Clarke CFP9HND Installations- und Betriebshandbuch

Operating & Maintenance

Instructions 1216

Air Compressor

Models: CFP9HND

Part Number: 2090901

Air Compressor

- 2 -

SPECIFICATIONS

CFP9ND

Part Number 2090901

Engine Type HONDA

Pump Type MK238

Air Receiver size 2.65 litres

Max. output Pressure 100psi

Air Displacement 9cfm

Outlet connectors 1/4” BSP

Dimensions (mm) 520x360x440

Weight (kg) 21

Guarenteed Sound Power Level 96.5dBLWA

NOTE:

Specifications are correct at the time of going to print.

Clarke International reserves the right to change specifications at any time, as it

sees fit, in the interests of safety or improvement in design.

- 3 -

WARNING!

DO NOT ATTEMPT TO ALTER ENGINE SPEED SETTINGS

DOING SO WILL INVALIDATE YOUR GUARANTEE

-4 -

INTRODUCTION

Thank you for purchasing this Clarke Air portable

compressor. The unit is powered by a 5HP Honda engine, a

manual for which, is provided separately. Please refer to

that manual for all matters relating to the engine, ...starting

and stopping procedures, maintenance etc.

Read these safety instructions before using the equipment.

CONTENTS Page

GUARANTEE

This product is guaranteed against faults in manufacture for 12 months

from purchase date. Please keep your receipt as proof of purchase.

This guarantee is invalid if the product has been abused or tampered

with in any way, or not used for the purpose for which it is intended.

The reason for return must be clearly stated.

This guarantee does not affect your statutory rights.

Introduction .................................................................................................................. 4

Guarantee .................................................................................................................... 4

For your Own Safety .................................................................................................... 5

Important General Notes ............................................................................................ 6

General Layout ............................................................................................................ 7

Preparation for Use ...................................................................................................... 8

Starting & Using your Air Compressor ....................................................................... 9

Shutting Down the Compressor ............................................................................... 10

Maintenance .............................................................................................................. 11

Troubleshooting ......................................................................................................... 12

Parts and Service Contacts ...................................................................................... 14

Parts Lists and Diagrams ...................................................................................... 15-17

Declaration of Conformity ........................................................................................ 18

- 5 -

FOR YOUR SAFETY

WARNING

As with all machinery, there are certain hazards involved with their operation and use.

Exercising respect and caution will considerably lessen the risk of personal injury.

However, if normal safety precautions are overlooked, or ignored, personal injury to

the operator, or damage to property may result.

It is in your own interest to read and pay attention to the following rules:

General Precautions

ALWAYS

• ensure that all individuals using the compressor have read and fully understand the

Operating Instructions supplied.

• Stop the engine and ensure the pressure is expelled from the air receiver BEFORE carrying

out any maintenance.

• ensure that there is adequate ventilation when spraying flammable materials e.g.

cellulose paint, and keep clear of any possible source of ignition.

• protect yourself. Think carefully about any potential hazards which may be created by using

the air compressor and use the appropriate protection. e.g.Goggles will protect your eyes

from flying particles. Face masks will protect you against paint spray and/or fumes. Ear defenders

will prevent hearing damage caused by load noise.

• consult paint manufacturers instructions for safety and usage, before spraying

• ensure that the air supply is turned off at the machine outlet and all pressurised air from

the machine and other equipment attached to it, is expelled BEFORE disconnecting air

hoses or other equipment.

• make sure that children and animals are kept well away from the compressor and any

equipment attached to it.

• ensure that any equipment or tool used in conjunction with your compressor, has a

safety working pressure exceeding that of the machine.

NEVER

• direct a jet of air at people or animals, and NEVER discharge compressed air against

the skin. COMPRESSED AIR CAN BE DANGEROUS!

• leave pressure in the receiver overnight, or when transporting.

• adjust, or tamper with the safety valves. The maximum pressure is factory set, and clearly

marked on the machine.

• operate in wet or damp conditions. Keep the machine dry at all times. Similarly, a clean

atmosphere will ensure efficient operation. Do not use in dusty or otherwise dirty locations.

• touch the machine until it has cooled down...some of the metal parts can become

quite hot during operation.

• operate your compressor with any guards removed.

- 6 -



Fire Prevention

ALWAYS

•switch the engine OFF when refuelling.

•refuel away from any source of heat.

•refuel in a well ventilated area.

NEVER

•overfill the tank, fill to the level specified.

•smoke whilst refuelling and avoid smoking or using a naked flame near the compressor.

•start the engine if there is spilled fuel. Any spillage must be wiped clean and the

compressor allowed to dry before attempting to start the engine.

IMPORTANT General Notes

• NEVER allow anyone, not fully familiar with compressors, to use this equipment.

• DO NOT alter the engine settings....these settings are set at the factory. Should they

need recalibration - consult your Clarke dealer

Exhaust Gas Precautions

WARNING:

Exhaust fumes can be fatal

ALWAYS

• ensure there is adequate ventilation when using the compressor.

• position the compressor so that the exhaust is pointed away from people or animals .

NEVER

• Do not use the compressor indoors or in an enclosed area. (i.e. in a warehouse, tunnel,

well, hold etc.)

Fig.1

- 7 -

CFP9ND

GENERAL LAYOUT

- 8 -

PREPARATION FOR USE



The engine and compressor are supplied without oil inside, a small bottle is

provided in the box and must be added before use (approx 0.6l to the

engine and 0.4l to the pump).

A.Environmental

• Ensure the compressor is sited on a firm level surface.

• Ensure the environment is dry and dust free.

• Ensure there is adequate ventilation for:

a) Air intake to compressor pump

b) Cooling for compressor pump

c) Engine exhaust gases.

B. Engine

• Perform a visual check of components and check oil and fuel levels .

Refer to engine service manual.

C. Pump

• Check

oil level on the Dipstick - to level marked.

D. Fueling

Fill with unleaded petrol, according to the instructions within the engine manual.

• Ensure the fuel tap is set to the required position.

• Ensure The fuel hose and connectors are intact, in perfectly servicable

condition and there is no leakage.

Note : Always use a funnel to fill the fuel tank so as to avoid accidental spillage of

fuel. If fuel is spilled it must be removed from the unit and surrounding area, before

attempting to start the engine.

E. Receiver

• Drain off any condensate, by opening the drain cock (see Fig. 1).

Remember to close the cock when completed.

NOTE: This should be carried out DAILY when the compressor is in constant use.

F. Air Hose & Air Tool

• Attach the air hose to the outlet using an appropriate connector.

• Attach the air tool/spray gun to the air hose...If using snap couplings, use

a whip end, available from your Clarke dealer.

STARTING AND USING THE COMPRESSOR

First time startup

NOTE: For first time operation, do not connect the air hose or any tools and proceed

as follows:

1. Start the engine, according to the instructions contained in the engine service

manual, and allow to run for 10 minutes.

2. After a ten minute period, stop the

engine and attach an air hose to

the air outlet and the tool.

3. Screw the pressure regulator fully

anticlockwise, then restart the

engine and allow presure to build

up in the receiver.

Screw the pressure regulator

clockwise until the pressure,

registered on the Pressure Gauge,

is 100psi.

At this point, check the system for air

leaks. If any are apparent, stop the

engine and operate the tool until the

air pressure is at zero, or open the

drain cocks before rectifying.

NOTE: Air will blow off at the bleed hole when the pressure reaches 100psi,

which is the MAX. operating pressure.

4. With the engine running, turn the pressure regulator so that your desired

pressure is registered on the gauge, and proceed to use the air tool in

accordance with the manufacturers instructions.

When starting subsequently, start the machine as follows:

1. At the begining of the day, open the drain cocks (see Fig.1) and allow any

condensate to drain completely, then close the cocks.

2. Connect the air hose to the air outlet and tool, and set the pressure regulator

to zero pressure (turned fully anticlockwise).

3. Start the engine in accordance with the instructions contained in the engine

service manual, and allow pressure to build up.

4. When the pressure in the receiver has built up and air blows off at the bleed

hole, turn the outlet pressure regulator clockwise so that the desired pressure is

registered on the pressure gauge and proceed to use the air tool/spray gun.

5. Check for air leaks at the tool and connectors...as above, before proceeding.

Fig.2

- 9 -

STOPPING THE COMPRESSOR

At the end of the day, stop the engine in accordance with the instructions in the

engine manual, then open the drain cock.

1. Turn the regulator fully anticlockwise.

2. Operate the air tool trigger or operating lever etc., to ensure there is no pressure

in the air line, then disconnect airline and tool.

DO NOT under any circumstances attempt to remove the air tool or disconnect

the air hose until you are satisfied that the pressure has been relieved.

3. Finally, close the drain cock.

Take care not to touch the engine or pump as they remain hot for some time after

use.

- 10 -

REPLACEMENT OILS

Replacement oils are available from your Clarke dealer as follows:

1 litre of Compressor pump oil - Part No. 3050796

1 litre of Engine oil - Part No. 3050852

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Clarke Luftkompressor Handbücher

Clarke

Clarke Air XP15 Bedienungsanleitung

Clarke

Clarke SHHHAIR MAX 24/150 Bedienungsanleitung

Clarke

Clarke SHHHAIR 30/9 Bedienungsanleitung

Clarke

Clarke Raider 55 Bedienungsanleitung

Clarke

Clarke 2242117 Bedienungsanleitung

Clarke

Clarke SHHH2 Installations- und Betriebshandbuch

Clarke

Clarke PANTHER 10/240 Bedienungsanleitung

Clarke

Clarke Ranger 7/240 Bedienungsanleitung

Clarke

Clarke 2242119 Bedienungsanleitung

Clarke

Clarke RANGER 45 Bedienungsanleitung

Clarke

Clarke SE Ranges Installations- und Betriebshandbuch

Clarke

Clarke AIRMASTER 18/150 Bedienungsanleitung

Clarke

Clarke SHHHAIR 100/50 Bedienungsanleitung

Clarke

Clarke CHT747 Bedienungsanleitung

Clarke

Clarke CHAMP 262 Installations- und Betriebshandbuch

Clarke

Clarke SHHHAIR MAX 50/350 Bedienungsanleitung

Clarke

Clarke XE10/100 Bedienungsanleitung

Clarke

Clarke SHHHAIR 30/9 Bedienungsanleitung

Clarke

Clarke SHHHAIR 30 Bedienungsanleitung

Clarke

Clarke CSC1000 Handbuch

Clarke

Clarke BOXER 100 Bedienungsanleitung

Clarke

Clarke Ranger 25A Betriebsanleitung

Clarke

Clarke SHHHAIR 100/24 Bedienungsanleitung

Clarke

Clarke ZX 500 Fehlerbehebungshandbuch

Beliebte Luftkompressor Handbücher anderer Marken

Sparmax

Sparmax DC-25XR Bedienungsanleitung

KAESER

KAESER M122 Bedienungsanleitung

Briggs & Stratton

Briggs & Stratton Air Compressor Bedienungsanleitung

Fini

Fini F3GST2TK Bedienungsanleitung

Industrial Air

Industrial Air CP1580325 Programmierhandbuch

Campbell Hausfeld

Campbell Hausfeld RP3300 Kurzanleitung

Ingersoll-Rand

Ingersoll-Rand UP6 20 HP Bedienungsanleitung

Hitachi

Hitachi EC99S Bedienerhandbuch

Parkside

Parkside PKO 270 A1 Bedienungsanleitung

Clas Ohlson

Clas Ohlson QIE-ZTH-15 Bedienungsanleitung

Ferm

Ferm CRM1046 Bedienungsanleitung

BE AC153 Bedienungsanleitung

RIDGID

RIDGID OF25150A Bedienungsanleitung

Johnson Controls

Johnson Controls QUANTUM LX Handbuch

Sears

Sears Craftsman 919.167463 Bedienungsanleitung

Ring Automotive

Ring Automotive RAC700 Bedienungsanleitung

Craftsman

Craftsman 919.152144 Bedienungsanleitung

Alkin

Alkin W3 Series Bedienungsanleitung