

switch to the [CeNET] position.

∗To enable the correct input, it is

necessary to configure the VRX630

as described on page 30.

∗When two CD changers or

MD changers are connected,

CCA-519-601 is required.

Main Unit

VIDEO INPUT terminal

VISUAL/CCD/DVD changer terminal

AV Adapter cable

(CCA-389, sold separately)

■Sample System 1

VRX630 51

English

Installation and Wire

connection manual

■Sample System 2

(VRX630)

(VCZ625)

(CDC655z/655Tz/1255z/

DCZ625)

CeNET STAND

ALONE

VTR

(TTX7501z)

TVTuner

CeNET cable

(included the

TV tuner) RCA video cable

(included the TV tuner)

DVD Changer

CD Changer

CeNET Y-adapter

(CCA-519-601,

sold separately)

Ferrite clamp

(Included the DVD changer)

CeNET Cable

(included the Changer)

Front

Speakers

Rear

Speakers

Set the [CeNET/STAND ALONE]

switch to the [CeNET] position.

Amp.

RCA PIN cable

(Sold separately)

∗To enable the correct input, it is

necessary to configure the

VRX630 as described on page

30.

∗When two CD changers or

MD changers are connected,

CCA-519-601 is required.

Amp remote

Main Unit

Rear

Monitor

RCA video cable

(sold separately)

VIDEO INPUT terminal

VISUAL/CCD/DVD changer terminal

AV Adapter cable (CCA-389, sold separately)

∗Images from the DVD changer

cannot be displayed.

52 VRX630

English

Installation and Wire

connection manual

■Sample System 3

(VRX630)

(TTX7501z)

(CDC655z/655Tz/1255z/

DCZ625)

(DPH910)

TVTuner

CeNET cable

(included the TV tuner)

RCA video cable

(included the TV tuner)

CD Changer

CeNET Cable

(included the

Changer)

Front

Speakers

Rear

Speakers

Mini DIN(8P) Cable

(included the

CCD camera)

Amp remote

Main Unit

CCD camera

Sub-

woofer

4-channel

Power Amplifier

2-channel

power amplifier

Digital Sound

Processor

CeNET Cable

(included the DPH910)

RCA PIN cable

(included the DPH910)

Amp remote

RCA PIN cable

(sold separately)

Digital optical fiber cable(sold separately)

VIDEO INPUT terminal

∗To enable the correct input, it is

necessary to configure the VRX630 as

described on page 30.

Andere Handbücher für pro audio vrx 630

Inhaltsverzeichnis

Andere Clarion Autoempfänger Handbücher

Clarion

Clarion CZ501E Reparaturanleitung

Clarion

Clarion CZ102E Bedienungsanleitung

Clarion

Clarion CZ202 Bedienungsanleitung

Clarion

Clarion FB278RBT Bedienungsanleitung

Clarion

Clarion DUB278RMP Bedienungsanleitung

Clarion

Clarion VZ709A Bedienungsanleitung

Clarion

Clarion PU-9079A Bedienungsanleitung

Clarion

Clarion PU-2471A-G Bedienungsanleitung

Clarion

Clarion CZ300 Reparaturanleitung

Clarion

Clarion AXZ610 Bedienungsanleitung

Clarion

Clarion DXZ265 Bedienungsanleitung

Clarion

Clarion DXZ946MP Bedienungsanleitung

Clarion

Clarion DB566USB Bedienungsanleitung

Clarion

Clarion Addzest DXZ825 Bedienungsanleitung

Clarion

Clarion BTS33 Bedienungsanleitung

Clarion

Clarion DXZ385 Bedienungsanleitung

Clarion

Clarion NX302E Bedienungsanleitung

Clarion

Clarion BD169R Bedienungsanleitung

Clarion

Clarion DXZ275MP Bedienungsanleitung

Clarion

Clarion DB185MP Bedienungsanleitung

Clarion

Clarion DXZ746MP Bedienungsanleitung

Clarion

Clarion NX501A Bedienungsanleitung

Clarion

Clarion AB223R Bedienungsanleitung

Clarion

Clarion DXZ646MP Bedienungsanleitung

Beliebte Autoempfänger Handbücher anderer Marken

Motorola

Motorola VWA63 Bedienungsanleitung

Nextar

Nextar D3201 Bedienungsanleitung

Alpine

Alpine CDE-163BT Bedienungsanleitung

Pioneer

Pioneer DEH-P645R Bedienungsanleitung

Axxera

Axxera XDMA7600 Betriebsanleitung

XM OnyX Bedienungsanleitung

Sound Storm

Sound Storm STM93R Bedienungsanleitung

Soundstream

Soundstream VIR-5000 Bedienungsanleitung

Avson

Avson MKT Platform Bedienungsanleitung

Sony

Sony MEX-1HD - Audio Library System Bedienungsanleitung

Pioneer

Pioneer DVH-P500UB Bedienungsanleitung

JVC

JVC KD-AHD69 Bedienungsanleitung

Blaupunkt

Blaupunkt SANTIAGO CR 87 Bedienungsanleitung

Sony

Sony CDX-4160 - Cd Receiver Bedienungsanleitung

XFIRE AUDIO

XFIRE AUDIO BMW42S Bedienungsanleitung

VDO

VDO CD 2253 Bedienungsanleitung

Volvo

Volvo 13 84 580 Bedienungsanleitung

ZENEC

ZENEC ZE-160DVD Bedienungsanleitung

Clarion pro audio vrx 630 Gebrauchsanweisung

Beliebte Autoempfänger Handbücher anderer Marken