Clarke CLC1 Bedienungsanleitung

OPERATING INSTRUCTIONS

GC0611

LAMINATE FLOOR CUTTER

Model No: CLC1

PART NO: 3400670

INTRODUCTION

Thank you for purchasing this CLARKE Laminate Floor Cutter. This CLARKE

product has been designed to give long and trouble free service. If however,

having followed the instructions in this booklet carefully, you encounter

problems, take the unit to your local CLARKE dealer.

The CLC1 can cut any laminated MDF flooring up to 8” (203mm) wide, 7/16”

(11mm) thick but is not designed for other materials. The fence can be

positioned at 150 or 203mm from the blade.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase. This guarantee is invalid if the product is found

to have been abused, tampered with, or not used for it’s intended purpose.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission. This guarantee does not effect

your statutory rights.

GENERAL SAFETY PRECAUTIONS

1. Always thoroughly familiarise yourself with this product & its operation, and

always read and understand the instructions and warnings in this manual

before using the equipment.

2. Always wear safety glasses when operating this tool.

3. Keep cutting blade in the fully closed position when not in use.

4. Keep fingers and hands away from blade cutting area.

5. Periodically check that all hardware remains tight.

6. Always keep out of reach of children.

ASSEMBLY

Upon receipt of the product, unpack the components and check for

deficiencies. The CLC1 laminate Cutter should include the following:

• Main Frame Assembly • Blade • Work Support

• Operating Handle c/w fixings • Guide Fence c/w fixings

• Self adhesive pads (non-slip)

1. Assemble handle (10) to the cutting blade (3) with the three screws (11),

with washers (9) & nuts (8) as shown in the component parts diagram.

2. Attach the blade assembly (1) to the cutter base (12) using the two nylon

spacers (2 & 4) and axle (7) as shown in the diagram, securing with the

nuts & washers (5 & 6).

3. Attach the guide fence (14) to the frame (12) at one of the two available

positions using the screws (13).

COMPONENT PARTS

1 Blade Assembly

2 Right Nylon Spacer

3 Cutting Blade

4 Left Nylon Spacer

5 M10 Locknut

6 10mm Washer

7 Axle

8 M6 Nut

9 6mm Washer

10 Handle

11 Screw M6 x 17mm

12 Cutter Base

13 Screw M6 x 13mm

14 Guide Fence

15 Self-Adhesive Pad

16 Work Support

OPERATING INSTRUCTIONS

1. Place cutter on a level floor.

2. Mark the work piece to be cut and insert it against the guide fence.

• Use the work support (16) to support the laminate while cutting.

• Always cut the laminate with the finished side up.

• Place the grooved or indented side of the laminate against the fence.

(The "tongue" side should be closest to the blade.)

3. Begin the cut by holding the laminate firmly with one hand and cutting

into the laminate. Once the blade has penetrated the laminate, proceed

using both hands with a smooth powerful downward motion to complete

your cut.

4. Remember the cut side should always be placed along the wall to be

covered up by skirting or finish moulding.

MAINTENANCE

1. Keep the cutter clean and store in a dry place when not in use.

2. Keep edges of blade sharp by using a sharpening stone.

3. Periodically check that all nuts and bolts are tight.

Inhaltsverzeichnis

Andere Clarke Cutter Handbücher

Clarke

Clarke ETC8 Bedienungsanleitung

Clarke

Clarke CHT532 Bedienungsanleitung

Clarke

Clarke WE6493A Bedienungsanleitung

Clarke

Clarke CHT518 Bedienungsanleitung

Clarke

Clarke 20CI Bedienungsanleitung

Clarke

Clarke CMB710 Bedienungsanleitung

Clarke

Clarke TCM430 Bedienungsanleitung

Clarke

Clarke ETC180 Kurzanleitung

Clarke

Clarke ETC7 Installations- und Betriebshandbuch

Clarke

Clarke ETC6 Installations- und Betriebshandbuch

Clarke

Clarke ETC8 Bedienungsanleitung

Clarke

Clarke ETC400 Fehlerbehebungshandbuch

Clarke

Clarke X-Pro CAT203 Installations- und Betriebshandbuch

Clarke

Clarke Strong-Arm CS10HC Installations- und Betriebshandbuch

Clarke

Clarke 30SI Installations- und Betriebshandbuch

Clarke

Clarke 1801518 Bedienungsanleitung

Clarke

Clarke CAT127 Installations- und Betriebshandbuch

Clarke

Clarke TCM420 Bedienungsanleitung

Clarke

Clarke ETC180 Handbuch

Beliebte Cutter Handbücher anderer Marken

Milwaukee

Milwaukee HEAVY DUTY M12 FCOT Bedienungsanleitung

SignWarehouse.com

SignWarehouse.com Bobcat BA-60 Bedienungsanleitung

Makita

Makita 4112HS Bedienungsanleitung

GEISMAR STUMEC

GEISMAR STUMEC MTZ 350S Bedienungsanleitung

Hitachi

Hitachi CM 4SB2 Fehlerbehebungshandbuch

Dexter Laundry

Dexter Laundry 800ETC1-20030.1 Bedienungsanleitung

GCC Technologies

GCC Technologies AFJ-24S Bedienungsanleitung

DeWalt

DeWalt XR LI-ION DCS350N Bedienungsanleitung

Baudat

Baudat ES1 Bedienungsanleitung

Mafell

Mafell ZAF 200 Leitfaden

Makita

Makita 4100NH Bedienungsanleitung

Formax

Formax FD 574 Bedienungsanleitung

EINHELL

EINHELL TE-MA 1500 Bedienungsanleitung

Husqvarna

Husqvarna Cut-n-Break K 760 Bedienungsanleitung

CLEAN ROOM DEVICES

CLEAN ROOM DEVICES CRD130SS Bedienungsanleitung

TRI tool

TRI tool 301A Bedienungsanleitung

Roller

Roller King 1 1/4 Bedienungsanleitung

RODCRAFT

RODCRAFT RC7170 Bedienungsanleitung