Clarke Air CAT34B Installations- und Betriebshandbuch

ORBITAL SANDER

Part Nos: 3110434

GC07/13

MODEL No: CAT34B

OPERATING & MAINTENANCE

INSTRUCTIONS

Parts & Service: 020 8988 7400/E-mail:[email protected] or [email protected]

INTRODUCTION

Thank you for purchasing this CLARKE product.

Before attempting to use the sander, please read this manual thoroughly and

follow the instructions carefully. In doing so you will ensure the safety of

yourself and that of others around you, and you can look forward to the

sander giving you long and satisfactory service.

GUARANTEE

This CLARKE product is guaranteed against faulty manufacture for a period of

12 months from the date of purchase. Please keep your receipt as proof of

purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not effect your statutory rights.

ENVIROMENTAL PROTECTION

Do not dispose of this product with general household waste. All tools,

accessories and packaging should be sorted, taken to a recycling

centre and disposed of appropriately.

Parts & Service: 020 8988 7400/E-mail:[email protected] or [email protected]

CONTENTS

Introduction ............................................................................................ 2

Guarantee .............................................................................................. 2

Environmental Protection ...................................................................... 2

Technical Specification ......................................................................... 3

General Safety Precautions .................................................................. 4

Overview ................................................................................................ 7

Assembly ................................................................................................ 7

Operating Instructions ........................................................................... 8

Troubleshooting ...................................................................................... 9

Maintenance ........................................................................................ 10

Parts Lists and Diagrams ..................................................................... 11

Vibration Emissions .............................................................................. 13

Declaration of Conformity .................................................................. 15

Please note that the details and specifications contained herein, are correct at the

time of going to print. However, CLARKE International reserve the right to change

specifications at any time without prior notice.

TECHNICAL SPECIFICATION

erutaeF noitacificepS

thgieWgk2

)hxwxl(snoisnemiD mm021x09x081

deepSeerFdetatSmpr0008

eziSdaP mm561x09

erusserPriAgnik

roW )rab2.6(isp09

noitpmusnoCriAegarevA )nim/l071(mfc6

noitcennoCriAtelnI PSB"4/1

levelerusserpdnuosdethgie

w-A )A(Bd39

levelrewopdnuoS )A(Bd201

eldnahehttanoitarbiVs/m2.4

Parts & Service: 020 8988 7400/E-mail:[email protected] or [email protected]

SAFETY PRECAUTIONS

WORK ENVIRONMENT

• Keep the work area clean and tidy.

• Dress appropriately - Do not wear loose clothing or jewellery. Tie long hair

out of the way.

• Keep children and visitors away - Do not let children handle the sander.

Make sure that any other persons in the work area are dressed suitably

and are wearing eye and ear protectors.

• Keep the air supply hose away from heat, oil and sharp edges.

• Do not fit the sander to any stand or clamping device that may damage

the tool.

GENERAL USE

• Stay alert and use common sense - do not use the sander when you are

tired or under the influence of alcohol, drugs or medication.

• Always wear eye protection when using the sander - eye protection must

provide protection from the front and the side.

• Always wear a dust mask when sanding dusty materials.

• Always wear ear protectors when using the sander.

• Do not over-reach - Keep proper footing and balance at all times.

• Never use any type of bottled gas as a source of power for the sander.

• Do not connect the air supply hose with your finger on the trigger of the

sander.

• Do not exceed the maximum pressure for the sander: 90 psi / 6.2 bar.

• Check hoses for leaks or worn condition before use and ensure that all

connections are secure.

• Do not use the sander for any other purpose than that described in this

booklet.

• Do not carry out any alterations or modifications to the sander.

• The sander should be serviced as required by your CLARKE dealer.

• Never use the sander if it is defective or operating abnormally.

• ALWAYS ensure the workpiece is firmly secured leaving both hands free to

control the sander.

• ALWAYS ensure the sander has stopped before putting it down after use.

Parts & Service: 020 8988 7400/E-mail:[email protected] or [email protected]

• ALWAYS ensure that any attachments are correctly fastened before

connecting the sander to the power supply.

• Always disconnect from the air supply when:

a) performing any maintenance.

b) the sander is not in use.

c) the sander will be left unattended.

d) moving to another work area.

• Avoid damaging the sander for example, by applying excessive force.

• ALWAYS maintain the sander with care. Keep it clean for best and safest

performance.

• Quick change air-line couplings should not be located at the tool. They

add weight and could fail due to vibration.

• DO NOT force or misuse the sander. It will do a better and safer job at the

rate for which it was designed.

• This sander vibrates during use. Vibration may be harmful to your hands or

arms. Stop using the tool if discomfort, a tingling feeling or pain occurs and

seek medical advice before resuming use. Refer to Vibration Emissions on

page 13.

TRANSPORTATION

• Never carry the sander by the air supply hose.

• Never carry the sander with your finger on the trigger.

STORAGE

• When not in use the sander must be disconnected from the air supply and

stored in a dry place out of the reach of children (preferably in a locked

cabinet).

• Avoid storing the sander in environments where the temperature falls

below 0oC.

Parts & Service: 020 8988 7400/E-mail:[email protected] or [email protected]

AIR SUPPLY REQUIREMENTS

WARNING: COMPRESSED AIR CAN BE DANGEROUS. ENSURE THAT YOU

ARE THOROUGHLY FAMILIAR WITH ALL PRECAUTIONS RELATING TO THE

USE OF COMPRESSORS AND COMPRESSED AIR SUPPLY.

• Use only clean, dry, regulated compressed air as a power source.

• Air compressors used with the sander must comply with the appropriate

European Community safety directives.

• A build up of moisture in the air compressor will accelerate wear and

corrosion in the sander. Ensure any moisture is drained from the

compressor daily and the inlet filter is kept clean.

• If an unusually long air hose is required,(over 8 metres), line presure may

need to be increased.

• Never exceed the maximum operating pressure for the tool.

A typical airline arrangement is shown on the below. If an automatic in-

line filter/regulator/lubricator unit is used it will keep the tool in good

condition but should be regularly checked and topped up with oil.

IMPORTANT: If a filter/lubricator unit is not used, the sander should be

lubricated with 2 to 6 drops of oil, at least once a day or after 2 hours work,

depending upon the working environment. The oil can be inserted through

the airline connection point.

Parts & Service: 020 8988 7400/E-mail:[email protected] or [email protected]

AIRLINE SAFETY

• Never exceed the maximum operating pressure for the sander. A pressure

of 90 psi with a flow of 6 cfm is required. Too high an air pressure will

shorten the life of the tool due to excessive wear.

• The air hose must be rated at least 150% of the maximum operating

pressure of the tool.

OVERVIEW

The CAT34B Orbital Sander is ideal for use in the automotive industry or any

task of smoothing wood, fibreglass or body filler. The sander features a

balanced ball-bearing design, rear exhaust & automatic throttle release. The

CAT34B sander holds standard 93 x 232mm sanding sheets which are

available from your CLARKE dealer.

ASSEMBLY

1. Remove the plastic blanking plug

from the connection port of the

sander .

2. Pour 2-3 drops of CLARKE airline

oil into the air inlet. This should be

done regardless of whether or not

a lubricated air supply is to be

used.

3. Connect a suitable hose to the

sander as shown. Use the screw-in

adaptor supplied if required.

4. Connect the other end of the hose to the compressor.

(A whip hose with a quick fit coupling is available from your CLARKE

dealer).

5. Turn on the air supply and check for air leaks. Rectify any found before

proceding.

Your sander is now ready for use.

Fig 1

Parts & Service: 020 8988 7400/E-mail:[email protected] or [email protected]

DISCONNECTING THE AIR SUPPLY

1. Do not disconnect the air supply hose until the compressor has been shut

down and the compressed air released from the air line.

2. Once the pressure has been released, disconnect the airline hose from

the sander.

STORAGE

1. Store the sander safely in its box in a dry, secure environment.

2. If the sander is not to be used for longer than 24 hours, run a few drops of

CLARKE airline oil into the air inlet and run the tool for a few seconds to

ensure that the oil has been well distributed throughout the sander.

3. When storing, ensure the blanking plug is replaced at the airline

connection port once the airline has been disconnected.

OPERATING INSTRUCTIONS

IMPORTANT: Only use sanding sheets designed for use with a rectangular

orbital sander;-pre-cut sheets (93 x 232mm) are available from your

CLARKE dealer.

1 Attach a sanding sheet to the

base of the sander using the

spring-loaded clips at each end

of the base as in Fig 2.

• Ensure the sanding sheet is

correctly aligned with the sander

and pulled tight enough to avoid

any creasing.

2. Place the sander on the

workpiece and press down on the

trigger to start the sander.

3. Adjust the operating speed if

required, by twisting the air

regulator as in Fig 3.

• If very stiff to twist, a screwdriver

can be used.

4. Release pressure from the trigger

to stop the sander.

5. Always ensure the sander has

stopped before putting it down.

Fig 2

Fig 3

SPRING

LOADED

CLIP

Parts & Service: 020 8988 7400/E-mail:[email protected] or [email protected]

TROUBLESHOOTING

MOTPMYS MELBORP NOITULOS

snurlooTlamronta

swolstubdeepsrednu

daol.

.nrowstraprotoM.1

gnikcitsronroW.2

kcaloteudmsinahcem

.tnaci

rbulfo

luahrevorofrelaedotnruteR.1

liognitacirbullootriapirD.2

kaosdnatelniriaotni

.strapgnivom

riA.ylwols

snurlooT

morfylthgilswolf

.tsuahxe

htiwdemmajstraprotoM.1

.selcitraptridro/&mug

desolcnirotalugeR.2

.noitis

dekcolbwolfrialareneG.3

.tridyb

rofretlifriatelnienimaxE.1

.ssenilnaelc

nepootrotalugertsujdA.2

.noitisop

trohsnilootetarepO.3

.stsrub

riA.nurtonlliwlooT

morfyleerfswolf

.tsuahxe

oteudkcutssenavrotoM.1

.laretamng

ieroffopudliub

&ylppusriatcennocsiD.1

ylbmessalootetator

.yllaunam

trohsnilootgnitarepoyrT.2

.stsrub

.3yltne

ggnisuohrotompaT

.tellamrebburhtiw

liognitacirbullootriapirD.4

kaosdnatelniriaotni

.strapgnivom

.ffotuhsto

nlliwlooTdegamadsgnir-OelttorhT.1

.taesnidegdolsidro

otnruterrognir-OecalpeR.1

relaedekralC

In the event that any of the above situations occurs, requiring the dismantling

and overhaul of the tool, contact your CLARKE International Service

Department on 020-8988-7400.

Parts & Service: 020 8988 7400/E-mail:[email protected] or [email protected]

MAINTENANCE

WARNING! Make sure that the sander is disconnected from the air supply

before starting any cleaning or maintenance procedures.

DAILY

• Drain water from the compressor air tank

and air-line.

• Pour a few drops of CLARKE air line oil**,

into the air inlet. This should be carried out

regardless of whether or not an air line

lubricator is used. If an air-line lubricator is

not used, this procedure should be

repeated after every two to three hours of

use.

WEEKLY

• Check the air inlet screen filter in Fig 3 and

clean if necessary.

CLEANING

• Keep the body of the sander clean and free from debris. Grit or gum

deposits in the tool may reduce efficiency.

• After extensive use, remove the screen filter and flush out the sander with

gum solvent oil or an equal mixture of SAE No10 oil and paraffin. Allow to

dry before use.

SERVICING AND REPAIRS

• Major servicing and repair should be carried out by a qualified service

technician.

PERFORMANCE

Please note that factors other than the tool may effect its operation and

efficiency such as reduced compressor output, excessive drain on the airline,

moisture or restrictions in the line, or the use of connectors of improper size or

poor condition which will reduce air supply.

**Clarke Air Line Oil is available from your CLARKE dealer part no. 3050825.

ACCESSORIES

A wide range of airline accessories are available including filter/regulators,

lubricators, high pressure hoses, adaptors and connectors etc. Contact your

CLARKE dealer for further information, or call CLARKE International on 01992

565333.

Air Inlet Screen

Filter (located

here)

Fig 4

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Clarke Sander Handbücher

Clarke

Clarke air CAT25B Installations- und Betriebshandbuch

Clarke

Clarke 07100A Bedienungsanleitung

Clarke

Clarke air CAT49 Installations- und Betriebshandbuch

Clarke

Clarke American 12 Montage- und Wartungsanleitung

Clarke

Clarke CAT38 Bedienungsanleitung

Clarke

Clarke ALTO C2K Series Bedienungsanleitung

Clarke

Clarke American Sanders RS-16 HDTR Bedienungsanleitung

Clarke

Clarke OBS-18 Bedienungsanleitung

Clarke

Clarke DWS225LR Bedienungsanleitung

Clarke

Clarke Super 7R Bedienungsanleitung

Clarke

Clarke EZ Sand Installations- und Benutzerhandbuch

Clarke

Clarke 07097A Bedienungsanleitung

Clarke

Clarke X-Pro CAT136 Installations- und Betriebshandbuch

Clarke

Clarke PS105 Bedienungsanleitung

Clarke

Clarke COS200 Installations- und Betriebshandbuch

Clarke

Clarke 504 Bedienungsanleitung

Clarke

Clarke 07032C Bedienungsanleitung

Clarke

Clarke 01207A Bedienungsanleitung

Clarke

Clarke JETSTAR 1600 Bedienungsanleitung

Clarke

Clarke Contractor CON180 Installations- und Betriebshandbuch

Clarke

Clarke 07012A Bedienungsanleitung

Clarke

Clarke CROS1 Installations- und Betriebshandbuch

Clarke

Clarke FM-2000 Bedienungsanleitung

Clarke

Clarke CROS3 Bedienungsanleitung

Beliebte Sander Handbücher anderer Marken

Oliver

Oliver 6305 Bedienungsanleitung

Jet

Jet 22-44 Pro-3 Service-Handbuch

Makita

Makita M9204 Handbuch

Makita

Makita M9204 Bedienungsanleitung

Chicago Pneumatic

Chicago Pneumatic CP9778 Bedienungsanleitung

Nitto Kohki

Nitto Kohki BB-20 Bedienungsanleitung

Ferm

Ferm FEOS-135 Bedienungsanleitung

Unior

Unior 1510 Bedienungsanleitung

stayer

stayer ls1200 Bedienungsanleitung

Jet

Jet JSG-96 Service-Handbuch

Parkside

Parkside PDS 290 B2 Bedienungsanleitung

Status

Status XPA Series Bedienungsanleitung

Craftsman

Craftsman 113.22521 Bedienungsanleitung

Craftsman

Craftsman 113.225831 Bedienungsanleitung

CLAS

CLAS OP 1429 Bedienungsanleitung

Parkside

Parkside PEXS 270 Al Bedienungsanleitung

Makita

Makita 9207SPB Bedienungsanleitung

Flex

Flex ST 1005 VE Bedienungsanleitung

Clarke air CAT34B Installations- und Betriebshandbuch

Beliebte Sander Handbücher anderer Marken