Clarke DEVIL 2000PTC Bedienungsanleitung

OPERATION & MAINTENANCE

INSTRUCTIONS

ORIGINAL INSTRUCTIONS GC0717

2KW ELECTRIC FAN HEATER

MODEL NO: DEVIL 2000PTC

PART NO: 6925590

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE product.

Read this manual carefully, in doing so you guarantee the safety of yourself

and that of others around you, and you can look forward to your purchase

giving you long and satisfactory service.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt as proof of

purchase.

This guarantee is invalid if the product is found to have been abused,

tampered with, or not used for the purpose for which it was intended.

Faulty goods must be returned to their place of purchase, no product can be

returned to us without prior permission.

This guarantee does not effect your statutory rights.

SPECIFICATIONS

Operating Voltage and Frequency: (V / Hz) 230 V / 50Hz

Operating Temperature: (Min/Max) (°C): -15 to 25°C

Heat Output: (kW): 2 kW

Air Output: (m3/h) 197m3/h

Safety Device: Thermal cut-out

Duty Cycle Classification: Continuous duty

Electrical Insulation Class I

Product: Depth x Width x Height 211 x 165 x 215 mm

Product Weight 1.74 kg

Sound Pressure Level 43 dB

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SAFETY SYMBOLS

These safety symbols appear on the heater.

SAFETY RULES

Make sure that you read, understand and comply with the following.

ELECTRICAL SAFETY

• Regularly inspect the power cable / plugs for damage/looseness. Do

not use the heater it the power cable is damaged.

• Minimise the risk of electric shock by installing a RCCB (Residual Current

Circuit Breaker) and a suitable isolator into the main distribution board.

• Make sure that the voltage on the rating label is the same as the voltage

of the power supply. If in doubt, consult a qualified electrician.

• Do not abuse the electrical cable. Do not use the cable for pulling or

unplugging the heater.

• Keep the cable away from sources of heat, oil, sharp edges or moving

parts. Damaged or tangled cables increase the risk of electric shock.

• Do not use extension cables with this heater.

Hot Surface,

Do Not Touch

Do Not Cover

WEEE Directive for the

disposal of waste

elecrical & electronic

equipment

WARNING: THIS HEATER MUST BE EARTHED

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

MAINTENANCE.

• Check that the heater is in good working order. Take immediate action

to have it repaired or any damaged parts replaced.

• DO NOT attempt to repair a damaged heater yourself. Always contact

the Clarke service department.

• Do not allow the heating elements to become covered with dust, which

could become a fire hazard. If used in a dusty workplace it should be

cleaned as described under Cleaning and Maintenance.

• The Clarke service department will use recommended parts only.

Unapproved parts may be dangerous and will invalidate the warranty.

POSITIONING

• This heater is designed for indoor use only.

• DO NOT place the heater close to a bath, wash basin, shower, swimming

pool or any other water-filled area or wet surface. DO NOT place the

heater against any surface such as a wall, door or furniture etc.

• DO NOT place the heater immediately below any electrical outlet.

• NEVER place the heater near combustible materials such as curtains,

furniture etc. Allow 2 metres clearance all round this heater.

• DO NOT place the heater on a raised surface or anywhere it could

topple over

• Take care to ensure that the grille cannot be blocked by curtains or

other fabrics.

• Do not operate fan heater in explosive atmospheres such as in the

presence of flammable liquids, gasses or dust such as in a paint spray

booth, or any explosive environment. Electric motors create sparks

which may ignite dust or fumes.

WARNING: DISCONNECT THE HEATER FROM THE POWER SUPPLY BEFORE

SERVICING OR PERFORMING ANY MAINTENANCE. THIS MUST ONLY BE

CARRIED OUT BY THE CLARKE SERVICE DEPARTMENT.

WARNING: DO NOT USE THE HEATER NEAR FLAMMABLE MATERIAL,

LIQUIDS, SOLIDS, GASSES OR COMPRESSED GAS CYLINDERS ETC.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

COMMON SENSE

• DO NOT operate the heater when you are tired or under the influence of

alcohol, drugs or intoxicating medication.

• DO NOT stand on the heater.

• DO NOT use the heater with wet hands or when there is water on the

power cable.

• Turn the heater off when not in use and keep it in a safe, dry, childproof

location.

• The heater is designed to heat enclosed areas such as workshops and

other industrial areas. Do not use the heater for any other function. It is

not suitable for drying clothes or laundry.

• Young children must be kept away unless continuously supervised.

OPERATION

• The heater must only be used by people who have read these

instructions and have been trained in its use.

• DO NOT obstruct the air inlet and outlet sections of the heater.

• DO NOT cover the heater.

• DO NOT touch the heater casing or grille when first switched off, as these

will be very hot and will take time to cool.

• DO NOT get the heater wet or use in areas of high condensation.

• DO NOT allow the power lead to touch hot surfaces.

• DO NOT connect other appliances to the same mains socket as the

heater.

• Only use the heater in a level position.

• Do not use this heater with a programmable timer used to switch it on

automatically.

SERVICE & REPAIRS

• Have your appliance repaired by a qualified person using identical

replacement parts. This will ensure that the safety of the appliance is

maintained.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ELECTRICAL CONNECTIONS

Connect the mains lead to a standard, 230 Volt (50Hz) electrical supply

through an approved 13 amp BS 1363 plug, or a suitably fused isolator switch.

If the plug has to be changed because it is not suitable for your socket, or

because of damage, it must be removed and a replacement fitted, following

the wiring instructions shown below. The old plug must be discarded safely, as

insertion into a power socket could cause an electrical hazard.

If the colours of the wires in the power cable do not agree with the markings

on the plug.

• The BLUE wire must be

connected to the

terminal which is

marked N or coloured

black.

• The BROWN wire must

be connected to the

terminal which is

marked L or coloured

red.

• The YELLOW AND

GREEN wire must be

connected to the terminal which is marked E or or coloured green.

We strongly recommend that this machine is connected to the mains supply

through a Residual Current Device (RCD)

If you are not sure, consult a qualified electrician. DO NOT try to do any

repairs.

WARNING: READ THESE ELECTRICAL SAFETY INSTRUCTIONS

THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE MAINS

SUPPLY.

WARNING: THE WIRES IN THE POWER CABLE OF THIS PRODUCT ARE

COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:

BLUE = NEUTRAL BROWN = LIVE YELLOW AND GREEN = EARTH

Plug must be BS1363/A approved.

Always fit

Ensure that the outer sheath of

Neutral

(Blue)

Live

(Brown)

Earth

(Green and

a 13 Amp

the cable is firmly held by the clamp

fuse.

Yellow)

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

OPERATION

1. Place the heater in a level position on a flat surface and at a safe distance

from flammable materials. Keep 2m clearance all round.

2. Connect the heater to a suitable

power supply.

3. Set the thermostat control to the

maximum setting (fully clockwise).

4. Set the mode selector to one of

the following settings:

• The heater will take up to three minutes to reach optimum temperature.

5. Once the room reaches the required temperature, turn the thermostat

control slowly counter-clockwise until the thermostat clicks, leave the

control in this position.

WARNING: DO NOT USE THIS HEATER IN SMALL ROOMS WHEN THEY ARE

OCCUPIED BY PERSONS NOT CAPABLE OF LEAVING THE ROOM ON THEIR

OWN, UNLESS CONSTANT SUPERVISION IS PROVIDED.

CAUTION: PARTS OF THIS HEATER CAN BECOME VERY HOT AND CAUSE

BURNS. PARTICULAR ATTENTION HAS TO BE GIVEN WHERE CHILDREN

AND VULNERABLE PEOPLE ARE PRESENT.

Off

Fan Only

Fan + Heat Setting 1

Fan + Heat Setting 2

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

• The heater will continue to operate until the power switch is turned to

the OFF position.

6. For fan only operation, turn the power switch to the fan only setting and set

the thermostat to its minimum setting.

7. When not in use, disconnect the heater from the mains supply. Store it in a

safe, dry, childproof location.

ADJUSTING THE ANGLE

1. Loosen both handwheels.

2. Adjust to the the required angle.

3. Retighten the handwheels.

SAFETY SYSTEMS

THERMOSTATIC PROTECTION

The Devil 2000PTC has a thermal cut out to prevent it from overheating.

If the temperature of the front grille gets too high the thermal cutout will turn

off the heating elements. When the fan has cooled the unit sufficiently, normal

operation will resume.

MAINTENANCE

• Clean the heater with a soft damp cloth, Do not use solvents or

abrasives.

• Make sure that the heater grille is not blocked.

• No other maintenance is required, should you discover any problem

with the heater, return it to the Clarke service department for repair.

WARNING: ALWAYS DISCONNECT FROM THE POWER SUPPLY AND ALLOW

THE HEATER IT TO COOL DOWN BEFORE PERFORMING ANY

MAINTENANCE TASKS.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

TROUBLE SHOOTING

ENVIRONMENTAL RECYCLING POLICY

Through purchase of this product, the customer is taking on the

obligation to deal with the WEEE in accordance with the WEEE

regulations in relation to the treatment, recycling & recovery and

environmentally sound disposal of the WEEE.

In effect, this means that this product must not be discarded with general

household waste. It must be discarded according to the laws governing

Waste Electrical and Electronic Equipment (WEEE) at a recognised disposal

facility.

Problem Possible Cause Remedy

Heater does

not

operate,

although

plugged in

with the

switch and

thermostat

switched on.

Plug is loose/bad

connection.

Pull the plug out & check the connection of

the plug and socket.

Fuse blown or

circuit breaker

trips.

Replace if necessary and investigate

cause. If fuse blows repeatedly, consult

your Clarke dealer.

No power at

socket outlet

Insert the plug in a funtioning socket

Heating

element

glowing hot.

Input voltage too

high.

Use a power supply in accordance with the

rating on the label.

Air inlet grille is

blocked

Ensure the heater is kept away from any

objects which could cover the air inlet or

be drawn into it.

The unit has

failed to heat

up so only the

air fan has

operated.

Control switch not

set at a "HEATING"

level.

Turn switch to a heating level.

Thermostat has

tripped.

Turn the thermostat and listen. If there is no

CLICK and the thermostat is not damaged,

the heater will automatically switch ON

when it has cooled down.

Abnormal

noise.

Heater is not level. Stand heater on a level surface

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

PARTS LIST & DIAGRAM

Part number is ZNBDEV2000PTC + (item number) eg the power cable is

ZNBDEV2000PTC15.

NO DESCRIPTION NO DESCRIPTION

1 Front Grille 12 Control Box

2 Air Outlet 13 Outer Casing

3 PTC Heating Element 14 Cable Fastener

4 Air Flue 15 Back Grill

5 Motor 16 Power Cable

6Fan 17Screw

7 Ajustable Thermostat 18 Rubber Gasket

8 Rotary Switch 19 Steel Pipe

9 Switch Knob 20 Feet

10 Indicator Lamp Cover 21 Self Setting Thermostat

11 Thermostatic Knob 22 Metal Thermal Protection

Inhaltsverzeichnis

Andere Clarke Heizung Handbücher

Clarke

Clarke IQ2000 Bedienungsanleitung

Clarke

Clarke DEVIL IRD40B Bedienungsanleitung

Clarke

Clarke OFR 9 Bedienungsanleitung

Clarke

Clarke 6933990 Bedienungsanleitung

Clarke

Clarke DEVIL 371PC Installations- und Betriebshandbuch

Clarke

Clarke DEVIL 340 Bedienungsanleitung

Clarke

Clarke DEVIL 350C Installations- und Betriebshandbuch

Clarke

Clarke DEVIL 2800PTC Bedienungsanleitung

Clarke

Clarke IQ2000S Stücklistenhandbuch

Clarke

Clarke CONTRACTOR DEVIL 351C Installations- und Betriebshandbuch

Clarke

Clarke DEVIL 7030 Bedienungsanleitung

Clarke

Clarke XR80 Bedienungsanleitung

Clarke

Clarke Devil 6003 Bedienungsanleitung

Clarke

Clarke DEVIL155 Handbuch

Clarke

Clarke DEVIL 370PD Installations- und Betriebshandbuch

Clarke

Clarke CFI 1800 Bedienungsanleitung

Clarke

Clarke DEVIL 6025 Bedienungsanleitung

Clarke

Clarke OFR 9/90 Bedienungsanleitung

Clarke

Clarke DEVIL 370SPC Installations- und Betriebshandbuch

Clarke

Clarke DEVIL 5000PTC Bedienungsanleitung

Clarke

Clarke XR60B Bedienungsanleitung

Clarke

Clarke GH1 Bedienungsanleitung

Clarke

Clarke IRD20 Bedienungsanleitung

Clarke

Clarke XR75 Installations- und Betriebshandbuch

Beliebte Heizung Handbücher anderer Marken

oventrop

oventrop Regucor Series Bedienungsanleitung

Blaze King

Blaze King CLARITY CL2118.IPI.1 Bedienungsanleitung

ELMEKO

ELMEKO ML 150 Bedienungsanleitung

BN Thermic

BN Thermic 830T Bedienungsanleitung

KING

KING K Series Leitfaden

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Kurzanleitung

Well Straler

Well Straler RC-16B Bedienungsanleitung

EUROM

EUROM 333299 Bedienungsanleitung

Heylo

Heylo K 170 Bedienungsanleitung

Eterna

Eterna TR70W Bedienungsanleitung

IRSAP

IRSAP The Radiator Company Ovali Bedienungsanleitung

Empire Heating Systems

Empire Heating Systems WCC65 Bedienungsanleitung

Wetekom

Wetekom 92 86 43 Bedienungsanleitung

Desa

Desa SPC170-F Bedienungsanleitung

Watlow

Watlow Watrod Electric Tubular Heaters Bedienungsanleitung

Haverland

Haverland ECO-DRY GPS Series Stücklistenhandbuch

Stelpro

Stelpro ASILVC2060 Series Bedienungsanleitung

iLO

iLO IHP2424 Betriebsanleitung