Clarke CDM80 Bedienungsanleitung

CDM80 PEN PROBE DIGITAL MULTIMETER

OPERATING MANUAL

Model CDM80 / Part No:4500085

WARRANTY

Thank you for purchasing this CLARKE Digital Multimeter. Please read this manual thoroughly and

follow the instructions carefully. Before attempting to use the multimeter, thoroughly familiarise

yourself with this device & its operation. In doing so you will ensure the safety of yourself and

others around you, & can look forward to the multimeter giving you long and satisfactory service.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12 months from the date of

purchase. Please keep your receipt which will be required as proof of purchase. This guarantee is

invalid if the product is found to have been abused or tampered with in any way, or not used for the

purpose for which it was intended. Faulty goods should be returned to their place of purchase, no

product can be returned to us without prior permission. This guarantee does not effect your

statutory rights.

READ ALL INSTRUCTIONS BEFORE OPERATING

SAVE THESE INSTRUCTIONS

Thank you for purchasing your Clarke CDM80 Pen Probe Digital Multimeter. Before attempting to

operate your new Multimeter please read these instructions thoroughly. You will need these

instructions for the safety warnings, precautions, assembly, operation, maintenance procedures,

parts list and diagrams. Keep your invoice with these instructions. Write the invoice number on the

inside of rear cover. Keep the instructions and invoice in a safe, dry place for future reference.

The warnings, cautions and instructions discussed in this instruction manual cannot cover all

possible conditions or situations that could occur. It must be understood by the operator that

common sense and caution are factors which cannot be built into this product, but must be

supplied by the operator.

TABLE OF CONTENTS

Warranty ............................................. 2

Safety Rules ....................................... 7

During Use.......................................... 8

Symbols ..............................................10

Preventive Maintenance .................... 12

Description ........................................ 13

Overview ............................................ 14

Specifications .................................... 18

Operation ........................................... 27

DataHold ................................. 27

Max Value Measuring & Hold 27

Switching Functions..................28

Switching Auto/Manual Range.. 28

Auto Power Off .......................29

Taking Measurements .......................30

Measuring DC Voltage ............30

Measuring AC Voltage.............34

Measuring Resistance.............37

Diode Testing .........................40

Continuity Testing ...................43

Measuring DC Current ...........44

Measuring AC Current.............46

Logic Test ...............................48

Maintenance ......................................50

Battery Replacement ..............50

Test Lead Replacement ..........52

Accessories .......................................53

WARNING:- BE EXTREMELY CAREFUL IN THE USE OF THIS METER. Improper use

of this device can result in electric shock to the user or destroy the meter. Follow

all safety rules in this manual and the normal safety precautions used in working

with electrical circuits. Do not service this device if you are not qualified to do so.

All repairs should be performed by an authorised Clarke repair facility. To ensure

safe operaton, and in order to achieve the full functionality of the meter, follow the

directions in this manual carefully.

This meter has been designed according to IEC1010 concerning electronic measuring instruments

with an overvoltage category CAT III 600V and pollution 2.

Follow all safety and operating instructions to make sure that the meter is used safely and is

kept in good operating condition.

With proper use and care, the digital meter will give you years of excellent service.

Measurement category III is for measurements performed in building installation. (Examples are

measurements on distribution boards, circuit breakers, wiring including cables, busbars, junction

boxes, switches, socket outlets (fixed installation), equipment for industrial use and some other

equipment; for example, stationary motors with permanent connection to the fixed installation).

SAFETY RULES

1. When using the meter observe all normal safety rules concerning:

• protection against the dangers of electrical current.

• protection of the meter against mis-use.

2. Before using the meter, inspect it carefully to make sure that it has not been damaged during

shipping.

3. The test lead or test clip must be in good condition. Before using, verify that the insulation on

test lead or test clip is not damaged and/or the lead wires are not exposed.

4. Full compliance with safety standards can be guaranteed only if used with test leads supplied.

Use ONLY authorised Clarke replacement parts.

5. Always make sure the correct function and range are selected for your job.

6. Never exceed the limit values (listed in SPECIFICATIONS Section of this manual) for each

range of measurement.

7. When the meter is linked to a circuit, do not touch the probe tip of the meter or the test lead/

test clip.

8. In Manual Mode, when the value scale to be measured is unknown beforehand, select the

highest range.

9. Do not use this tool to measure voltage higher than 600V above earth ground.

10. Always be careful when working with voltages above 60V DC or 30V AC rms. Always keep

fingers behind the probe barrier while measuring.

11. Never connect the meter leads across a voltage source while the Mode Selector is in the

resistance, diode, or continuity mode. Doing so can damage the meter.

12. Never perform resistance, diode, or continuity measurements on live circuits.

13. Before rotating the Mode Selector to change the function, disconnect the probe tip of meter

and the probe of the test lead (or test clip) from the circuit being tested.

14. Never use the meter near explosive air, steam, or dirt.

15. If any faults are observed, STOP using and have the meter serviced by a qualified technician

immediately.

16. Never use the meter unless the outer casing is in place and fully fastened.

17. Do not store or use meter in areas exposed to direct sunlight, high temperature, humidity, or

condensation.

SYMBOLS Important safety information

Double insulation (Protection class II)

CAT III Overvoltage (Installation) category III, Pollution Degree 2 per IEC10101 refers to

the level of Impulse Withstand Voltage protection provided.

Conforms to European union directive

Earth ground

AC Alternating current

DC Direct current

Inhaltsverzeichnis

Andere Clarke Multimeter Handbücher

Clarke

Clarke CDM10A Bedienungsanleitung

Clarke

Clarke CDM 85 Betriebsanleitung

Clarke

Clarke CDM-50 Bedienungsanleitung

Clarke

Clarke CDM-45 Bedienungsanleitung

Clarke

Clarke CDM20 Bedienungsanleitung

Clarke

Clarke CDM 25 Bedienungsanleitung

Clarke

Clarke CDM-35 Bedienungsanleitung

Clarke

Clarke CDM10 Bedienungsanleitung

Clarke

Clarke CDM 10 Bedienungsanleitung

Clarke

Clarke CDM80C Bedienungsanleitung

Clarke

Clarke CDM3 Bedienungsanleitung

Clarke

Clarke CDM10C Bedienungsanleitung

Clarke

Clarke CDM 15 Bedienungsanleitung

Clarke

Clarke CDM 85 Bedienungsanleitung

Clarke

Clarke CDM35C Bedienungsanleitung

Beliebte Multimeter Handbücher anderer Marken

Agilent Technologies

Agilent Technologies 34420A Bedienungsanleitung

Fluke

Fluke 83 Bedienungsanleitung

Hameg

Hameg HM 8012 Bedienungsanleitung

Mastech

Mastech MY70 Bedienungsanleitung

Steren

Steren MUL-300 Bedienungsanleitung

Somogyi Elektronic

Somogyi Elektronic home SMA 92 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRAmax 6 Bedienungsanleitung

PeakTech

PeakTech 4000 Gebrauchs- und Pflegehandbuch

YOKOGAWA

YOKOGAWA 90050B Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRALINE DMM16 Bedienungsanleitung

Fluke

Fluke 8846A Bedienungs- und Wartungshandbuch

Tempo Communications

Tempo Communications MM200 Bedienungsanleitung

Elenco Electronics

Elenco Electronics CM-1555 Bedienungsanleitung

Mastech

Mastech MS8238C Bedienungsanleitung

SDAR

SDAR 830A, 830B, 830D, 830C Bedienungsanleitung

RS PRO

RS PRO RS-9519BT Bedienungsanleitung

BGS technic

BGS technic 8890 Bedienungsanleitung

Amprobe

Amprobe Hexagon 60 Bedienungsanleitung