Clarke CBSS1 Bedienungsanleitung

MOUNTING & USER

INSTRUCTIONS

GC1014

BICYCLE LIFT

MODEL NO: CBSS1

PART NO: 4510060

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE Bicycle Lift.

Before attempting to use this product, please read this manual thoroughly and

follow the instructions carefully. In doing so you will ensure the safety of yourself

and that of others around you, and you can look forward to your purchase

giving you long and satisfactory service.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not effect your statutory rights.

SPECIFICATIONS

MODEL CBSS1

Rope Length 16 m

Hook Length 60 mm

Component Weight 1.6 kg

Safe Working Load 45 kg (100 lbs)

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SAFETY PRECAUTIONS

1. Always read the instructions before installing.

2. Clarke International is not responsible for any damage resulting from

improper installation or overloading.

3. Suitable for indoor, non-industrial use only.

4. Before using the lift, make sure that it has been installed correctly and is

operating properly.

5. This product is designed to be used by an able bodied, competent adult

who has read and understood these instructions.

6. Never use undue effort to force the lift to operate. If resistance is felt,

investigate the cause.

7. Ensure that the ceiling joist is in good condition and suitably strong to

support the mounting subject to max load.

8. Keep children, animals and bystanders away from the lifting area.

9. Before use, always inspect the bicycle lift and its mountings to ensure they

are in good condition. If any damaged or broken parts are found, the

equipment should be removed from service and the parts renewed or

repaired before further use.

10. This bicycle lift system is mainly intended for lifting bicycles but can safely

be used for storing other items such as ladders.

11. Ensure that the weight of the load to be lifted is within the safe rated load

of this product.

12. Never lift the load at a sideways angle.

IMPORTANT: Safe Working Load 45 kg.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INVENTORY

Unpack your bicycle lift and make sure that the following items are present.

Should there be any damage caused during transit contact your Clarke

dealer immediately.

1. Lift Assembly (front)

2. Lift Assembly (rear)

3. 2 x Hook/Pulley units

4. Rope

5. Rope Wall Cleat

6. 2” Woodscrews and wall-plugs

TOOLS REQUIRED

• Phillips (cross-head) screwdriver

• Tape Measure

• Stud Locator for ceilings/dry walling

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INSTALLATION

1. Measure the distance between

the bicycle handlebars and the

back of the seat.

2. Locate a suitable ceiling joist and

transfer the seat/handlebar

measurement along the joist so

that the lifting attachment points

line up as Fig 1.

3. If it is necessary to mount the

bicycle lift at 90oto the ceiling

joists, simply mount the lift

assemblies to a plywood/timber

board and then attach the board

to the joists as shown in Fig 2.

4. Tie a stop or double knot in the

end of the rope. Feed the rope

through the square hole in the

rear lift assembly that does not

have the locking mechanism, so

that the knotted end sits between

the ceiling and the lift assembly.

5. Using the wood screws provided,

mount each of the lift assemblies

to the ceiling joist(s), as shown in

Fig 3, ensuring that the hooks line

up with the handlebar/seat

measurement.

• Pre-drilling pilot holes will make

this easier.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

6. Thread the rope through the pulleys as shown in Fig 4. Be sure to thread the

rope down through both parts of the locking mechanism (finally emerging

through the round hole) as shown in Fig 5a.

7. Use 2 wood-screws to mount the

rope cleat to the wall as shown in

Fig 5b.

8. When the bicycle is raised to the

ceiling, the excess rope should be

stored by coiling up and hanging

from the cleat.

USING THE BICYCLE LIFT

LIFTING THE BICYCLE

1. Attach the hooks to the bicycle

handlebar and seat as shown.

taking care that the lifting rope is

not twisted. The bicycle can now

be raised to the ceiling by pulling

the rope. If pulled at an angle in

line with the bicycle, as shown in

fig 6, the rope will lock in place to

take the weight of the bicycle.

• The rope should remain locked

while it is under tension but

check that it is held before letting go.

2. Tie the rope to the wall cleat and coil the excess rope to hang from it.

Never cut the rope tail off.

3. Always look for any defects occurring during operation and stop using the

lift if any are seen.

4. Always take care to pull the rope in line with the pulleys to ensure the rope

passes smoothly through the mechanism.

5. Lift the load sufficient to take up the strain and check stability before

commencing the full lift.

6. Ensure that no obstruction prevents a clean lift and that the hooks are

securely attached before lifting.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

LOWERING THE BICYCLE

1. Pull the rope towards the rear pulley in the direction shown as “unlock” to

release the locking mechanism as shown in Fig 6, while maintaining tension

on the rope.

• The tension will keep the locking mechanism open and allow the

bicycle to lower.

2. Slowly let the rope out as the bicycle lowers. Once the bicycle is lowered,

remove it from the hooks and tie the rope back to the cleat.

3. When lowering a load, be aware that when the rope is released, the load

will not stop unless the locking device is engaged.

PERIODIC MAINTENANCE

Before use, it is recommended to carry out the following checks. When in

constant use, the system should be inspected more frequently.

1. Check the security and condition of the mounting point.

2. Check the condition of the hooks and the security of all screws.

NOTE: the nuts and bolts must still have enough freedom to move.

3. Check the condition of the rope and that it is not chaffed or fraying.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Clarke Hebesystem Handbücher

Clarke

Clarke STRONG-ARM HTL300 Bedienungsanleitung

Clarke

Clarke Strong-Arm CPL30S Installations- und Betriebshandbuch

Clarke

Clarke Strong-Arm CML4 Bedienungsanleitung

Clarke

Clarke CML5 Handbuch

Clarke

Clarke CML6 Bedienungsanleitung

Clarke

Clarke STRONG-ARM CFSR500P Bedienungsanleitung

Clarke

Clarke Strong Arm CML2 Installations- und Betriebshandbuch

Clarke

Clarke Strong-Arm CGLK1 Bedienungsanleitung

Clarke

Clarke STRONG-ARM CML3 Leitfaden

Clarke

Clarke Strong-Arm CPL30T Installations- und Betriebshandbuch

Clarke

Clarke CFC100 Installations- und Betriebshandbuch

Clarke

Clarke Strong Arm HTL 300 Installations- und Betriebshandbuch

Clarke

Clarke STRONG-ARM CCL2250 Bedienungsanleitung

Clarke

Clarke STRONG-ARM CB10 Installations- und Betriebshandbuch

Clarke

Clarke CEC500DS Bedienungsanleitung

Beliebte Hebesystem Handbücher anderer Marken

morse

morse 82H-124 Bedienungsanleitung

Braun

Braun NL955 Series Bedienungsanleitung

haacon

haacon 1889.10 Bedienungsanleitung

Protekt

Protekt AT 252 Bedienungsanleitung

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Bedienungsanleitung

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Bedienungsanleitung

Genie

Genie Z-60/34 Bedienungsanleitung

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Bedienungsanleitung

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Bedienungsanleitung

Custom Equipment

Custom Equipment Hy-Brid 3 Series Programmierhandbuch

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Programmierhandbuch

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Programmierhandbuch

BERG

BERG BeNomic EasyLeaf Bedienungsanleitung

Powermate

Powermate LiftGate LG-3 Bedienungsanleitung

Snorkel

Snorkel TM12 Series Bedienungsanleitung

Terberg

Terberg OMNIDEKA Bedienungsanleitung

Harmar Mobility

Harmar Mobility AL625 Betriebsanleitung

Rotary

Rotary SPO16 Bedienungsanleitung